2017 MAZDA MODEL CX-5 inflation pressure

NOTE
Do not throw away the empty tyre
sealant bottle after use. Return the
empty tyre sealant bottle to an
Authorised Mazda Repairer when
replacing the tyre. The empty tyre
sealant bottle will need to be used to
extract and dispose of the used sealant
from the tyre.
12. Adhere the speed restriction sticker to
the speedometer.

WA R N I N G
Attach the speed restriction sticker in a
place where it can be viewed easily by
the driver:
Applying the speed restriction sticker
to the steering wheel is dangerous as
it could interfere with the air bag
deployment and result in serious
injury.
 Do not apply the sticker to any
position other than the position
indicated in the illustration of the
speedometer.
13. Install the compressor hose to the tyre
valve.

Valve Compressor hose
14. Insert the compressor plug into theinterior accessory socket and switch
the ignition to A CC (page 5-144).

Compressor plug
Compressor
Centre console
CAUTION
Before pulling out the compressor
plug from the electrical socket, make
sure the compressor power switch is
off.
 The compressor turns on and
off with
the push-button switch.
15. Turn the compressor switch on and inflate the tyre carefully to the correct
inflation pressure.
If Trouble Arises
Flat Tyre
7-23
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

WARNING
Never operate the compressor above
300 kPa (3.1 kgf/ c m
2, 3 bar, 43.5 psi):
Operating the compressor above 300
kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi) is
dangerous. When the inflation pressure
rises above 300 kPa (3.1 kgf/cm
2, 3 bar,
43.5 psi), heated air will be exhausted
from the back of the compressor and
you could be burned.
NOTE
•Check the tyre inflation pressure
label (driver's door frame) for the
correct tyre inflation pressure.
•Do not use the compressor for
longer than 10 minutes because
using the compressor for long
periods could damage it.
•If the tyre does not inflate, repair of
the tyre may not be possible. If the
tyre does not reach the correct
inflation pressure within a 10-minute
period, it probably has received
more extensive damage. When this
happens, the emergency flat tyre
repair kit cannot be used to repair
the tyre. Contact an expert repairer,
we recommend an Authorised Mazda
Repairer.
•If the tyre has been over-inflated,
loosen the screw cap on the
compressor and bleed some of the
air out.
16. When the tyre has been inflated to the proper inflation pressure, turn the
compressor switch off and remove the
compressor hose from the tyre valve.
17. Install the tyre valve cap.
18. Put the emergency flat tyre repair kit in the boot and continue driving.
CAUTION
Drive carefully to an expert repairer,
we recommend an Authorised
Mazda Repairer and keep the vehicle
speed below 80 km/h (50 mph).
 If the vehicle is driven 80 km/h (50
mph) or higher, the vehicle might
begin to vibrate.
NOTE
(With Tyre Pressure Monitoring
System)
If the tyre is not properly inflated, the
tyre pressure monitoring system
warning light will illuminate (page
4-42).
19. After driving the vehicle for 10 minutes or 5 km (3 miles), check the
tyre pressure with the tyre pressure
gauge equipped with the compressor. If
the tyre pressure ha s fallen below the
correct tyre pressure, inflate the tyre to
the correct pressure again following
the steps from number 14.
CAUTION
 If the tyre inflation pressure falls
below 130 kPa (1.3 kgf/cm
2 or bar,
18.9 psi), repair cannot be done with
the repair kit. Park the vehicle on a
level surface off the right-of-way and
contact an expert repairer, we
recommend an Authorised Mazda
Repairer.
If Trouble Arises
Flat Tyre
7-24
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

If the tyre
inflation pressure continues
to remain low after repeating steps
13 to 20, park the vehicle on a level
surface off the right-of-way and
contact an expert repairer, we
recommend an Authorised Mazda
Repairer.
NOTE
When checking the tyre inflation
pressure with the tyre pressure gauge
on the compressor unit, make sure the
compressor switch is turned off.
20. The emergency flat tyre repair is
completed if the tyre air pressure does
not decrease. Drive the vehicle
carefully to the nearest expert repairer,
we recommend an Authorised Mazda
Repairer promptly and have the tyre
replaced. Mazda recommends that the
tyre be replaced with a new one. If the
tyre is to be repaired and reused,
consult an expert repairer, we
recommend an Authorised Mazda
Repairer.
Peel off the speed restriction sticker
after replacing the tyre.
CAUTION
For a tyre which has undergone an
emergency flat tyre repair using the
emergency
flat tyre repair kit, Mazda
recommends that the tyre be
replaced with a new one as soon as
possible. If the tyre is to be repaired
and reused, consult an expert
repairer, we recommend an
Authorised Mazda Repairer.
 The wheel can be reused after any
sealant adhering to it is wiped off
and carefully inspected. However,
replace the tyre valve with a new one.
▼ Inspecting the Emergency Flat Tyre
Repair Kit
Inspect the emergency flat tyre repair kit at
regular intervals.
•Check the tyre sealant period of
effective use.
•Check the operation of the tyre
compressor.
NOTE
The tyre sealant has a period of effective
use. Check the period of effective use
indicated on the bottle label and do not
use it if it has expired. Have the tyre
sealant replaced at an Authorised Mazda
Repairer before the period of effective use
has expired.
If Trouble Arises
Flat Tyre
7-25
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

