2017 KIA BORREGO lock

Maintenance
64
8
Engine compartment main fuse panel
Fuse NameFuse ratingCircuit Protected
FRT/RR WASHER10AFront/Rear Washer Motor Relay
STOP LAMP20AFAM(STOP SIGNAL 7.5A), DBC Relay, Stop Signal Relay
KEY SW 125AIgnition Switch, PDM Relay Box(IG1 Relay , ACC Relay )
STOP SIGNAL7.5AStop Lamp Switch, Smart Key Control Module
A/C COMP7.5AA/C Comp Relay
FRT DEICER15AFront Deicer Relay
HORN15AHorn Relay
ECU 110A
DIESEL - Immobilizer Module, A/C Comp Relay, Stop Lamp Switch,
E/R Sub Block (Glow Relay, PTC 1~3 Relay), Lambda Sensor
GASOLINE - ECM, Mass Air Flow Sensor, Immobilizer Module, A/C Comp Relay
O2 DN10AGASOLINE - Oxygen Sensor #3/ #4
ECU 215A
DIESEL - EGR Cooling Valve, Electric VGT Actuator /
GASOLINE - Oil Control Valve, ECM, Variable Intake Manifold Valve, Purge Control Solenoid Valve
O2 UP10ADIESEL - Rail Pressure Regulator Valve, Fuel Meter Unit /
GASOLINE : Oxygen Sensor #1/ #2
IGN COIL20AGASOLINE - Ignition Coil #1~#6, Condenser #1,#2
INJECTOR15AECM, Injector #1~#6(GASOLINE)
P/TRAIN7.5AECM, Main Relay
FUEL PUMP15AFuel Pump Relay

865
Maintenance
Fuse NameFuse ratingCircuit Protected
AT M15ATCM
A/SUSP15AAir Suspension Control Module
H/LP WASHER20AHead Lamp Washer Motor & Washer Level Sensor
B/A HORN10ARelay Block (B/A Horn Relay)
ABS 240AABS Control Module, ESC Control Module, Multipurpose Check Connector
ABS 140AABS Control Module, ESC Control Module
PDM20ASmart Key Control Module
FRT WIPER30AFront Wiper ON Relay
KEY SW 230AStart 1 Relay, Ignition Switch, PDM Relay Box(IG2 Relay)
RAM 150ARAM(CONSOL P/OUT 15A, RR P/OUT 15A, FUEL DR 15A, RR P/WIN-LH 20A,
RR P/WIN-RH 20A, LUGGAGE 7.5A)
RAM 250ARAM (RR DEFOG 25A, T/G POWER LATCH 30A, DOOR LOCK 15A,
RR WIPER 15A, MODULE 1 7.5A)
RAM 350ARAM(AMP 30A)
IPM 150AIPM (ILLUMI 7.5A, DDM 30A, SEAT WARMER 20A, OBD-II 7.5A, SUNROOF 25A,
K/LOCK 7.5A, TPMS 7.5A)
IPM 250AIPM (ADM 30A, S/TILT 20A)
IPM 350AIPM (MEMORY 7.5A, DRIVER P/SEAT 30A, PASS P/SEAT 20A, RR S/WARM 20A,
ROOM 7.5A, AUDIO 15A)
4WD30A4WD ECM

867
Maintenance
Engine compartment sub fuse panel
Fuse NameFuse ratingCircuit Protected
COOLING FAN 230ACOOLING FAN 2 RELAY
FUEL HEATER30AFUEL HEATER RELAY
A/SUS40AAIR SUPENSION RELAY
BLOWER FRT40ARELAY BLOCK(FRONT BLOWER RELAY)
BLOWER RR30ARELAY BLOCK(REAR BLOWER RELAY)
PTC HEATER 150APTC 1 RELAY
PTC HEATER 250APTC 2 RELAY
PTC HEATER 350APTC 3 RELAY
COOLING FAN 150ACOOLING FAN 1 RELAY
GLOW80AGLOW RELAY

Maintenance
68
8
LIGHT BULBS
Please prepare bulbs with appropri- ate standards in case of emergen-
cies. (Refer to chapter 9 for further
information)
When changing bulbs and sorts, first
turn off the engine at a safe place,
firmly apply the side brake and take
out the battery's negative (-) terminal.
Use only the bulbs of the specified wattage.
WARNING - Working on the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switchis turned to the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle and burning your fingers or
receiving an electric shock.
WARNING
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause extensive wiring
damage and possible fire.
CAUTION
If you don’t have necessary tools, the correct bulbs and theexpertise, consult an authorized Kia dealer. In many cases, it isdifficult to replace vehicle lightbulbs because other parts of the vehicle must be removed beforeyou can get to the bulb. This isespecially true if you have toremove the headlight assembly to get to the bulb(s). Removing/installing the headlight assem-bly can result in damage to the vehicle.
CAUTION
If unauthentic parts or sub- standard lights are used whenchanging lights, it may lead to fuse disconnection and mal-function, and other wiringdamages.
Do not install extra lamps or LED to the vehicle. If supple-mentary lights are installed, itmay lead to lamp malfunctionand flickering of the lights. In addition, the fuse box andother writing may be damaged.

871
Maintenance
1. Open the hood.
2. Remove the headlight bulb coverby turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector.
4. Unsnap the headlight bulb retain- ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb. 7. Connect the headlight bulb socket-
connector.
8. Install the headlight bulb cover by turning it clockwise.
✽✽ NOTICE
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, we recom-
mend that you consult an authorized
Kia dealer.
Headlight (HID type), position, turn signal, and front fog light bulb replacement
If the light bulb does not operate, we
recommend that you have the vehi-
cle checked by an authorized Kia
dealer.
OEN076051
WARNING
- HID Headlight low beam (if equipped)
Do not attempt to replace or
inspect the low beam (XENON
bulb) due to electric shock dan-
ger. If the low beam (XENON
bulb) is not working, we recom-
mend that you have your vehi-
cle checked by an authorized
Kia dealer.

873
Maintenance
Outside light
Type A
1. Open the tailgate.
2. Loosen the light assembly retain-ing screws with a philips head
screwdriver. 3. Remove the rear combination light
assembly from the body of the
vehicle.
4. Remove the socket from theassembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
OHM078044N
OHM078045N
OHM078046N
OHM078047N

Maintenance
74
8
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
7. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
8. Reinstall the light assembly to the body of the vehicle.
Type B
If the light bulb does not operate, we
recommend that you have the vehi-
cle checked by an authorized Kia
dealer.Inside light
1. Open the tailgate.
2. Remove the service cover using a flat-blade screwdriver.
3. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket. 5. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
7. Install the service cover by putting it into the service hole.
OHM078048
OHM078049

Specifications & Consumer information
10
9
The tires supplied on your new vehi-
cle are chosen to provide the best
performance for normal driving.
The tire label located on the driver's
side center pillar gives the tire pres-
sures recommended for your vehicle.
The engine number is stamped on
the engine block as shown in the
drawing.A compressor label informs you the
type of compressor your vehicle isequipped with such as model, suppli-
er part number, production number,
refrigerant (1) and refrigerant oil (2).
OHM088005N
TIRE SPECIFICATION AND PRESSURE LABEL
ENGINE NUMBER
OHM088006N
OHM088003
■
Gasoline engine (3.8L)
■ Diesel engine (3.0L)
AIR CONDITIONER COMPRESSOR LABEL
ODW081001