2017 MAZDA MODEL CX-5 instrument panel

The rear fog light indicator light in the
instrument cluster illuminates while the
rear fog light is on.

Fog light switch
To turn the rear fog light off, do any of the
following:
•Rotate the fog light switch to the
position again (the fog light switch
returns to its original position
automatically).
•Turn the headlight switch to the
position.
The rear fog light indicator light in the
instrument cluster goes off when the rear
fog light is turned off.
NOTE
(With auto-light control)
When the headlight switch is in the
position and the headlights, exterior lights
and instrument panel illuminated, the rear
fog light turns on when the rear fog light
switch is turned on.
Turn and Lane-Change Signals
The ignition must be switched ON to use
the turn and lane-change signals.
▼Direction Indicators
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.

If the indicator light continues to flash
after a turn, ma
nually return th e lever to its
original position.
Right turn
Left turn
Right lane change
Left lane change OFF
The direction indicato
rs in the instrument
cluster flash according to the operation of
the direction indicator lever to show which
signal is working.

NOTE
•If an indicator light stays on without
flashing or if it flashes abnormally, one
of the direction indicator bulbs may be
burned out.
•A personalised function is available to
change the turn indicator sound volume.
(page 9-12)
When Driving
Switches and Controls
4-70
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

If the BSM warning indicator lights are difficult to see due to glare from surrounding
brightness when travelling on snow-covered roads or under foggy conditions, press the
dimmer cancellation button to cancel the dimmer and increase th e brightness of BSM
warning indicator light s when they turn on.
Refer to Instrument Panel Illumination on page 4-26.
Display indicato r (Vehicles with multi-i nformation display and active driving display)
The detected approaching vehicle and warning are displayed in t he multi-information
display and active driving display when the vehicle is moving f orward (BSM operational).
Multi-information DisplayActive Driving Display
Detection and warning indicator Detection and warning indicator
The detected direction is displayed with a detection indicator (white) when an approaching
vehicle is detected. In addition, if the direction indicator le ver is operated to signal a lane
change while the vehicle is detected, the display changes the c olour (amber) of the warning
indicator.
BSM warning beep
The BSM warning beep is activated simultaneously with the flash ing of a BSM warning
indicator light.
▼ Cancelling Operation of Blind Spot
Monitoring (BSM)
The BSM system can be set to inoperable.
Refer to Personalisation Features on page
9-12.
When the BSM is set to inoperable, the
BSM and Rear Cross Traffic Alert
(RCTA) systems are turned off and the
BSM OFF indicator light in the instrument
cluster turns on.
NOTE
When the ignition is
switched OFF, the
system status before it was turned off is
maintained. For exampl e, if the ignition is
switched OFF while the BSM and Rear
Cross Traffic Alert (RCTA) systems are
operational, the BSM and Rear Cross
Traffic Alert (RCTA) systems remain
operational the next time the ignition is
switched ON.
When Driving
i-ACTIVSENSE
4-119
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

WA R N I N G
Always check the traffic signs visually while driving.
The TSR helps prevent the driver from overlookin g traffic signs and provides support for safer
driving. Depending on the weath er conditions or problems with
traffic signs, a
traffic sign
may not be recognised or a traffic sign different from the actual traffic sign may be displayed.
Always make it your responsibility as a driver to check the actual
traffic signs. Otherwise, it
could result in an accident.
NOTE
•The TSR does not operate if there is a malf unction in the Forward Sensing Camera (FSC).
•Under the following conditions, the TSR may not operate normally.
•An object placed on the instrument panel is reflected in the windscreen and picked up
by the camera.
•Heavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is tilted.
•The tyre pressures are not adjusted to the specified pressure.
•Tyres other than standard tyres are equipped.
•The vehicle is driven on the ramp and surrounding area to or from a rest area or a
tollgate on a highway.
•When surrounding brightness suddenly changes such as when entering or exiting a
tunnel.
•The illumination of the headlights is weakened because of dirt or the optical axis is
deviated.
•The windscreen is dirty or foggy.
•The windscreen and camera are fogged (water droplets).
•Strong light is directed at the front of the vehicle (such as backlight or high-beam
headlights of on-coming vehicles).
•The vehicle is making a sharp turn.
•Strong light reflects off the road.
•A traffic sign is in a position which makes it difficult to reflect the light from the
vehicle's headlights, such as when the vehicle is driven at night or in a tunnel.
•The vehicle is driven under weather conditions such as rain, fog, or snow.
•The stored map data for the navigation system is not current.
•A traffic sign is obscured by mud or snow.
•A traffic sign is concealed by trees or a vehicle.
•A traffic sign is partially shaded.
•A traffic sign is bent or warped.
•A traffic sign is too low or too high.
•A traffic sign is too bright or too dark (including electronic traffic signs).
When Driving
i-ACTIVSENSE
4-121
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•If the steering wheel, accelerator pedal, or brake pedal is operated abruptly and the
vehicle moves close to a white (yellow) line, the system determines that the driver is
making a lane change and the LAS&LDWS operation is temporarily cancelled. The
LAS&LDWS becomes operational again when the system detects white (yellow) lane lines
while the vehicle is being driven normally within its vehicle lane.
•If the vehicle deviates from its lane repeatedly within a short period of time, the
LAS&LDWS may not operate.
•When white (yellow) lane lines are not detected, the LAS&LDWS does not operate.
•Under the following conditions, the LAS&LDWS may not be able to detect white (yellow)
lane lines correctly and it may not operate normally.
•If an object placed on the instrument panel is reflected in the windscreen and picked up
by the camera.
•Heavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is tilted.
•The tyre pressures are not adjusted to the specified pressure.
•Tyres other than conventional tyres are equipped.
•Vehicle is driven on an intersection or junction, or on a forked road.
•The white (yellow) lane lines are less visi ble because of dirt or fading/patchiness.
•A vehicle in front of your vehicle is running near a white (yellow) lane line making it
less visible.
•A white (yellow) lane line is less visible because of bad weather (rain, fog, or snow).
•The vehicle is driven on a temporary lane or section with a closed lane resulting from
construction where there may be multiple wh ite (yellow) lane lines or they are
interrupted.
•A misleading line is picked up on the road su ch as a temporary line for construction, or
because of shade, lingering snow, or grooves filled with water.
•The surrounding brightness suddenly changes such as when entering or exiting a
tunnel.
•The illumination of the headlights is weakened because of dirt or the optical axis is
deviated.
•The windscreen is dirty or foggy.
•The windscreen, camera is fogged (water droplets).
•Back-light is reflected off the road surface.
•The road surface is wet and shiny after rain, or there are puddles on the road.
•The shade of a guardrail parallel to a white (yellow) lane line is cast on the road.
•The width of the driving lane is narrow or wide.
•Driving on roads with tight curves.
•The road is excessively uneven.
•The vehicle is shaken after hitting a road bump.
•There are two or more adjacent white (yellow) lane lines.
When Driving
i-ACTIVSENSE
4-165
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

