2017 MAZDA MODEL CX-5 light

The front passenger's side and rear windows can be opened/closed when the power window
lock switch on the driver's door is in the unlock position. Kee p this switch in the locked
position while children are in the vehicle.

Close
Close
Open
Open
Right rear
window
Driver's
window
Power window
lock switch
Driver's side Front passenger's side/
Rear windows
Front
passenger's
window
Left rear
windowLocked
position
Unlocked
position
Locked
position
Unlocked
position
Without outside mirror
folding switch
With outside mirror
folding switch
NOTE
•A power window may no longer open/close if you continue to press the switch after fully
opening/closing the power window. If the power window does not open/close, wait a
moment and then operate the switch again.
•The passenger windows may be opened or closed using the master control switches on the
driver's door.
•The power window can be operated for about 40 seconds after the ignition is switched
from ON to ACC or off with all doors closed. If any door is opened, the power window
will stop operating.
For engine-off operation of the power windo w, the switch must be held up firmly
throughout window closure because the auto -closing function will be inoperable.
•When the power window lock switch is in the locked position, the light on each power
window switch, except for the driver's power window switch, turns off. The light may be
difficult to see depending on the surrounding brightness.
▼Opening/Closing Windows (Type B)
The Type B power window is equipped with an automatic open/clos
e function on the
driver's power window, and AUTO is marked on the driver's power window switch.
The window opens while the switch is pressed and it closes whil e the switch is pulled up
with the ignition switched ON. Do not open or close three or mo re windows at the same
time.
Before Driving
Windows
3-41
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Modification and Add-OnEquipment
Mazda cannot guarantee the immobilizer
and the theft-deterrent systems' operation
if the system has been modified or if any
add-on equipment has been installed.
CAUTION
To avoid damage to the vehicle, do not
modify the system or install any add-on
equipment to the immobilizer and the
theft-deterrent systems or the vehicle.
Immobilizer System
The immobilizer syste m allows the engine
to start only with a key the system
recognises.

If someone attempts to start the engine
with an unrecognised key, the engine will
not start, thereby helping to prevent
vehicle theft.
If you have a problem with the
immobilizer system or the key, consult an
Authorised Mazda Repairer.
CAUTION
 Changes or
modifications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
 To avoid damage to the key, do not:
 Drop the key.
 Get the key wet.
 Expose the key to any kind of magnetic
field.
 Expose the key to high temperatures
on places such as the instrument panel
or bonnet, under direct sunlight.
 If the engine does not start with the
correct key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorised Mazda Repairer.
NOTE
•The keys carry a unique electronic code.
For this reason, and to assure your
safety, obtaining a replacement key
requires some waiting time. They are
only available through an Authorised
Mazda Repairer.
Before Driving
Security System
3-47
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•Always keep a spare key in case one is
lost. If a key is lost, consult an
Authorised Mazda Repairer as soon as
possible.
•If you lose a key, an Authorised Mazda
Repairer will reset the electronic codes
of your remaining keys and immobilizer
system. Bring all the remaining keys to
an Authorised Mazda Repairer to reset.
Starting the vehicle with a key that has
not been reset is not possible.
▼Operation
NOTE
•The engine may not start and security
indicator light may illuminate or flash if
the key is placed in an area where it is
difficult for the system to detect the
signal, such as on the instrument panel
or in the glove comp
artment. Move the
key to a location within the signal
range, switch the ignition off, and then
restart the engine.
•Signals from a TV or radio station, or
from a transceiver or mobile telephone
could interfere with your immobilizer
system. If you are using the proper key
and the engine fails to start, check the
security indicator light.
Arming
The system is armed when the ignition is
switched from ON to off.
The security indica tor light in the
instrument cluster flashes every 2 seconds
until the system is disarmed.

Disarming
The system is disarmed when the ignition
is switched ON with the correct
programmed key. The security indicator
light illuminates for about 3 seconds and
then turns off. If the engine does not start
with the correct key, and the security
indicator light remains illuminated or
flashing, try the following:
Make sure the key is within the
operational range for signal transmission.
Switch the ignition off, and then restart the
engine. If the engine d oes not start after 3
or more tries, contact an Authorised
Mazda Repairer.
NOTE
•If the security indicator light flashes
continuously while you are driving, do
not shut off the engine. Go to an
Authorised Mazda Repairer and have it
checked. If the engine is shut off while
the indicator light is flashing, you will
not be able to restart it.
•Because the electronic codes are reset
when the immobilizer system is repaired,
the keys are needed. Make sure to bring
all the keys to an Authorised Mazda
Repairer so that they can be
programmed.
Before Driving
Security System
3-48
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Theft-Deterrent System*
If the theft-deterrent system detects an
inappropriate entry in to the vehicle or the
intrusion sensor detects movement in the
vehicle which could result in the vehicle
(with the intrusion sensor) or its contents
being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the siren/horn and flashing the
hazard warning lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion s ensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.

The intrusion s ensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to operate
appropriately, be aware of the following:
 Do not hang clothing or objects from a
head restraint or a coat hook.
 Return the extension sunvisors to their
original positions.
 Do not blind the intrusion sensor by
covering it or placing objects over it.
 Do not allow the intrusion sensor to get
soiled or wipe it with a liquid.
Do not shock or cause an impact to the
intrusion sensor or the intrusion sensor
bezel.
 Do not install seats that are not Mazda
genuine products.
 To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are higher
than the head restraints.

