2017 KIA SPORTAGE lights

SPORTAGE FEATURES & FUNCTIONS GUIDE34*IF EQUIPPED
OTHER KEY FEATURES
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will
delete all information).
To program non-rolling and rolling code garage door openers and other devices:
1. Press and hold the left A and center D buttons simultaneously until the
indicator light C begins to flash (to reprogram buttons, skip this step)
2. Press and hold the desired button A, B or D and hold the button on the
transmitter while it is approximately 1 to 3 inches away from the mirror. The
HomeLink® Indicator light C will flash rapidly once the frequency signal has
been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
3. Locate the “learn” or “smart” button on the garage door’s motor head unit.
Press and release the button and complete Step 4 within 30 seconds
4. Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons.
Erasing programmed buttons:
Press and hold the left A and center D buttons simultaneously for
approximately 20 seconds, and then release both buttons within 30 seconds.
REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON.
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to
reduce glare from a vehicle’s headlights located in the rear and also
connect up to three electronic transmitters into one location.
• To turn automatic dimming ON, press button F
• To turn automatic dimming OFF, press button G
HomeLink® with Auto-Dimming
Rearview Mirror*
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON
G Automatic dimming OFF
ABCDEFG

•You can reprogram a single HomeLink® button by repeating Step 2 •Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.

35ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES
Map/Room Lamps
Automatic turn off function*
The interior lights automatically turn off approximately 30 seconds after the
ignition or ENGINE START/STOP button* is OFF.
Map Lamp/Room Lamp Operation
Push the lens A to turn the map lamp ON/OFF. This light produces a spot beam
for convenient use as a map lamp or as a personal lamp for the driver or the
front passenger.
Map/Room Lamp Button - Press button B to turn the front and rear room lamps
on and off.
Door Mode Button - Press button C to enable or disable Door Mode. In Door
Mode, the map and room lamps turn on when any door is opened. When all doors
are locked or the ignition is on, the map and room lamp will turn off immediately.
Rear Room Lamps - Press the button D to turn the rear passenger lamp ON/OFF.

•When doors are unlocked by the Smart Key, the lamp turns ON for approximately 30 seconds •If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage •Using interior lights for an extended period of time may cause battery discharge
QUICK TIPS
A
D
BC
A

37ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES
(Liftgate Release Button)
Located underneath the rear liftgate hatch. With liftgate
unlocked, press the Liftgate Release Button and pull the
liftgate up by the handle to open.
Liftgate Release Button

•The liftgate must be unlocked before it can be opened by the Liftgate Release Button •The liftgate unlocks automatically, and can then be opened, when the Smart Key fob* is within close proximity to the vehicle
QUICK TIPS
Smart Power Liftgate*
When the Smart Key fob is on your person and you are near the
back of the vehicle, within close proximity, the hazard warning
lights will blink and a chime will sound for about 3 seconds as
an alert that the Smart Power Liftgate* is about to open.
Then the alert system will blink and chime two additional times
before opening the Smart Power Liftgate*.
The Smart Power Liftgate* feature is OFF by default. To enable
the Smart Power Liftgate*, go to User Settings in the LCD
Instrument Cluster modes.
During the Smart Power Liftgate alert, the Smart Power
Liftgate can be deactivated with the Smart Key by pressing any
button on the key fob.
REMINDERS:
• All doors are closed and locked after about 15 seconds
• The Smart Power Liftgate feature will not operate when the doors are recently closed and locked, and the Smart Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles, a door is not locked or closed or the Smart Key is in the vehicle
HOLD
For more information on the Smart Power Liftgate operation, please refer to the Owner's Manual.
Smart Power Liftgate Video To view a video on your mobile device, snap this QR Code or visit the listed website.
Refer to page 2 for more information.
www.KuTechVideos.com/ql13/2017
QR CODE