2017 JEEP GRAND CHEROKEE wheel

NOTE:The Uconnect Owner’s website will store up to ten timer runs.
After ten have been saved, the system will begin to replacer the oldest
entries with any newly performed entries.
• Press the “Cancel” button to view the previously displayed timer “Ticket.”
The “Tickets” contain the timers listed below:
Reaction Time
• The reaction timer measures the time from a visual cue in the cluster to when the vehicle's speed is measured to be greater than zero.
⅛ Mile (200 meter)
• Displays the time it takes for the vehicle to go an ⅛Mile
(200 meters).
¼ mile (400 meter)
• Displays the time it takes for the vehicle to go an ¼ mile (400 meters).
60 ft time
• Displays the time it takes for the vehicle to go 60 ft. Brake Distance
• Displays the distance it takes the vehicle to make a full stop.
Contains current and last data for distance and start – from speed.
NOTE: The distance measurement will be aborted if the brake pedal is
released before the vehicle comes to a complete stop.
Brake Speed
• Displays the speed the vehicle is traveling when the brake pedal is depressed.
NOTE: Brake Distance and Speed timers will only display "ready" when
vehicle is traveling at greater than 30 MPH (48 km/h).
NOTE:
• Brake Distance and Speed timers will only display "ready" when vehicle is traveling at greater than 30 MPH (48 km/h).
• To clear the timer values, use the steering wheel controls while on the specific timer page in the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL
9

G-Force
When selected, this screen displays all four G-Force values (two lateral
and two longitudinal) as well as steering angle.When G-Force is selected, the following features will be available:
Lateral G-Force Left and Right
• The lateral g-force measures the (sideways) left and right force of the
vehicle.
Longitudinal G-Force Acceleration and Braking
• The longitudinal g-force measures the acceleration and braking force of the vehicle.
Peak G-Forces Acceleration and Braking, Left and Right
• This shows the maximum g-forces that have been achieved since the last reset from the instrument cluster display. Peak values are
maintained through ignition cycles by the instrument cluster display
until they are cleared by the driver.
NOTE: To clear peak values, use the steering wheel controls while on the
instrument cluster g-force page.
Vehicle Speed
• Vehicle Speed measures the current speed of the vehicle in either mph or km/h, starting at zero with no maximum value.
Steering Wheel Angle
•
Steering Wheel Angle utilizes the steering angle sensor to measure the
degree of the steering wheel relative to zero. The zero degree measure-
ment indicates a steering wheel straight ahead position. When the
steering angle value is negative, this indicates a turn to the left, and
when the steering angle value is positive, a turn to the right.
SRT Performance Pages — G-Force
UNDERSTANDING YOUR INSTRUMENT PANEL
12

Listed below are the available Drive Modes:
Track Mode
Selecting “Track” with the Selec-Track switch will activate the configu-
ration for typical track driving. The Transmission, Stability Control,
All-Wheel Drive, Steering, and Suspension systems are all set to their
“Track” settings highlighted in red. The Paddle Shifters are enabled.Sport Mode
Selecting “Sport” with the Selec-Track switch will activate the configu-
ration for typical enthusiast driving. The Transmission, Stability Con-
trol, All-Wheel Drive, Steering, and Suspension systems are all set to
their “Sport” settings highlighted in orange. The Paddle Shifters are
enabled.
Drive Modes — Track
Drive Modes (Sport)
UNDERSTANDING YOUR INSTRUMENT PANEL
15

Tow ModeSelecting “Tow” with the Selec-Track switch will activate the configu-
ration for towing a trailer or hauling heavy loads in the cargo area. Once
in this mode, trailer sway control is enabled in the ESC system. The
Transmission is set to “Tow” setting highlighted in purple. Stability
Control is set to “Full” highlighted in blue. All-Wheel Drive is set to
“50/50” highlighted in blue. Steering is set to “Street” highlighted in
yellow. Suspension is set to “Sport” highlighted in orange.
Drive Modes - Tow
UNDERSTANDING YOUR INSTRUMENT PANEL
16

Snow Mode
Selecting “Snow” with the Selec-Track switch will activate snow mode
for use on loose traction surfaces. When in Snow mode (depending on
certain operating conditions), the transmission will use second gear
(rather than first gear) during launches, to minimize wheel slippage.
The Transmission is set to “Snow” setting highlighted in blue. StabilityControl is set to “Full” highlighted in blue. All-Wheel Drive is set to
“50/50” highlighted in blue. Steering is set to “Street” highlighted in
yellow. Suspension is set to “Street” highlighted in yellow.
Paddle shifters can be enabled or disabled by pressing the “Snow
Set-up” button on the touchscreen.
Drive Mode Snow
Snow Mode Set-Up
UNDERSTANDING YOUR INSTRUMENT PANEL
17

Auto Mode
Auto mode is enabled upon ignition on, or by selecting “Auto” with the
Selec-Track switch. The Transmission, Stability Control and All-Wheel
Drive modes are set to their “Street” settings highlighted in yellow.
Steering and Suspension can be configured in either the “Street,”
“Sport,” or “Track” and the Paddle Shifters may be enabled or disabled
while in auto set-up mode.
Drive Mode Auto (Default)
Auto Mode Setup (Default)
UNDERSTANDING YOUR INSTRUMENT PANEL
18

Custom Mode
Custom Mode may be selected by pushing the “Custom” button on
Selec-Track switch. Custom Mode allows you to create a custom
configuration that is saved for quick selection of your favorite settings.
While in Custom Mode, the All-Wheel Drive, Stability Control, Trans-
mission, Steering, Suspension, and Paddle Shifter settings are shown
in their current configuration.While in the Custom Mode screen, press the “Custom Set-Up” button
on the touchscreen to access the selectable options. Select which
mode suits your driving needs for a custom driving experience.
Custom Mode Set-Up Info
Within the Custom Mode Set-Up screen, press the “info” button on the
touchscreen then use the left/right arrows to scroll through all the
available Drive Mode systems giving you a description of their operation
and current configuration.
Custom Mode
Custom Mode Set-Up
UNDERSTANDING YOUR INSTRUMENT PANEL
19

All-Wheel DriveTrack
• Press the “Track” button on the touchscreen to provide the greatest
distribution of torque to the rear wheels (70%.)
Sport
• Press the “Sport” button on the touchscreen to provide greater distribution of torque to the rear wheels (65%.)
Street
• Press the “Street” button on the touchscreen to provide moderate distribution of torque to the rear wheels (60%.)
50/50
• Press the “50/50” button on the touchscreen to provide even distribution of torque between the front and rear wheels.
All-Wheel Drive
UNDERSTANDING YOUR INSTRUMENT PANEL
20