2017 LEXUS LS600H display

1262. Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
Either average fuel consumption
after refueling or driving range can
be selected and displayed.
If displayed on the drive monitor,
other trip information or warning
messages can be displayed simulta-
neously.
For display and selection proce-
dures, follow the “Setting up the dis-
plays”.
The information displayed on the drive
monitor will not be displayed on the
trip information screen.
Drive monitor

1272. Instrument cluster
2
Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
While the vehicle is stopped,
press the “DISP” button until the
“Settings” screen appears.
Press and hold the “DISP” button
until the screen changes.
Press and hold the “DISP” button
after selecting the desired set-
ting item by pressing the “DISP”
button.
Press and hold the “DISP” button
after selecting the desired set-
ting by pressing the “DISP” but-
ton.
The display goes back to step .
Setting up the displays
1
2
3
4
3

1282. Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
Press and hold the “DISP” button
after selecting the “EXIT” by
pressing the “DISP” button.
The display goes back to step .
■System check display
After turning the power switch to ON mode, “SYSTEM CHECK” is displayed while
system operation is checked.
■Tire inflation pressure
●It may take a few minutes to display the tire inflation pressure after the power switch
is turned to ON mode. It may also take a few minutes to display the tire inflation
pressure after inflation pressure has been adjusted.
●“---” may be displayed if the tire position information cannot be determined due to
unfavorable radio wave conditions.
●Tire inflation pressure changes with temperature. The displayed values may also be
different from the values measured using a tire pressure gauge.
■When disconnecting and reconnecting 12-volt battery terminals
The following information data will be reset:
●Driving range
●Average fuel consumption
●Average fuel consumption after refueling
●Distance after refueling
●Elapsed time
●Average vehicle speed
■Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is character-
istic of liquid crystal displays, and there is no problem continuing to use the display.
■Customization
Setting of available languages can be changed. (Customizable features P. 636)
5
1

1292. Instrument cluster
2
Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
CAUTION
■The information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal informa-
tion display. At extremely low temperatures, the information display monitor may
respond slowly, and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear number
appearing on the display. This lag could cause the driver to downshift again, caus-
ing rapid and excessive engine braking and possibly an accident resulting in death
or injury.
■Cautions during setting up the display
As the hybrid system needs to be operating during setting up the display, ensure
that the vehicle is parked in a place with adequate ventilation. In a closed area such
as a garage, exhaust gases including harmful carbon monoxide (CO) may collect
and enter the vehicle. This may lead to death or a serious health hazard.
NOTICE
■During setting up the display
To prevent 12-volt battery discharge, ensure that the hybrid system is operating
while setting up the display features.

1302. Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
Multi-information display
Remote Touch screen
“MENU” button
Remote Touch knob
“ENTER” button
Energy monitor/consumption screen
You can view the status of your hybr id system on the multi-information
display and the Remote Touch screen.
The energy monitor or consumption screen can be displayed and oper-
ated on the side display.
1
2
3
4
5

1312. Instrument cluster
2
Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
■Remote Touch screen (P. 390)
Press the “MENU” button on the Remote Touch, and then select
on the “Menu” screen.
If the “Trip information” or “Past record” screen is displayed, select “Energy”.
■Multi-information display
Press the “DISP” button on the
steering wheel several times to
select the energy monitor display.
Energy monitor

1322. Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
These images are examples only, and may vary slightly from actual conditions.
Remote Touch screenMulti-information display
When the vehicle is pow-
ered by the electric motor
(traction motor)
When the vehicle is pow-
ered by both the gasoline
engine and the electric
motor (traction motor)
When the vehicle is pow-
ered by the gasoline engine
When the vehicle is
charging the hybrid battery
(traction battery)
When there is no energy
flow
Hybrid battery (traction bat-
tery) status
LowFullLowFull

1332. Instrument cluster
2
Instrument cluster
LS600h/LS600hL_EE(OM50G20E)
■Trip information
Press the “MENU” button on the Remote Touch, and then select
on the “Menu” screen.
If the “Energy monitor” or “Past record” screen is displayed, select “Trip infor-
mation”.
Resetting the consumption
data
Fuel consumption in the past
15 minutes
Current fuel consumption
Regenerated energy in the
past 15 minutes
One symbol indicates 30 Wh. Up
to 5 symbols are shown.
Average vehicle speed since
the hybrid system was started.
Elapsed time since the hybrid
system was started.
Cruising range ( P. 135)
Average fuel consumption for the
past 15 minutes is divided by
color into past averages and
averages attained since the
power switch was last turned to
ON mode. Use the displayed
average fuel consumption as a
reference.
The image is an example only, and
may vary slightly from actual condi-
tions.
Fuel Consumption
1
2
3
4
5
6
7