2017 MAZDA MODEL 2 air con

4–28
When Driving
Instrument Cluster and Display
NOTE
  (Vehicles with type B audio)  If the fuel economy data is reset
using the fuel economy monitor,
or trip A is reset using the trip
meter when the function which
synchronizes the fuel economy
monitor and the trip meter is on, the
fuel economy data and trip A are
reset simultaneously.
 Refer to Fuel Economy Monitor on
page 4-93 .
  Only the trip meters record tenths of
kilometres (miles).
  The trip record will be erased when: 



 The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


 The vehicle is driven over
9999.9 km (mile).
Trip Computer
The following information can be selected
by pressing the selector with the ignition
switched ON.
 


 Approximate distance you can travel on
the available fuel
 


 Current fuel economy
If you have any problems with your trip
computer, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy. The distance-to-empty will be calculated
and displayed every second.


NOTE
  Even though the distance-to-empty
display may indicate a suf¿ cient
amount of remaining driving distance
before refuelling is required, refuel
as soon as possible if the fuel level
is very low or the low fuel warning
light illuminates.
  The display may not change unless
you add more than approximately
9 L (2.3 US gal, 1.9 Imp gal) of fuel.
  The distance-to-empty is the
approximate remaining distance the
vehicle can be driven until all the
graduation marks in the fuel gauge
indicating the remaining fuel supply
disappear.
  If there is no past fuel economy
information such as after ¿ rst
purchasing your vehicle or the
information is deleted when the
battery leads are disconnected, the
actual distance-to empty/range may
differ from the amount indicated.

4–32
When Driving
Instrument Cluster and Display
*Some models.
Changing the Temperature Unit of the
Outside Temperature Display (Vehicles
with Type B)
The outside temperature unit can be
switched between Celsius and Fahrenheit.
Settings can be changed by operating the
centre display screen.
Refer to Personalisation Features on page
9-13 .
NOTE
When the temperature unit indicated
in the outside temperature display is
changed, the temperature unit indicated
in the engine coolant gauge display
changes in conjunction with it.
Outside Temperature Warning
*
When the outside temperature is low, the
indication À ashes and a beep sound is
heard to warn the driver of the possibility
of icy roads.
If the outside temperature is lower than
about 4 °C (39 °F), the outside temperature
display and the
mark À ashes for about
ten seconds and a beep sound is heard
once.
NOTE
If the outside temperature is lower than
-20 °C (-4 °F), the beep sound does not
operate. However, the
mark
illuminates.
Cruise Control Set Vehicle Speed
Display *
The vehicle speed preset using the cruise
control is displayed.



Adjustable Speed Limiter Display *
The setting status of the adjustable speed
limiter is displayed.



Trip Computer and INFO Switch *
The following information can be selected
by pressing the INFO switch with the
ignition switched ON.
 


 Distance-to-empty mode



 Average fuel economy mode



 Current fuel economy mode



 Average vehicle speed mode



 Vehicle speed alarm mode *
If you have any problems with your trip
computer, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.

4–39
When Driving
Instrument Cluster and Display
*Some models.
Signal Warning Page


(Red) High Engine Coolant Temperature Warning Light *1 7-35

Power Steering Malfunction Warning Light *1 7-35

Master Warning Light *1 7-38

Check Engine Light *1 7-38


(Amber) * i-stop Warning Light *1 7-38


(Amber) * i-ELOOP Warning Light 7-38

* Automatic Transaxle Warning Light *1 7-38

Air Bag/Seat Belt Pretensioner System Warning Light *1 7-38

* Tyre Pressure Monitoring System Warning Light *1 Flashing
7-38
Turns on
7-43


(Red) KEY Warning Light *1 Malfunction
7-38
Except malfunction
7-43


(Amber) * High Beam Control System (HBC) Warning Light *1 7-38


(Amber) * Adaptive LED Headlights (ALH) Warning Light *1 7-38

* Lane Departure Warning System (LDWS) Warning Light *1 Flashing
4-115
Turns on
7-38


(Amber) * Mazda Radar Cruise Control (MRCC) Warning Light 7-38

4–40
When Driving
Instrument Cluster and Display
*Some models.
Signal Warning Page

* LED Headlight Warning Light *1 7-38

Low Fuel Warning Light 7-43

Seat Belt Warning Light (Front seat) 7-43


(Red) * Seat Belt Warning Light (Rear seat) 7-43

* Door-Ajar Warning Light 7-43

* Low Washer Fluid Level Warning Light 7-43

* 120 km/h Warning Light *1 7-43


(Amber)
* Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning
Light *1 7-43
*1 The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or
when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an
expert repairer, we recommend an Authorised Mazda Repairer.
*2 The light turns on continuously when the parking brake is applied.

