2017 MAZDA MODEL CX-5 ignition

How to set the distance-between-vehicles during headway control
The distance-between-vehicles is set to a shorter distance by pressing the switch. The
distance-between-vehicles is set to a longer distance by pressi ng the
switch. The
distance-between-vehicles can be set to 4 levels; Long, medium, short, and extremely short
distance.
Distance-between-vehicles guide-
line
(at 80 km/h (50 mph) vehicle
speed) Indication on multi-information
display Indication on active driving dis-
play
*1
Long (about 50 m (164 ft))
Medium (about 40 m (131 ft))
Short (about 30 m (98 ft))
Extremely short (about 25 m (82 ft))
*1 Displays a pop-up image in the a ctive driving display only when the driver operates the switch.
NOTE
•The distance-between-vehicles differs depending on the vehicle speed, and the slower the
vehicle speed, the shorter the distance.
•When the ignition is switched to ACC or OFF and then the engine is started again, the
system automatically sets the distance-between-vehicles to the previous setting.
When Driving
i-ACTIVSENSE
4-143
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
•If the ignition is switched off while the MRCC with Stop & Go function system is
operating, the system will be operable when the ignition is switched ON the next time.
•(European models)
When the MODE switch is pressed a second time while the MRCC with Stop & Go
function system is operating, the system switches to the Adjustable Speed Limiter (ASL).
Refer to Adjustable Speed Limiter (ASL) on page 4-174.
•(Except European models)
When the MODE switch is pressed a second time while the MRCC with Stop & Go
function system is operating, the system switches to the cruise control function.
Refer to Cruise Control Function on page 4-160.
How to set the speed
1. Adjust the vehicle speed to the desired setting using the acc elerator pedal.
2. Headway control begins when the SET
or SET switch is pressed.
The set speed and the inter-vehicle distance display filled with white lines is displayed.
The MRCC with Stop & Go function main indication (white) switch es to the MRCC
with Stop & Go function set indi cation (green) at the same time.
Tr a v e l s t a t u sIndication on multi-information
display Indication on active driving dis-
play
During travel at constant speed
During travel under headway con-
trol
When Driving
i-ACTIVSENSE
4-155
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Distance-between-vehicles guide-line
(at 80 km/h (50 mph) vehicle speed) Indication on multi-information
display Indication on active driving dis-
play
*1
Extremely short (about 25 m (82 ft))
*1 Displays a pop-up image in the a ctive driving display only when the driver operates the switch.
NOTE
•The distance-between-vehicles differs depending on the vehicle speed, and the slower the
vehicle speed, the shorter the distance.
•When the ignition is switched to ACC or OFF and then the engine is started again, the
system automatically sets the distance-between-vehicles to the previous setting.
How to change the set vehicle speed
To accelerate/decelerate using the SET
switch
When you press the SET
switch, the
vehicle accelerates and when you press the
SET
switch, it decelerates.
European
models Except Euro-
pean models
Short press 1 km/h (1 mph) 5 km/h (5 mph)
Long press 10 km/h (5 mph)
NOTE
For example, the set vehicle speed is
changed by pressing the SET switch four
times as follows:
(European models)
The vehicle speed accelerates or
decelerates by 4 km/h (4 mph).
(Except European models)
The vehicle speed accelerates or
decelerates by 20 km/h (20 mph).
To increase speed using accelerator
pedal
Depress the accelerator pedal and press
and release the SET
switch or SET
switch at the desired sp eed. If the switch is
not operated, the syste m returns to the set
speed after you release your foot from the
accelerator pedal.
CAUTION
The warnings and brake control do not
operate while the accelerator pedal is
depressed.
NOTE
•The setting speed can be changed by
operating the SET
switch or SET
switch during stop hold control.
When Driving
i-ACTIVSENSE
4-157
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼System Cancelling
When the LAS&LDWS is turned off,
press the LAS&LDWS OFF switch.
The LAS&LDWS OFF indicator light
turns on.
NOTE
•In the following cases, the LAS&LDWS
is cancelled automatically and the
LAS&LDWS OFF indication is
displayed in the multi-information
display. Have your vehicle inspected at
an expert repairer, we recommend an
Authorised Mazda Repairer.
