2017 JEEP WRANGLER light

Cargo Lamp
The courtesy and dome lights will turn on when the front
doors are opened, by rotating the control for the dimmer
switch on the multifunction lever fully upward, or if
equipped, when the unlock button is pushed on the
Remote Keyless Entry key fob.
The sports bar reading lights (available on four-door
models) can be turned on by pushing the switches, located
on either side of the lens. Push a switch a second time to
turn the light off.The rear cargo light may be turned on by pushing the lens.
Push the lens a second time to turn the light off.
When a door is open and the interior lights are on, rotating
the dimmer control to the extreme bottom position will
cause all the interior lights to turn off. This is also known
as the “Party” mode because it allows the doors to stay
open for extended periods of time without discharging the
vehicle’s battery.
Sports Bar Reading Light
Rear Cargo Light
56 GETTING TO KNOW YOUR VEHICLE

IconDescription
Panel Mode
Bi-Level Mode
Floor Mode
Mix Mode
• Panel Mode
Air comes from the outlets in the instrument panel. Each of these outlets can be individually
adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can
be moved up and down or side to side to regulate airflow direction. There is a shut off
wheel located below the air vanes to shut off or adjust the amount of airflow from these
outlets.
• Bi-Level Mode
Air comes from the instrument panel outlets and floor outlets. A slight amount of air is
directed through the defrost and side window demister outlets.
NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the
panel outlets and warmer air from the floor outlets.
• Floor Mode
Air comes from the floor outlets. A slight amount of air is directed through the defrost and
side window demister outlets.
• Mix Mode
Air is directed through the floor, defrost, and side window demister outlets. This setting
works best in cold or snowy conditions that require extra heat to the windshield. This
setting is good for maintaining comfort while reducing moisture on the windshield. 3
GETTING TO KNOW YOUR VEHICLE 63

IconDescription
Modes Control
Turn the knob to adjust airflow distribution. The airflow distribution mode can be adjusted so
air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.
The Mode settings are as follows:
Panel Mode
Bi-Level Mode
Floor Mode
Mix Mode
• Panel Mode
Air comes from the outlets in the instrument panel. Each of these outlets can be individually
adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can
be moved up and down or side to side to regulate airflow direction. There is a shut off
wheel located below the air vanes to shut off or adjust the amount of airflow from these
outlets.
• Bi-Level Mode
Air comes from the instrument panel outlets and floor outlets. A slight amount of air is
directed through the defrost and side window demister outlets.
NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the
panel outlets and warmer air from the floor outlets.
• Floor Mode
Air comes from the floor outlets. A slight amount of air is directed through the defrost and
side window demister outlets.
• Mix Mode
Air is directed through the floor, defrost, and side window demister outlets. This setting
works best in cold or snowy conditions that require extra heat to the windshield. This
setting is good for maintaining comfort while reducing moisture on the windshield. 3
GETTING TO KNOW YOUR VEHICLE 67

18. Before lowering the top, open the swing gate to preventpossible damage to the rear center high-mounted brake
light. Move to the front of the vehicle. Grasp the side
bow behind the header and lift the top, folding it
toward the rear of the vehicle.
NOTE: Help from another person will ease this operation. 19. Tuck the fabric and the check straps between the bows
and as far inward as possible. This will keep any
portion of the top from flapping outside of the vehicle.
20. Close the front header latches.
21. Remove the door frames, if desired. Refer to “Door Frame” in this section for further information.
Step Eighteen
Step Nineteen
3
GETTING TO KNOW YOUR VEHICLE 119

18. Release the side bows by pushing down on the latchabove the front of the rear door. Push the top rearward
to disengage. Repeat this step on the other side. 19. Before lowering the top, open the swing gate to prevent
possible damage to the rear center high-mounted brake
light. Grasp the folded side bows and slide the top
along the door frame track to the rear door frame.
Step Eighteen
Step Nineteen
152 GETTING TO KNOW YOUR VEHICLE

7. Install the lower windshield plates with the six blackround-headed Torx head screws (using a #40 Torx head
driver) on each side of the base of the windshield.
8. Reinstall the wiper arms.HOOD
Opening The Hood
Release both the hood latches.
Raise the hood and locate the safety latch, located in the
middle of the hood opening. Push the safety latch to the
left side of the vehicle, to open the hood. You may have to
push down slightly on the hood before pushing the safety
latch. Insert the support rod into the slot on the hood.
Step Seven
Hood Latch
3
GETTING TO KNOW YOUR VEHICLE 171

Electrical Power Outlets
There are two 12 Volt (13 Amp) auxiliary power outlets that
can provide power for accessories designed for use with
the standard power outlet adapters.
The front power outlet is located in the center of the
instrument panel below the climate controls, and is pow-
ered from the ignition switch. Power is available when the
ignition switch is in the ON or ACC position.When the optional cigar lighter heating element is used in
the power outlet, it heats when pushed in and pops out
automatically when ready for use.
To preserve the heating
element, do not hold the lighter in the heating position.
A second power outlet is located inside the center console
and is powered directly from the vehicle battery.
CAUTION!
• Do not exceed the maximum power of 160 Watts (13
Amps) at 12 Volts. If the 160 Watt (13 Amp) power
rating is exceeded the fuse protecting the system will
need to be replaced.
•
Power outlets are designed for accessory plugs only.
Do not insert any other object in the power outlets as
this will damage the outlet and blow the fuse. Im-
proper use of the power outlet can cause damage not
covered by your New Vehicle Limited Warranty.
Front Power Outlet
176 GETTING TO KNOW YOUR VEHICLE

On vehicles equipped with a rear subwoofer, there is a
third power outlet located in the right rear cargo area.
Rear Power Outlet — If Equipped
Power Outlet Fuse Locations
1 — M36 Fuse 20 A Yellow Power Outlet Console Bin
2 — M6 Fuse 20 A Yellow Cigar Lighter Instrument Panel
3 — M7 Fuse 20 A Yellow Power Outlet Rear with Sub Woofer
(Opt.)
3
GETTING TO KNOW YOUR VEHICLE 177