As an added safety feature, your vehicle has been equipped with a tyre pressure monitoring
system (TPMS) that illuminates a low tyre pressu re telltale when one or more of your tyres is
significantly under-inflated. Accordingly, wh en the low tyre pressure telltale illuminates,
you should stop and check your tyres as soon as possible, and inflate them to the proper
pressure. Driving on a significantly under-infla ted tyre causes the tyre to overheat and can
lead to tyre failure. Under-inflation also reduc es fuel efficiency and tyre tread life, and may
affect the vehicle's handling and stopping ability.
Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the
driver's responsibility to maintain correct ty re pressure, even if under-inflation has not
reached the level to trigger illumination of the TPMS low tyre pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when
the system is not operating properly.
The TPMS malfunction indicator is combined with the low tyre pressure telltale. When the
system detects a malfunction, the telltale wi ll flash for approximately one minute and then
remain continuously illuminated. This sequence will continue upon subsequent vehicle
start-ups as long as the malfunction exists. When the malfunction indicator is illuminated,
the system may not be able to detect or signal low tyre pressure as intended. TPMS
malfunctions may occur for a variety of reasons, including the installation of replacement
or alternate tyres or wheels on the vehicle th at prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale af ter replacing one or more tyres or wheels on
your vehicle to ensure that the replacement or alternate tyres and wheels allow the TPMS to
continue to function properly.
 To avoid false readings, the system samples for a little while before indicating a problem. As
a result it will not instantaneously regi ster a rapid tyre deflation or blow out.
▼System Error Activation
When the warning light flashes, there may
be a system malfunction. Consult an
Authorised Mazda Dealer.
A system error activation may occur in the
following cases:
•When there is equipment or a device
near the vehicle using the same radio
frequency as that of the tyre pressure
sensors.
•When a metallic device such as a
non-genuine navigation system is
equipped near the centre of the
instrument panel, which may block
radio signals from the tyre pressure
sensor to the receiver unit.
•When using the following devices in the
vehicle that may cause radio
interference with the receiver unit.
•A digital device such as a personal
computer.
•A current converter device such as a
DC-AC converter.
•When excess snow or ice adheres to the
vehicle, especially around the wheels.
•When the tyre pressure sensor batteries
are exhausted.
•When using a wheel with no tyre
pressure sensor installed.
•When using tyres with steel wire
reinforcement in the side walls.
•When using tyre chains.
When Driving
Tyre Pressure Monitoring System
4-213
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Selecting the Airflow Mode
Instrument panel Vents
Instrument panel and Floor Vents
Floor Vents Defroster and Floor Vents
Defroster Vents
* With rear vents
NOTE
The location airflow exits the air vents an d the airflow amount may change depending on
the open or close status of the air vents.
Interior Features
Air-Conditioning System
5-6
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Maintenance Monitor
▼Maintenance Monitor (Type A audio)
“Oil Change” with flexible setting*1 is available. Consult an Au
thorised Mazda Repairer for
details
*2. When the engine oil flexible maintenance setting is selected, the wrench indicator
light in the instrument cluster w ill be illuminated when remaining oil life becomes less than
1,000 km (600 mile), or remaining days are less than 15 (Whiche ver comes first).
Reset method
Press and hold the instrument panel illumination knob with the ignition switched off, then
switch it on. Keep pressing the instrument panel illumination k nob for more than 5 seconds.
The master warning light will flash for a few seconds when the reset is completed.
Instrument panel illumination knob
*1 The engine oil flexible maintenance setting is available (only some models). Based on
the engine operating conditions, the onboard computer in your v ehicle calculates the
remaining oil life.
*2 When the engine oil flexible maintenance setting is selected, the system must be reset
whenever replacing the engine oil regardless of the wrench indi cator light display.
Maintenance and Care
Scheduled Maintenance
6-17
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the instrument panel illumination knob pressed, and press and hold the instrument panel illumination knob for about 5 seconds until the master
warning light
flashes.

Instrument panel illumination knob
3. After the master warning light flashes for several seconds, the initialization is
completed.
▼ Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal operating temperature.
3. Turn it off and wait at least 5 minutes for the oil to return to the sump.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
SKYACTIV-G 2.0 and
SKYACTIV-G 2.5

MAX
OK
MIN
Maintenance and Care
Owner Maintenance
6-28
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2