•There is a malfunction in the power
steering.
•There is a malfunction in the TCS.
•There is a malfunction in the Forward
Sensing Camera (FSC).
(European models)
•When the ignition is switched OFF, the
LAS&LDWS becomes operational the
next time the ignition switched ON.
(Except European models)
•When the ignition is switched OFF, the
system status before it was turned off is
maintained. For examp le, if the ignition
is switched OFF with the lane-keep
system operable, the system will be
operable when the ignition is switched
ON the next time.
When the LAS&LDWS is turned off, the
vehicle lane line indication in the
multi-information display and the active
driving display turn off.
When Driving
i-ACTIVSENSE
4-171
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

CAUTION
(With cruise control)
If the set speed is set lower than the current vehicle speed by pressing the SET
or RES/
switch, the warning beep is not activated for about 30 seconds even if the vehicle speed is
faster than the newly set speed by 5 km/h (3 mph). Be careful not to drive over the set speed.
(With Mazda Radar Cruise Control (MRCC) or Mazda Radar Cruise Control with Stop & Go
function (MRCC with Stop & Go function))
If the set speed is set lower than the current vehicle speed by pressing the SET
or RES switch,
the warning beep is not activated for about 30 se conds even if the vehicle speed is faster than
the newly set speed by 5 km/h (3 mph). Be careful not to drive over the set speed.
NOTE
When the system is temporarily cancelled by depressing the accelerator pedal fully, the ASL
display shows the cancel display. If the vehicle speed exceeds the set speed by about 5 km/h
(3 mph) or more while the cancel display is displayed, the set speed display flashes but the
warning sound is not operated.
▼ Activation/Deactivation
NOTE
When the ignition is switched of
f, the system status before it was turned off is maintained.
For example, if the ignition is switched off while the ASL is operating, the system will be
operable when the ignition is switched ON the next time.
Activation
Press the MODE switch to operate the system. The ASL screen is displayed, and the ASL
main indication displays in white.
NOTE
When the cruise control, Mazda Radar Cruise Control (MRCC), or Mazda Radar Cruise
Control with Stop & Go function (MRCC with Stop & Go function) system becomes
operable after pressing the MODE switch, press the mode switch again to switch to the ASL.
Deactivation
To deactivate the system, do the following operations:
When a cruising speed h as been set (ASL set indication displays in green)
Long-press the OFF/CAN switch or press the OFF/CAN switch 2 times. The ASL screen is
no longer displayed and the ASL set indication (green) does not display.
When Driving
i-ACTIVSENSE
4-178
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Smart Brake Support (SBS)*
The SBS system alerts the driver of a possible collision using a display and warning sound
if the radar sensor (front) and the Forward Sens ing Camera (FSC) determine that there is the
possibility of a collision with a vehicle ahead while the vehicle is being driven at about 15
km/h or faster (10 mph or faster). Furthermore, if the radar se nsor (front) and the Forward
Sensing Camera (FSC) determines that a collision is unavoidable, the automatic brake
control is performed to reduce d amage in the event of a collision.
In addition, when the driver depresses the brake pedal, the bra kes are applied firmly and
quickly to assist. (Brake Assist (SBS brake assist))
WA R N I N G
Do not rely completely on the SBS system and always drive carefully:
The SBS is designed to reduce damage in the ev ent of a collision, not avoid an accident. The
ability to detect an obstruction is limited de pending on the obstruction, weather conditions,
or traffic conditions. Therefore, if the accelerator pe
dal or brake pedal is mistakenly operated
it could result in an accident. Always verify th e safety of the surrounding area and depress the
brake pedal or accelerator pedal while keepin g a safer distance from vehicles ahead or
on-coming vehicles.
CAUTION
In the following cases, turn the system off to prevent a mis-operation:
 The vehicle is being towed or when towing another vehicle.
 The vehicle is on a chassis roller.
 When driving on rough roads such as in areas of dense grass or
off-road.
NOTE
•The SBS system operates when all of the following conditions are met:
•The ignition is switched ON.
•The SBS system is on.
•The vehicle speed is about 15 km/h or faster (10 mph or faster).
•The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
•The Dynamic Stability Control (DSC) is not operating.
