TabItem Explanation
Oil Change Oil life (%) Displays the engine oil life un
til the oil replacement is due.
The wrench indication/indicator l ight in the instrument cluster
will be illuminated when remai ning oil life distance is less
than 1,000 km (600 mile), or remaining days are less than 15
(whichever comes first).
Reset Resets the remaining oil life to 100 %.
The system must be reset whenever replacing the engine oil.
Maintenance and Care
Scheduled Maintenance
6-19
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2
(SKYACTIV-D 2.2)
SKYACTIV-D 2.2 uses specified oil. Please confirm the specification in owner's manual. If
engine oil other than the specified oil is used, the Diesel Particulate Filter
effective period of
use will be shortened or the Diesel Particulate Filter may be damaged.
NOTE
(SKYACTIV-G 2.0 and SKYACTIV-G 2.5)
•It is normal for all engines to consume engine oil under normal driving conditions.
Engine oil consumption may be as high as 0.8 L/1,000 km (1 L/800 miles). This may be as
a result of evaporation, internal ventilation or burning of the lubricating oil in the
working engine. Oil consumption may be high er when the engine is new due to the
running-in process. Oil consumption is also dependant on engine speed and engine load.
Under extreme driving conditions, oil consumption may be higher.
(SKYACTIV-D 2.2)
•Whenever the engine oil is replaced, the vehicles engine control unit needs to be reset as
soon as possible. Otherwise the wrench indi cator light or engine oil warning light may
turn on. To reset the engine control unit, consult an expert repairer, we recommend an
Authorised Mazda Repairer or refer to the vehicle engine control unit reset procedure on
page 6-27.
•Inspect the engine oil level periodically. When inspecting the engine oil, if the engine oil
level is exceeds the “X” mark on the dipstick, replace the engine oil. This should be done
by an expert repairer, we recommend an Authorised Mazda Repairer. When replacing the
engine oil, inspect the oil level using the oil dipstick and refill so that the engine oil level
is within the range between MIN and MAX as shown in the figure.
X Mark
MAX
MIN
▼ Vehicle Engine Control Unit Reset Procedure
NOTE
This procedure is intended for vehicles
with SKYACTIV-D 2.2 and vehicles with
SKYACTIV-G 2.0 or SKYACTIV-G 2.5 which the engine oil flexible maintenance setting is
selected.
After replacing the engine oil, have a repair shop such as an A uthorised Mazda Repairer
perform the initialization (engine oil data resetting) of the r ecorded value. If the value
recorded by the computer is not initialized, the wrench indicat or light may not turn off or it
may turn on earlie r than normal.
Maintenance and Care
Owner Maintenance
6-27
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2
NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the instrument panel illumination knob pressed, and press and hold the instrument panel illumination knob for about 5 seconds until the master
warning light
flashes.
Instrument panel illumination knob
3. After the master warning light flashes for several seconds, the initialization is
completed.
▼ Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal operating temperature.
3. Turn it off and wait at least 5 minutes for the oil to return to the sump.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
SKYACTIV-G 2.0 and
SKYACTIV-G 2.5
MAX
OK
MIN
Maintenance and Care
Owner Maintenance
6-28
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2