4–43
When Driving
Instrument Cluster and Display
*Some models.
Signal Indicator Lights Page

* Driver Attention Alert (DAA) Indication 4-129


(Green) * Mazda Radar Cruise Control (MRCC) Indicator Light 4-139


(Red)
* Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator
Light Smart City Brake
Support [Forward]
(SCBS F)
4-160
Smart City Brake
Support Reverse
(SCBS R)
4-165
Smart Brake Support
(SBS)
4-169


* Smart Brake Support/Smart City Brake Support (SBS/SCBS) OFF
Indicator Light Smart City Brake
Support [Forward]
(SCBS F)
4-160
Smart City Brake
Support Reverse
(SCBS R)
4-166
Smart Brake Support
(SBS)
4-169


(White) * Adjustable Speed Limiter Main Indication 4-150


(White/Green) * Adjustable Speed Limiter Set Indication/Indicator Light 4-150


(White) * Cruise Main Indication 4-186


(White/Green) * Cruise Set Indication/Indicator Light 4-186
*1 The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or
when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an
expert repairer, we recommend an Authorised Mazda Repairer.

4–44
When Driving
Instrument Cluster and Display
*Some models.
Wrench Indicator Light

When the ignition is switched ON, the
wrench indicator light turns on and then
turns off after a few seconds.

The wrench indicator light turns on
when the preset maintenance period
arrives. Verify the content and perform
maintenance.
Refer to Maintenance Monitor on page
6-15 .
SKYACTIV-D 1.5
The wrench indicator light turns on under
the following conditions:
 


 The engine oil has deteriorated.



 The engine oil level is around the MIN
mark on the dipstick or it is less than the
MIN mark.
*  


 The engine oil level is around the X
mark on the dipstick or it exceeds the X
mark.
*
Check the engine oil. Refer to Inspecting
Engine Oil Level on page 6-28 .
Replace the engine oil if the wrench
indicator light does not turn off even
though the engine oil level is in the normal
range.
NOTE
  Depending on the vehicle use
conditions, the wrench indicator light
may turn on for reasons other than
the preset maintenance period.
  Whenever the engine oil is replaced,
a reset of the vehicle engine control
unit is necessary.
 Your Authorised Mazda Repairer
will be able to reset the engine
control unit or see page 6-27 for
the Vehicle engine control unit reset
procedure.
Low Engine Coolant Temperature
Indicator Light (Blue)

The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been suf¿ ciently warmed
up, the temperature sensor could have a
malfunction. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.

4–50
When Driving
Automatic Transaxle
Shift-Lock System
The shift-lock system prevents shifting out
of P unless the brake pedal is depressed.

To shift from P:

1. Depress and hold the brake pedal.
2. Start the engine.
3. Press and hold the lock-release button.
4. Move the selector lever.

NOTE
  When the ignition is switched to
ACC or the ignition is switched off,
the selector lever cannot be shifted
from P.
  The ignition cannot be switched to
OFF if the selector lever is not in P.
Shift-Lock Override
If the selector lever will not move from P
using the proper shift procedure, continue
to hold down the brake pedal.
Ty p e A

1. Remove the shift-lock override cover
using a cloth-wrapped À at head
screwdriver.
2. Insert a screwdriver and push it down.


Cover
3. Press and hold the lock-release button.
4. Move the selector lever.

Take the vehicle to an expert repairer, we
recommend an Authorised Mazda Repairer
to have the system checked.
Ty p e B

1. Press the lock-release button with the
button pressed.

Lock-release button
button

2. Move the selector lever.

Take the vehicle to an expert repairer, we
recommend an Authorised Mazda Repairer
to have the system checked.

4–57
When Driving
Automatic Transaxle
WARNING
Do not use engine braking on slippery
road surfaces or at high speeds:
Shifting down while driving on wet,
snowy, or frozen roads, or while driving
at high speeds causes sudden engine
braking, which is dangerous. The
sudden change in tyre speed could
cause the tyres to skid. This could
lead to loss of vehicle control and an
accident.

Keep your hands on the steering wheel
rim when using ¿ ngers on the steering
shift switches:
Putting your hands inside the rim of
the steering wheel when using the
steering shift switches is dangerous. If
the driver's air bag were to deploy in a
collision, your hands could be impacted
causing injury.
NOTE
  When driving at high speeds, the
gear may not shift down.
  During deceleration, the gear may
automatically shift down depending
on vehicle speed.
  When depressing the accelerator
fully, the transaxle will shift to a
lower gear, depending on vehicle
speed. However, the gears do not
kickdown while the DSC is turned
off.
Second Gear Fixed Mode
When the selector lever is moved back
while the vehicle speed is about 10 km/h
(6.2 mph) or less, the transaxle is set in the
second gear ¿ xed mode. The gear is ¿ xed
in second while in this mode for easier
acceleration from a stop and driving on
slippery roads such as snow-covered
roads.
If the selector lever is moved back
or
forward
while in the second gear ¿ xed
mode, the mode will be cancelled.