•The SBS system may not operate under the following conditions:
•If the vehicle is accelerated rapidly and it comes cl ose to a vehicle ahead.
When Driving
i-ACTIVSENSE
*Some models.4-193
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the ignition is
switched OFF with the cruise control
system operable, the system will be
operable when the ignition is switched ON
the next time.
▼To Set Speed
1.
(With Adjustable Speed Limiter
(ASL))
Activate the cruise control system by
pressing the MODE switch. The cruise
main indication (wh ite) is displayed.
(Without Adjustabl e Speed Limiter
(ASL))
Activate the cruise control system by
pressing the ON switch. The cruise
main indication (wh ite) is displayed.
2. Accelerate to the desired speed, which
must be more than 25 km/h (16 mph).
3. Set the cruise control by pressing the
SET
switch at the desired speed. The
cruise control is set at the moment the
SET
switch is pressed. Release the
accelerator pedal simultaneously. The
cruise set indication (green) is
displayed.
NOTE
•The cruise control speed setting cannot
be performed under the following
conditions:
•(Automatic transaxle)
The selector lever is in the P or N
position.
•(Manual transaxle)
The shift lever is in the neutral
position.
•The parking brake is applied.
•(Vehicles with Adjustable Speed
Limiter (ASL))
The MODE switch for the Adjustable
Speed Limiter (ASL) is pressed.
•Release the SET or RES/ switch at
the desired speed, otherwise the speed
will continue increasing while the RES/
switch is pressed and held, and
continue decreasing while the SET
switch is pressed and held (except when
the accelerator pedal is depressed).
•On a steep grade, the vehicle may
momentarily slow down while
ascending, or speed up while
descending.
•The cruise control will cancel if the
vehicle speed decreases below 21 km/h
(13 mph) when climbing a steep grade.
•The cruise control may cancel at about
15 km/h (9 mph) below the preset speed
such as when climbing a long, steep
grade.
When Driving
Cruise Control
4-209
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Tyres and Wheels
CAUTION
When inspecting or adjusting the tyre air
pressures, do not apply excessive force to
the stem part of the wheel unit. The stem
part could be damaged.
Changing tyres and wheels
The following procedure allows the TPMS
to recognise a tyre pressure sensor's
unique ID signal code whenever tyres or
wheels are changed, such as changing to
and from winter tyres.
NOTE
Each tyre pressure sensor has a unique ID
signal code. The signal code must be
registered with the TPMS before it can
work. The easiest way to do it is to have
an Authorised Mazda Dealer change your
tyre and complete ID signal code
registration.
When having tyres changed at an
Authorised Mazda Dealer
When an Authorised Mazda Dealer
changes your vehicle's tyres, they will
complete the tyre pressure sensor ID
signal code registration.

When changing
tyres yourself
If you or someone else changes tyres, you
or someone else can also undertake the
steps for the TPMS t o complete the ID
signal code registration.
1. After tyres have been changed, switch
the ignition ON, then back to ACC or
OFF.
2. Wait for about 15 minutes.
3. After about 15 minutes, drive the vehicle at a speed of at least 25 km/h
(16 mph) for 10 minutes and the tyre
pressure sensor ID s ignal code will be
registered automatically.
NOTE
If the vehicle is driven within about 15
minutes of changing tyres, the tyre
pressure monitoring system warning light
will flash because the sensor ID signal
code would not have been registered. If
this happens, park the vehicle for about 15
minutes, after which the sensor ID signal
code will register upon driving the vehicle
for 10 minutes.
Replacing tyres and wheels
CAUTION
 When replacing/repairing the tyres or
wheels or both, have the work done by
an Authorised Mazda Dealer, or the tyre
pressure sensors may be damaged.
 The wheels equipped on your Mazda are
specially designed for installation of the
tyre pressure sensors. Do not use
non-genuine wheels, otherwise it may
not be possible to install the tyre pressure
sensors.
Be sure to have the ty re pressure sensors
installed whenever tyres or wheels are
replaced.
When having a tyre or wheel or both
replaced, the follow ing types of tyre
pressure sensor installations are possible.
•The tyre pressure sensor is removed
from the old wheel and installed to the
new one.
When Driving
Tyre Pressure Monitoring System
4-214
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2