2017 MAZDA MODEL CX-5 fog light

Air intake selector
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (
)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traffic (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (
)
Outside air is allowed to enter the cabin.
Use this mode for ventilation or
windscreen defrosting.
WA R N I N G
Do not use the position in cold or rainy
weather:
Using the
position in cold or rainy
weather is dangerous as it will cause the
windows to fog up. Your vision will be
hampered, which could lead to a serious
accident.
DUAL switch
Use the DUAL switch to change the mode
between the individual operation (driver
and passenger) and interconnection
(simultaneous) modes.
Individual operation mode (indicator
light illuminated)
The set temperature can be controlled
individually for the driver and front
passenger.
Interconnection mo de (indicator light
turned off)
The set temperature for the driver and
front passenger is controlled
simultaneously.
Windscreen defroster switch
Press the switch to defrost the windscreen
and front door windows.
Refer to Windscreen Defrosting and
Defogging on page 5-14.
Rear window defogger switch
Press the rear window defogger switch to
defrost the rear window.
Refer to Rear Window Defogger on page
4-76.
▼ Operation of Automatic
Air-conditioning
1. Press the AUTO switch. Selection of
the airflow mode, air intake selector
and amount of airflow will be
automatically controlled.
2. Use the temperature control dial to select a desired temperature.
Press the DUAL switch or turn the
front passenger temperature control
dial to control the set temperature
individually for the driver and front
passenger.
To turn off the system, press the OFF
switch.
NOTE
•Setting the temperature to maximum hot
or cold will not provide the desired
temperature at a faster rate.
Interior Features
Air-Conditioning System
5-13
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•When selecting heat, the system will
restrict airflow until it has warmed to
prevent cold air from blowing out of the
vents.
▼Windscreen Defrosting and
Defogging
Press the windscreen defroster switch.
In this position, the outside air position is
automatically selected, and the air
conditioner automatically turns on. The air
conditioner will direct
ly dehumidify the
air to the front windscreen and side
windows on page 5-6.
Airflow amount wil l be increased.
WA R N I N G
Set the temperature control to the hot or
warm position when defogging (
position):
Using the
position with the temperature
control set to the cold position is
dangerous as it will cause the outside of the
windscreen to fog up. Your vision will be
hampered, which could lead to a serious
accident.
NOTE
Use the temperature control dial to
increase the air flow temperature and
defog the windscreen more quickly.
▼ Sunlight/Interior temperature
sensor
Sunlight sensor
Do not place objects on the sunlight
sensor. Otherwise, the interior temperature
may not adjust correctly.
Sunlight sensor
Interior temperature sensor
Do not cover the interior temperature
sensor. Otherwise, the interior temperature
may not adjust correctly.
Interior temperature sensor
Interior Features
Air-Conditioning System
5-14
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the CD and must not be used. Anything
that can damage, warp, or fog plastic
should never be used to clean CDs.
•The CD player ejects the CD if the CD
is inserted upside down. Also dirty
and/or defective CDs may be ejected.
•Do not insert cleani ng discs in the CD
player.
•Do not insert any disc with a peel-off
seal affixed to it.
•This unit may not be able to play certain
CD-R/CD-RWs made using a computer
or music CD recorder due to disc
characteristics, scratches, smudges, dirt,
etc., or due to dust o r condensation on
the lens inside the unit.
•Storing CDs in the vehicle exposed to
direct sunlight or high temperature may
damage the CD-R/CD-RWs, and make
them unplayable.
•CD-R/CD-RW exceeding 700 MB
cannot be played.
•This unit may not be able to play certain
discs made using a computer due to the
application (writing software) setting
used. (For details, consult the store
where the application was purchased.)
•It is possible that certain text data, such
as titles, recorded on a CD-R/CD-RW
may not be displayed when musical data
(CD-DA) is playing.
•The period from when a CD-RW is
inserted to when it begins playing is
longer than a normal CD or CD-R.
•Completely read the instruction manual
and cautions for CD-R/CD-RWs.
•Do not use discs with cellophane tape
adhering, partially peeled off labels, or
adhesive material exuding from the
edges of the CD label. Also, do not use
discs with a commercially-available
CD-R label affixed. The disc may not
eject resulting in a malfunction.
▼ Operating Tips for MP3
MP3 stands for MPEG Audio Layer 3,
which is standardised voice compression
established by the ISO
*1 working group
(MPEG).
Use of MP3 allows for audio data to be
compressed to approximately a tenth of
the source data size.
This unit plays files with the extension
(.mp3) as MP3 files.
*1 International Organisation for Standardisation
CAUTION
Do not use an audio file extension on files
other than audio files. In addition, do not
change the audio file extension. Otherwise,
the unit will not recognise the file correctly
resulting in noise or a malfunction.
Interior Features
Appendix
5-134
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•Be sure never to touch the signal surface
when handling the DVDs. Pick up a
DVD by grasping the outer edge or the
edge of the hole and the outer edge.
•Do not stick paper or tape on the DVD.
Avoid scratching the reverse side (the
side without a label). The disc may not
eject resulting in a malfunction.
•Dust, finger smudges, and dirt can
decrease the amount of light reflected
from the signal surface, thus affecting
sound quality. If the DVD should
become soiled, gently wipe it with a soft
cloth from the centre of the DVD to the
edge.
•Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the DVD and must not be used.
Anything that can damage, warp, or fog
plastic should never be used to clean
DVDs.
•The DVD player ejects the DVD if the
DVD is inserted upside down. Also dirty
and/or defective DVDs may be ejected.
•Do not insert cleani ng discs in the DVD
player.
•Do not insert any disc with a peel-off
seal affixed to it.
•This unit may not be able to play certain
DVD-R/DVD
R/DVD-RW/DVD
RWs made using a computer or DVD
recorder due to disc characteristics,
scratches, smudges, dirt, etc., or due to
dust or condensation on the lens inside
the unit.
•Storing DVDs in the vehicle exposed to
direct sunlight or high temperature may
damage the DVD-R/DVD
R/
DVD-RW/DVD
RWs, and make them
unplayable.
•This unit may not be able to play certain
discs made using a computer due to the
application (writing software) setting
used. (For details, consult the store
where the application was purchased.)
•Completely read the instruction manual
and cautions for DVD-R/DVD
R/
DVD-RW/DVD
RW s .
•Do not use discs with cellophane tape
adhering, partially peeled off labels, or
adhesive material exuding from the
edges of the DVD label. Also, do not
use discs with a commercially-available
DVD-R label affixed. The disc may not
eject resulting in a malfunction.
•The conditions in w hich a DVD video
can be played may be pre-determined
depending on the inte ntions of the disc
software creator. Functions may not
operate as the user intends because this
DVD player operates according to the
design intentions of the software creator.
Always refer to the instructions
accompanying the disc to be played.
•Manufactured under license by Dolby
Labouratories, Inc.. Dolby and the
double-D symbol are trademarks of
Dolby Labouratories.
Interior Features
Appendix
5-138
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Light Bulbs
Type A
Type B
Headlights (High/Low beam)
Running lights/Position lights
Headlights (Low beam)*
Running lights*
Front fog lights*
Front direction indicator lights
Position lights
Side direction indicator lights
Brake lights
Maintenance and Care
Owner Maintenance
*Some models.6-47
2017-6-7 7:51:19Form No. CX-5 8FY4-EE-17E+L_Edition2