3. Install the wheel nuts with the bevellededge inward; tighten them by hand.

WARNING
Do not apply oil or grease to wheel nuts
and bolts and do not tighten the wheel
nuts beyond the recommended
tightening torque:
Applying oil or grease to wheel nuts
and bolts is dangerous. The wheel nuts
could loosen while driving and cause
the tyre to come off, resulting in an
accident. In addition, wheel nuts and
bolts could be damaged if tightened
more than necessary.
4. Turn the wheel brace anticlockwise and lower the vehicle.
5. Use the wheel brace to tighten the nuts in the order shown.

If you are unsure of how tight the nuts
should be, have them inspected at an
expert repairer, we recommend an
Authorised Mazda Repairer.
Nut tightening torque
N·m (kgf·m, ft·lbf) 108―147 (12―14,
80―108)
WARNING
Always securely and correctly tighten
the wheel nuts:
Improperly or loosely tightened wheel
nuts are dangerous. The wheel could
wobble or come off. This could result in
loss of vehicle control and cause a
serious accident.
Be sure to reinstall the same nuts you
removed or replace them with metric
nuts of the same configuration:
Because the wheel studs and wheel
nuts on your Mazda have metric
threads, using a non-metric nut is
dangerous. On a metric stud, it would
not secure the wheel and would
damage the stud, which could cause
the wheel to slip off and cause an
accident.
6. Remove the tyre blocks and store the tools and jack.
7. Store the damaged tyre in the luggage compartment.
8. Check the inflation pressure. Refer to Tyres on page 9-9.
9. Have the flat tyre repaired or replaced as soon as possible.
If Trouble Arises
Flat Tyre
7-30
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Action to be taken
Inspect the tyres and adjust to the specified inflation pressur e (page 6-43).
CAUTION
When replacing/repairing the tyres or wheels or both, have the work done by an Authorised Mazda Repairer, or
the tyre pressure sensors may be damaged.
NOTE
•Perform tyre pressure adjustment when the tyres are cold. Tyre pressure will vary according to the tyre temper-
ature, therefore let the vehicle stand for 1 hour or only drive it 1.6 km (1 mile) or less before adjusting the tyre
pressures. When pressure is adjusted on hot tyres to the cold inflation pressure, the TPMS warning light/beep
may turn on after the tyres cool and pressure drops below specification.
Also, an illuminated TPMS warning light, resulting from th e tyre air pressure dropping due to cold ambient
temperature, may turn off if the ambien t temperature rises. In this case, it will also be necessary to adjust the
tyre air pressures. If the TPMS warn ing light illuminates due to a drop in tyre air pressure, make sure to check
and adjust the tyre air pressures.
•After adjusting the tyre air pressures, it may require some time for the TPMS warning light to turn off. If the
TPMS warning light remains illuminated, drive the vehicle at a speed of at least 25 km/h (16 mph) for 10 mi-
nutes, and then verify that it turns off.
•Tyres lose air naturally over time and the TPMS cannot tell if the tyres are getting too soft over time or you
have a flat. However, when you find one low tyre in a se t of four-that is an indication of trouble; you should
have someone drive the vehicle slowly forward so you can inspect any low tyre for cuts and any metal objects
sticking through tread or sidewall. Pu t a few drops of water in the valve stem to see if it bubbles indicating a
bad valve. Leaks need to be addresse d by more than simply refilling the trouble tyre as leaks are dangerous ―
take it to an expert repairer, we recommend an Authoris ed Mazda Repairer which has all the equipment to fix
tyres, TPMS systems and order the best replacement tyre for your vehicle.
If the warning light illuminates again even after the tyre pressures are adju sted, there may be a tyre puncture.

If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-57
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼i-stop Warning Beep*
•If the driver's door is opened while
engine idling is sto
pped, the warning
sound operates to notify the driver that
engine idling is sto pped. It stops when
the driver's door is closed.
•(European model)
The warning sound operates if the
following operations are performed
while the engine id ling is stopped. In
such cases, the engine does not restart
automatically to ensure safety. Start the
engine using the normal method.
•(Manual transaxle)
With the shift lever in a position other
than neutral, the dri ver's seat belt is
unfastened and the driver's door is
opened.
•(Automatic transaxle)
With the selector lever in the D or M
(not in second gear fixed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
▼ Vehicle Speed Alarm*
The vehicle speed alarm function is
designed to alarm the driver via a single
beep sound and a warning indication in the
instrument cluster that the previously set
vehicle speed has been exceeded.
You can change the vehicle speed setting
at which the warning is triggered.
▼120 km/h Warning Beep*
If the vehicle speed exceeds 120 km/h, a
chime sounds for 5 seconds.
▼ Electric Parking Brake (EPB)
Warning Beep
The warning buzzer is activated under the
following conditions:
•The vehicle is driven with the electric
parking brake (EPB) applied.
•The electric parking
brake (EPB) switch
is pulled while the vehicle is driven.
▼ AUTOHOLD Warning Beep
Warning light flashes/m
essage is displayed
and beep sound is activated
simultaneously for about five seconds
when using AUTOHOLD function or
when AUTOHOLD swi tch is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.

