2017 MAZDA MODEL CX-3 driver seat adjustment

2–5
Essential Safety Equipment
Seats
*Some models.
Front Seat
Seat Operation

Power operation


Seat Slide
(Manual Seat)
To move a seat forward or backward, raise the lever and slide the seat to the desired position
and release the lever.
Make sure the lever returns to its original position and the seat is locked in place by
attempting to push it forward and backward.
(Power Seat)
To slide the seat, move the slide lifter switch on the outside of the seat to the front or back
and hold it. Release the switch at the desired position.

Height Adjustment *

(Manual Seat)
To adjust the seat height, move the lever up or down.
(Power Seat)
To adjust the seat height, move the switch up or down.

Height Adjustment for Front Edge of Seat Bottom (Driver's Power Seat)
To adjust the front height of the seat bottom, raise or lower the front of the slide lifter
switch.

2–6
Essential Safety Equipment
Seats
Seat Recline
(Manual Seat)
To change the seatback angle, lean forward slightly while raising the lever. Then lean back
to the desired position and release the lever.
Make sure the lever returns to its original position and the seatback is locked in place by
attempting to push it forward and backward.
(Power Seat)
To change the seatback angle, press the front or rear side of the reclining switch. Release the
switch at the desired position.

Lumbar Support Adjustment (Driver's Power Seat)
To increase the seat ¿ rmness, press and hold the front part of the switch to the desired
position, then release it.
Press the rear part of the switch to decrease ¿ rmness.

2–7
Essential Safety Equipment
Seats
*Some models.
Driving Position Memory *
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
 


 Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
  Refer to Seat Operation on page 2-5 .



 Active driving display (display position,
brightness level, display information)
  Refer to Active Driving Display on page
4-33 .

CAUTION
Do not place ¿ ngers or hands around
the bottom of the seat while the seat
memory function is operating. The
seat moves automatically while the
seat memory function is operating and
¿ ngers or hands could get pinched and
injured.

SET button

The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
  Lumbar support adjustment cannot
be programmed.
  Individual seat positions can be
programmed to the two available
programming buttons on the side
of the driver's seat, plus one seat
position for each registered key.
  If the vehicle has been serviced and
the battery leads disconnected, the
programmed seat positions will have
been erased. Re-programme the seat
positions.
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings
within 5 seconds of completing step 5
above:
 

 
 Programming using a button on
the side of the seat

 Press the button you want to
programme, either button 1 or 2, until
a beep sound is heard one time.
 

 
 Programming using the key 
 Press the key button until a beep
sound is heard one time.

NOTE
If a beep sound is heard three times, the
operation is cancelled.

2–8
Essential Safety Equipment
Seats
To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Press the programming button for the
driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving
position adjustment is completed.

NOTE
  If the driving position movement is
not changed, only the beep sounds.
  A seat position can be called up even
with the engine not running.
  The driving position adjustment is
cancelled in the following cases:
 


 Any of the seat adjustment
switches is operated.
 


 The SET button is pressed.



 Programming button 1 or 2 is
pressed.
 


 The key button or button is
operated.
 


 The vehicle starts moving.



 The active driving display is
adjusted. (Using a programmed key)
1. Unlock the doors by pressing a request
switch or the key
button.
2. After unlocking the doors, the seat
position adjustment begins within
40 seconds of opening the driver's door,
and a beep sounds when the operation
is ¿ nished.
3. Make sure the parking brake is on.
4. (Automatic transaxle)
Make sure the selector lever is in the P
position.
5. Start the engine.
6. The active driving display adjustment
begins.

NOTE
  If there is no driving position
movement, a beep is not heard.
  The driving position adjustment is
cancelled in the following cases:
 


 Any of the seat adjustment
switches is operated.
 


 The SET button is pressed.



 Programming button 1 or 2 is
pressed.
 


 The key button or button is
operated.
 


 The vehicle starts moving.



 The active driving display is
adjusted.