Brake lights/Tail lights
Rear direction indicator lights
Reverse lights
Rear fog light (Left-hand drive model)*
Rear fog light (Right-hand drive model)*
High-mount brake light
Number plate lights
Overhead lights/Front map lights
Vanity mirror lights*
Rear map lights
Luggage compartment light
WA R N I N G
Never touch the glass portion of a halogen
bulb with your bare hands and always
wear eye protection when handling or
working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurised gas. If one is broken, it will
explode and serious injuries could be
caused by the
flying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the reach
of children:
Playing with a halogen bulb is dangerous.
Serious injuries could be caused by
dropping a halogen bulb or breaking it
some other way.
CAUTION
When removing the lens or lamp unit using
a flathead screwdriver, make sure that the
flathead screwdriver does not contact the
interior terminal. If the flathead screwdriver
contacts the terminal, a short circuit may
occur.
NOTE
•To replace the bulb, contact an expert
repairer, we recommend an Authorised
Mazda Repairer.
•If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
•Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
Maintenance and Care
Owner Maintenance
6-48*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Replacing Exterior Light Bulbs
Headlights, Running lights/Position
lights (Type A), Ru
nning lights (Type
A), Front fog lights*, Side direction
indicator lights, Bra ke lights (Type A),
Brake lights/Tail lights (Type A),
Reverse lights, High-mount brake light
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorised Mazda
Repairer when the replacement is
necessary.
Front direction indicator lights, Position
lights (Type B)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the bonnet. Refer to Bonnet on page 6-22.
3. Turn the socket and bulb assembly anticlockwise and remove it.
4. Disconnect the bulb from the socket. Front direction indicator lights
Position lights
5. Install the new bulb in the reverse
order of the removal procedure.
Running lights (Type B)
*
1. Make sure the ignition is switched off, and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
3. Pull the centre of each plastic retainer
using a flathead screwdriver and
remove the retainers, and then partially
peel back the over fender.
Removal
Installation
Maintenance and Care
Owner Maintenance
*Some models.6-49
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

6. Disconnect the bulb from the socket.Rear direction indicator lights
Brake lights/Tail lights
7. Install the new bulb in the reverseorder of the removal procedure.
Rear fog light
*
1. Make sure the ignition is switched off and the headlight switch is off.
2. Pull the centre of each plastic retainer and remove the retainers.
3. Remove the cover.
Removal
Installation
4. Turn the socket and bulb assembly
anticlockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order of the removal procedure.
Number plate lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the
lens, and then remove the lens by
carefully prying on t he edge of the lens
with a flathead screwdriver.
Maintenance and Care
Owner Maintenance
*Some models.6-51
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2