If the warning light flashes/message is
displayed and the beep sound is activated
simultaneously, have your vehicle
inspected at an expert repairer, we
recommend an Authorised Mazda
Repairer.
▼ Power Steering Warning Buzzer
If the power steer
ing system has a
malfunction, the power steering
malfunction light turns on or flashes and
the buzzer operates at the same time.
Refer to Warning Indication/Warning
Lights on page 4-42.
▼ Tyre Inflation Pressure Warning
Beep*
The warning beep sound will be heard for
about 3 seconds if the tyre pressures
decrease.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-66*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Tyre mark information
Choose the proper tyres for your vehicle using the following tyre mark information.
Speed symbolMaximum permissible speed
Q Up to 160 km/h (99 mph)
R Up to 170 km/h (105 mph)
S Up to 180 km/h (111 mph)
T Up to 190 km/h (118 mph)
U Up to 200 km/h (124 mph)
H Up to 210 km/h (130 mph)
V Up to 240 km/h (149 mph)
W Up to 270 km/h (167 mph)
Y Up to 300 km/h (186 mph)
ZR Over 240 km/h (149 mph)
Tyre and inflation pressure
NOTE
The tyres have been optimally matched with the chassis of your vehicle.
When replacing tyres, Mazda recommends that you replace tyres of the same type originally
fitted to your vehicle. For details, contact an expert repairer, we recommend an Authorised
Mazda Repairer .
Check the tyre pressure label for tyre size and inflation press ure page 6-43.
Standard tyre
(Except Malaysia, Tha iland, Indonesia)
Ty r e s i z e Inflation pressure
Up to 3 persons ―Full load
225/65R17 102V Front
230 kPa (2.3 bar, 33 psi) 260 kPa (2.6 bar, 38 psi)
Rear 230 kPa (2.3 bar, 33 psi) 280 kPa (2.8 bar, 41 psi)
225/55R19 99V Front
250 kPa (2.5 bar, 36 psi) 260 kPa (2.6 bar, 38 psi)
Rear 250 kPa (2.5 bar, 36 psi) 290 kPa (2.9 bar, 42 psi)
Specifications
Specifications
9-10
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

(Malaysia, Thailand, Indonesia)
Ty re s i z eInflation pressure
Up to 3 persons ―Full load
225/65R17 102H
*1Front 240 kPa (2.4 bar, 35 psi) 260 kPa (2.6 bar, 38 psi)
Rear 240 kPa (2.4 bar, 35 psi) 280 kPa (2.8 bar, 41 psi)
225/55R19 99V Front
250 kPa (2.5 bar, 36 psi) 260 kPa (2.6 bar, 38 psi)
Rear 250 kPa (2.5 bar, 36 psi) 290 kPa (2.9 bar, 42 psi)
1 person's weight: About 75 kg*1 SKYACTIV-G 2.0, SKYACTIV-G 2.5
Temporary spare tyre*
Tyre size Inflation pressure
185/80R17 99M 320 kPa (3.2 bar, 46 psi)
T145/90D16 106M 420 kPa (4.2 bar, 60 psi)
Winter tyre
Ty re s i z eInflation pressure
Up to 3 persons ―Full load
225/65R17
*1 MS Front
230 kPa (2.3 bar, 33 psi) 260 kPa (2.6 bar, 38 psi)
Rear 250 kPa (2.5 bar, 36 psi) 300 kPa (3.0 bar, 44 psi)
225/55R19
*2 MS Front
250 kPa (2.5 bar, 36 psi) 260 kPa (2.6 bar, 38 psi)
Rear 270 kPa (2.7 bar, 39 psi) 310 kPa (3.1 bar, 45 psi)
1 person's weight: About 75 kg*1 Load index and Speed Symbol: 102Q/102S/102H/102V*2 Load index and Speed Symbol: 99Q/99S/99H/99V
Wheel nut tightening torque
When installing a tyre, tighten the wheel nut to the following torque.
108―147 N·m (12―14 kgf·m, 80―108 ft·lbf)
▼ Fuses
Refer to Fuses on page 6-54.
▼Brakes
If you require information regarding the wear limit specificati
on for the brake disc plates
and the measurement method, please contact an expert repairer, we recommend an
Authorised Mazda Repairer. The information is made freely avail able.
Specifications
Specifications
*Some models.9-11
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2