2017 KIA CEED ABS

797
Maintenance
Rear fog light (if equipped)
1. Remove the under cover by rotatingthe screws.
2. Reach your hand into the back of the rear bumper.
3. Disconnect the power connector. 4. Remove the bulb-socket from the
housing by turning the socket counter
clockwise until the tabs on the socketalign with the slots on the housing.
5. Install the new bulb-socket into thehousing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector.
7. Reinstall the rear under cover.
✽✽ NOTICE
Rear fog light is only on the driver’s side
(5 door, if equipped).
OJD073075
OJD075071 OJD073074
JD PE eng 7.QXP 03.01.2017 17:23 Page 97

Maintenance
98
7
Tail light or stop and tail light (LED type)
If the light does not operate, we recom-
mend that the system be checked by an
authorized Kia dealer.
High mounted stop light bulb replacement
If the light does not operate, we recom-
mend that the system be checked by an
authorized Kia dealer.License plate light bulb replace- ment
1. Turn off the engine.
2. Remove the bulb assembly by press-
ing the tabs.
3. Remove the socket by turning it coun- terclockwise.
4. Remove the bulb by pulling it straight out.
5. Install a new bulb.
6. Reinstall the bulb assembly securely with the retaining screws.
OJD072037OGD071046
JD PE eng 7.QXP 03.01.2017 17:24 Page 98

799
Maintenance
Interior light bulb replacement
Map lamp, vanity mirror lamp,room lamp, luggage room lamp
and glove box lamp
1. Using a flat-blade screwdriver, gently pry the lens from the interior light housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior light housing notches and snap the
lens into place.
■Map lamp
■Glove box lamp
■Vanity mirror lamp
■ Luggage room lamp
■Room lamp
OGD071039/OTD079035/OJD072043/OJD072038/OGDE071057/OGD071038---- TTTTyyyyppppeeee AAAA
---- TTTTyyyyppppeeee BBBB
WARNING
Prior to working on the interior
lights, ensure that the light is off to
avoid burning your fingers or
receiving an electric shock.
CAUTION
Be careful not to dirt or damage lens, lens tab, and plastic housings.
JD PE eng 7.QXP 03.01.2017 17:24 Page 99

7105
Maintenance
Interior care
Interior general precautions
Prevent chemicals such as perfume, cos-
metic oil, sun cream, hand cleaner, and
air freshener from contacting the interior
parts because they may cause damage
or discoloration. If they do contact the
interior parts, wipe them off immediately.
See the instructions that follow for the
proper way to clean vinyl.
Taking care of leather seats
Vacuum the seat periodically toremove dust and sand on the seat. It
will prevent abrasion or damage of the
leather and maintain its quality.
Wipe the natural leather seat cover often with dry or soft cloth.
Sufficient use of a leather protective may prevent abrasion of the cover and
helps maintain the color. Be sure to
read the instructions and consult aspecialist when using leather coating
or protective agents.
Leather with bright colors(beige, cream beige) is easily contaminated and clear
in appearance. Clean the seats fre-
quently.
Avoid wiping with wet cloth. It may cause the surface to crack.
Cleaning the leather seats
Remove all contaminations instantly.
Refer to instructions below for removal of each contaminant.
Cosmetic products(sunscreen, founda- tion, etc.)
- Apply cleansing cream on a cloth andwipe the contaminated point. Wipe off
the cream with a wet cloth and
remove water with a dry cloth.
Beverages(coffee, soft drink, etc.) - Apply a small amount of neutraldetergent and wipe until contamina-
tions do not smear.
- Remove oil instantly with absorbablecloth and wipe with stain remover for
natural leather only.
Chewing gum - Harden the gum with ice and removegradually.
CAUTION
Never allow water or other liquids
to come in contact with
electrical/electronic componentsinside the vehicle as this may dam-age them.
CAUTION
When cleaning leather products(steering wheel, seats etc.), use neutral detergents or low alcohol
content solutions. If you use highalcohol content solutions oracid/alkaline detergents, the colorof the leather may fade or the sur-
face may get stripped off.
JD PE eng 7.QXP 03.01.2017 17:24 Page 105

