2017 LEXUS RC200T tow

5747-3. Do-it-yourself maintenance
RC200t_RC F_EE(OM24728E)
■Rear turn signal lights
Open the trunk, remove the 2
covers and 2 screws and pull the
light unit toward the rear of the
vehicle to remove it.
When removing the cover, wrap the tip of the screwdriver with tape toprotect the vehicle from damage.
Turn the bulb base
counterclockwise.
Remove the light bulb.
Install a new light bulb then install
the bulb base to the light unit by
inserting it and turning the bulb
base clockwise.
After installing the light bulb, turn on
the rear turn signal light to visually check that there is no light leakingfrom the bulb base.
1
2
3
4

5757-3. Do-it-yourself maintenance
7
Maintenance and care
RC200t_RC F_EE(OM24728E)
Align the tabs and push the light
unit toward the front of the vehicle
to install it.
Install the 2 screws and 2 covers.
5
6

579
8When trouble arises
RC200t_RC F_EE(OM24728E)
8-1. Essential information
Emergency flashers ................. 580
If your vehicle has to be
stopped in an
emergency.................................. 581
8-2. Steps to take in an
emergency
If your vehicle needs to be
towed ...........................................582
If you think something is
wrong...........................................589
Fuel pump shut off
system ..........................................590
If a warning light turns
on or a warning buzzer
sounds........................................... 591
If a warning message is
displayed .................................... 597
If you have a flat tire
(vehicles with a
spare tire) .................................... 619
If you have a flat tire
(vehicles with an
emergency tire puncture
repair kit) .................................... 633
If the engine will not start ........ 648
If the electronic key does
not operate properly .............650
If the vehicle battery is
discharged ................................. 654
If your vehicle overheats ......... 659
If the vehicle becomes
stuck ............................................. 664

582
RC200t_RC F_EE(OM24728E)
8-2. Steps to take in an emergency
The following may indicate a problem with your transmission. Contact any
authorized Lexus dealer or repairer, or another duly qualified and equipped pro-
fessional or commercial towing service before towing.
●The engine is running but the vehicle does not move.
●The vehicle makes an abnormal sound.
If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle towed by any
authorized Lexus dealer or repairer , or another duly qualified and equipped
professional or commercial towing se rvice, using a wheel-lift type truck or
flatbed truck.
Use a safety chain system for all towing , and abide by all state/provincial and
local laws.
Situations when it is necessary to contact dealers before towing

5838-2. Steps to take in an emergency
8
When trouble arises
RC200t_RC F_EE(OM24728E)
Do not tow with a sling-type truck to
prevent body damage.
Towing with a sling-type truck
Towing with a wheel -lift type truck
From the frontFrom the rear
Use a towing dolly under the rear
wheels.
Use a towing dolly under the front
wheels.

5848-2. Steps to take in an emergency
RC200t_RC F_EE(OM24728E)
If your vehicle is transported by a flat-
bed truck, it should be tied down at the
locations shown in the illustration.
If you use chains or cables to tie down
your vehicle, the angles shaded in black
must be 45 .
Do not overly tighten the tie downs or
the vehicle may be damaged.
If a tow truck is not available in an emergency, your vehicle may be temporarily
towed using cables or chains secured to the emergency towing eyelets. This
should only be attempted on hard surfac ed roads for at most 80 km (50 miles)
at under 30 km/h (18 mph).
A driver must be in the vehicle to steer and operate the brakes. The vehicle’s
wheels, drive train, axles, steering and brakes must be in good condition.
Using a flatbed truck
Emergency towing

5858-2. Steps to take in an emergency
8
When trouble arises
RC200t_RC F_EE(OM24728E)
Take out the towing eyelet. (P. 620, 635)
Remove the eyelet cover using a flathead screwdriver.
To protect the bodywork, place a rag betw een the screwdriver and the vehicle body as shown in the illustration.
Emergency towing procedure
1
2
RC200t (except F SPORT models)RC200t (F SPORT models)
RC F

5868-2. Steps to take in an emergency
RC200t_RC F_EE(OM24728E)
Insert the towing eyelet into the hole
and tighten partially by hand.
Tighten down the towing eyelet
securely using a wheel nut wrench
or hard metal bar.
Securely attach cables or chains to the towing eyelet.
Take care not to damage the vehicle body.
Enter the vehicle being towed and start the engine.
If the engine does not start, turn the engine switch to IGNITION ON mode.
Shift the shift lever to N and release the parking brake.
When the shift lever cannot be shifted: P. 258
■While towing
If the engine is not running, the power assist for the brakes and steering will not function, making steering and braking more difficult.
■Wheel nut wrench
Wheel nut wrench is installed in trunk. ( P. 620, 635)
3
4
5
6
7