Intrusion sensor and
intrusion sensor bezel
▼ Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights flash for about
30 seconds when the system is triggered
by any one of the following:
•Unlocking a door with the auxiliary key
or an inside door-lock knob.
•Forcing open a door, the bonnet or the
liftgate.
•Opening the bonnet by operating the
bonnet release handle.
•Switching the ignition ON without using
the push button start.
•(With the intr
usion sensor)
The intrusion sensor detects a movement
in the vehicle.
Before Driving
Security System
*Some models.3-49
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

The system will be triggered again (up to
10 times) if one of the above conditions
remains.
•(With the intrusion sensor)
Disconnecting the battery terminal (the
hazard warning lights do not flash).
The system will be triggered about 10
times.
NOTE
•The liftgate does not open while the
theft-deterrent system is operating.
•For vehicles equipped with the power
liftgate, the liftgate can be opened even
while the theft-deterrent system is
operating by pressing the power liftgate
button on the transmitter or the electric
liftgate opener switc h while carrying the
key.
•If the battery goes dead while the
theft-deterrent system is armed, the
siren/horn will activate and the hazard
warning lights will flash when the
battery is charged or replaced.
▼ How to Arm the System
1. Close the windows and the sunroof*
securely.
NOTE
(With the intrusion sensor)
Even with a window or the sunroof
*
open, the system can be armed,
however, leaving the windows and the
sunroof
* even partially open can invite
theft, and wind blowing into the
vehicle could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion
Sensor (With Intrusion Sensor) on
page 3-51.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and the liftgate are closed.
4. Press the lock butto n on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will flash
once.
(With the advanced keyless function)
Press a request switch.

The security indicator light in the
instrument cluster flashes twice per
second for 20 seconds.

5. After 20 seconds, the system is fully armed.
NOTE
•The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate and the bonnet closed.
Refer to Transmitter on page 3-4.
•The system will disarm if one of the
following operations takes place
within 20 seconds after pressing the
lock button:
•Unlocking any door.
•Opening any door.
•Opening the bonnet.
•Switching the ignition ON.
To rearm the system, do the arming
procedure again.
Before Driving
Security System
3-50*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary
key while the theft-deterrent system
is armed, the hazard warning lights
will flash once to indicate that the
system is armed.
▼Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the
alarm from triggering
unnecessarily.
•Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
•Leaving an object inside the vehicle that
can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
•Hanging small objects/accessories in the
vehicle, hanging clothing on a coat
hook, or placing other items which can
move easily inside the vehicle.
•Parking in an area where there is strong
vibration or loud noise.
•When using a high pressure or
automatic car wash.
•Continuous shock and vibration from
hail or thunder and lightning is
transmitted to the vehicle.
•Doors are locked with a window or the
sunroof
* left open.
•An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the liftgate remains closed
for 30 seconds, all the doors and the
liftgate automatically re-lock and the theft
deterrent system arms even if a window
and the sunroof
* is left open.

To cancel the intrusion sensor, press the
intrusion sensor cancel button on the
transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will flash three
times.
NOTE
•To reactivate the intrusion sensor, turn
off the armed theft-deterrent system and
then rearm it.
•The intrusion sensor is operational
when the theft-deterrent system is
armed. To cancel the intrusion sensor,
press the intrusion sensor cancel button
each time the theft-deterrent system is
armed.
▼ To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
•Pressing the unlock button on the
transmitter.
•Starting the engine with the push button
start.
•(With the advanced keyless function)
•Pressing a request switch on the
doors.
The hazard warning lights will flash twice.
Before Driving
Security System
*Some models.3-51
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
When the doors are unlocked by pressing
the unlock button on the transmitter while
the theft-deterrent system is turned off, the
hazard warning lights will flash twice to
indicate that the sy stem is turned off.
▼To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
•Pressing the unlock button on the
transmitter.
•Starting the engine with the push button
start.
•(With the advanced keyless function)
•Pressing a request switch on the
doors.
•Pressing the electric liftgate opener
while the key is being carried.
•Pressing the power liftgate button on
the transmitter.
The hazard warning lights will flash twice.
Before Driving
Security System
3-52
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Rocking the Vehicle
WA R N I N G
Do not spin the wheels at high speed, and
do not allow anyone to stand behind a
wheel when pushing the vehicle:
When the vehicle is stuck, spinning the
wheels at high speed is dangerous. The
spinning tyre could overheat and explode.
This could cause serious injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever/
selector lever from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, flares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
•Have the proper ratio of antifreeze in the
radiator.
Refer to Engine Coolant on page 6-29.
•Inspect the ba ttery and its leads. Cold
reduces battery capacity.
•Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-25).
•Inspect the ignition system for damage
and loose connections.
•Use washer fluid made with
antifreeze―but do not use engine
coolant antifreeze for washer fluid (page
6-32).
NOTE
•Remove snow before driving. Snow left
on the windscreen is dangerous as it
could obstruct vision.
•Do not apply excessive force to a
window scraper when removing ice or
frozen snow on the mirror glass and
windscreen.
•Never use warm or hot water for
removing snow or ice from windows and
mirrors as it could result in the glass
cracking.
Before Driving
Driving Tips
3-56
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2