7107
Maintenance
EMISSION CONTROL SYSTEM
The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty infor-
mation contained in the Warranty &
Maintenance book in your vehicle.
Your vehicle is equipped with an emis- sion control system to meet all emission
regulations. There are three emission control sys-
tems which are as follows.
(1) Crankcase emission control system
(2) Evaporative emission control system(3) Exhaust emission control system In order to assure the proper function of
the emission control systems, it is rec-
ommended that you have your car
inspected and maintained by an author-
ized Kia dealer in accordance with the
maintenance schedule. Caution for the Inspection and
Maintenance Test (With Electronic
Stability Control (ESC) system)
To prevent the vehicle from misfir-
ing during dynamometer testing,
turn the Electronic Stability Control
(ESC) system off by pressing the
ESC switch.
After dynamometer testing is com- pleted, turn the ESC system back on
by pressing the ESC switch again.
1. Crankcase emission control system
The positive crankcase ventilation sys-
tem is employed to prevent air pollution
caused by blow-by gases being emitted
from the crankcase. This system supplies
fresh filtered air to the crankcase through
the air intake hose. Inside the crankcase,
the fresh air mixes with blow-by gases,
which then pass through the PCV valveinto the induction system. 2. Evaporative emission control
System
The Evaporative Emission Control
System is designed to prevent fuel
vapors from escaping into the atmos-
phere.
Canister
Fuel vapors generated inside the fuel tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in the
canister are drawn into the surge tank
through the purge control solenoid valve.
Purge Control Solenoid Valve (PCSV)
The purge control solenoid valve is con-
trolled by the Engine Control Module
(ECM); when the engine coolant temper-
ature is low during idling, the PCSV clos-
es so that evaporated fuel is not taken
into the engine. After the engine warms-
up during ordinary driving, the PCSV
opens to introduce evaporated fuel to the
engine.
JD PE eng 7.QXP 03.01.2017 17:24 Page 107

I3
Index
Brake system..................................................................5-40
Anti-lock brake system (ABS)....................................5-48
Electric parking brake (EPB) ......................................5-44
Electronic stability control (ESC) ..............................5-51
Emergency Stop Signal (ESS) ....................................5-56
Good braking practices ..............................................5-56
Hill-start assist control (HAC) ....................................5-55
Parking brake - Hand type ..........................................5-42
Power brakes ..............................................................5-40
Vehicle stability management (VSM) ........................5-54
Brake/clutch fluid ..........................................................7-32 Checking the brake fluid level ....................................7-32
Bulb wattage ....................................................................8-6
Child restraint system ....................................................3-32 Using a child restraint system ....................................3-34
Clean air ......................................................................4-163
Climate control air filter ................................................7-37 Filter inspection ..........................................................7-37
Filter replacement ......................................................7-37
Cruise Control system ..................................................5-58
Declaration of conformity ............................................8-15 Defroster ......................................................................4-139
Rear window defroster ..............................................4-139
Dimensions ......................................................................8-2
Door locks......................................................................4-17 Child-protector rear door lock ....................................4-21
Deadlocks....................................................................4-20
Door lock/unlock features ..........................................4-20
From inside ................................................................4-18
From outside ..............................................................4-17
Dual Clutch Transmission (DCT)..................................5-30 Dual clutch transmission operation ............................5-30
Good driving practices ................................................5-37
Economical operation ....................................................5-81
Emergency commodity ..................................................6-40 Fire extinguisher ........................................................6-40
First aid kit ..................................................................6-40
Tire pressure gauge ....................................................6-40
Triangle reflector ........................................................6-40
Emergency starting ..........................................................6-5 Jump starting ................................................................6-5
Push-starting ................................................................6-7
Emission control system ..............................................7-107
Engine ..............................................................................8-3
Engine compartment ................................................2-6, 7-3
C
D
E