2017 MAZDA MODEL CX-3 height adjustment

2–4
Essential Safety Equipment
Seats
CAUTION
  When operating a seat, be careful not to put your hands or ¿ ngers near the moving
parts of the seat or on the side trim to prevent injury.
  When moving the seats, make sure there is no cargo in the surrounding area. If the
cargo gets caught it could damage the cargo.
  (Manual Seat)  When moving the seats forward and rearward or returning a rear-reclined seatback
to its upright position, make sure you hold onto the seatback with your hand while
operating. If the seatback is not held, the seat will move suddenly and could cause
injury.
NOTE
  When returning a rear seat to its original position, place the seat belt in its normal
position. Verify that the seat belt pulls out and retracts.
 
 (Power Seat)  The seat-bottom power adjustment is operated by motors. Avoid extended operation
because excessive use can damage the motors.
 


 To prevent the battery from running down, avoid using the power adjustment when
the engine is stopped. The adjuster uses a large amount of electrical power.
 


 Do not use the switch to make more than one adjustment at a time.

 
 When getting in and out of the vehicle, your foot could accidentally contact the seat
height adjustment lever and cause the seat to lower.
 Adjust the seat to obtain the correct driving position.

2–5
Essential Safety Equipment
Seats
*Some models.
Front Seat
Seat Operation

Power operation


Seat Slide
(Manual Seat)
To move a seat forward or backward, raise the lever and slide the seat to the desired position
and release the lever.
Make sure the lever returns to its original position and the seat is locked in place by
attempting to push it forward and backward.
(Power Seat)
To slide the seat, move the slide lifter switch on the outside of the seat to the front or back
and hold it. Release the switch at the desired position.

Height Adjustment *

(Manual Seat)
To adjust the seat height, move the lever up or down.
(Power Seat)
To adjust the seat height, move the switch up or down.

Height Adjustment for Front Edge of Seat Bottom (Driver's Power Seat)
To adjust the front height of the seat bottom, raise or lower the front of the slide lifter
switch.

2–7
Essential Safety Equipment
Seats
*Some models.
Driving Position Memory *
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
 


 Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
  Refer to Seat Operation on page 2-5 .



 Active driving display (display position,
brightness level, display information)
  Refer to Active Driving Display on page
4-33 .

CAUTION
Do not place ¿ ngers or hands around
the bottom of the seat while the seat
memory function is operating. The
seat moves automatically while the
seat memory function is operating and
¿ ngers or hands could get pinched and
injured.

SET button

The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
  Lumbar support adjustment cannot
be programmed.
  Individual seat positions can be
programmed to the two available
programming buttons on the side
of the driver's seat, plus one seat
position for each registered key.
  If the vehicle has been serviced and
the battery leads disconnected, the
programmed seat positions will have
been erased. Re-programme the seat
positions.
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings
within 5 seconds of completing step 5
above:
 

 
 Programming using a button on
the side of the seat

 Press the button you want to
programme, either button 1 or 2, until
a beep sound is heard one time.
 

 
 Programming using the key 
 Press the key button until a beep
sound is heard one time.

NOTE
If a beep sound is heard three times, the
operation is cancelled.

2–13
Essential Safety Equipment
Seats
Head Restraints
Your vehicle is equipped with head
restraints on all outboard seats and the
rear centre seat. The head restraints are
intended to help protect you and the
passengers from neck injury.
WARNING
Always drive with the head restraints
installed when seats are being used and
make sure they are properly adjusted.
In addition, always raise the head
restraints on all rear seat when they are
being used:
Driving with the head restraints
adjusted too low or removed is
dangerous. With no support behind
your head, your neck could be seriously
injured in a collision.
Height Adjustment
Adjust the head restraint so that the centre
is even with the top of the passenger's ears.



To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the stop-
catch release, then push the head restraint
down.
Front outboard seat



Rear outboard seat



Rear centre seat

4–35
When Driving
Instrument Cluster and Display
 


 Speed limit indicator (vehicles with navigation system) 



 Vehicle Speed
Each setting/adjustment for the active driving display can be performed on the centre
display.

1. Select the icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
 

 
 Method for adjusting screen brightness (automatically/manually)


 
 Screen brightness initial settings (automatic adjustment is selected)


 
 Screen brightness adjustment (manual adjustment is selected)


 
 Display position of active driving display (display height)


 
 Active driving display angle adjustment (display angle correction)


 
 Turn by turn (TBT) display/non-display (navigation guidance)


 
 Street name display timing can be changed (navigation guidance)


 
 Active driving display ON/OFF (indication)


 
 Reset settings (reset)
NOTE

 The desired driving position (display position, brightness level, display information)
can be called up after programming the position.
 Refer to Driving Position Memory on page 2-7 .   The street name may not be displayed depending on the market and region.

9–17
Speci¿ cations
Personalisation Features
Item Feature Factory
Setting Available
Settings Settings
Change
Method


Active Driving Display (page 4-33 )
Display Setting can be changed so that the Active
Driving Display is not displayed. On On/Off C —


The display height (up/down position) can be
changed. 0 13 steps up/
down from
initial setting
(total: 27
steps) C —


The method for adjusting the display
brightness (automatically/manually) can be
changed. AUTO AUTO/
MANUAL C —


The standard brightness while automatic
adjustment is selected can be changed using
the brightness adjustment. 0 2 steps up/
down from
initial setting
(total: 5
steps) C —


The standard brightness while manual
adjustment is selected can be changed using
the brightness adjustment. 0 20 steps up/
down from
initial setting
(total: 41
steps) C —


Navigation guidance The display information can be changed. Adaptive
Lane/Street/
Turn Adaptive
Lane/Street/
Turn
Lane
Guidance &
Turn by Turn
Street Name
& Turn by
Turn
OFF C —


*1 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda recommends
that these systems remain On.
*2 For vehicles with an audio system other than the on-screen function type, the warning sound cannot be changed.
The warning sound is only a beep.
*3 Only the volume of the warning beep during Blind Spot Monitoring (BSM) operation can be changed. The
volume of the warning beep during Rear Cross Traf¿ c Alert (RCTA) operation cannot be changed.
*4 This system functions only when the navigation system is functioning.
*5 If the auto-wiper control is set to Off, the wiper lever
position is set to intermittent operation.
*6 The operation may stop in 15 minutes due to the effect of the outside temperature even if the operation time of
the rear window defogger has been changed to Continuous.
*7 Available only in display from the centre display.