2017 INFINITI QX30 lock

WARNING
•The seatback should not be reclined any
more than needed for comfort. Seat belts
are most effective when the passenger sits
well back and straight up in the seat. If the
seat back is reclined, the risk of sliding un-
der the lap belt and being injured is in-
creased.
•For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back and upright in the
seat with both feet on the floor and adjust
the seat properly. (SeeSeat beltslater in
this section.)
•After adjustment, gently rock in the seat to
make sure it is securely locked.
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle. Addition-
ally, the temperature inside a closed vehicle
on a warm day can quickly become high
enough to cause a significant risk of injury
or death to people and pets.
•Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls. Unattended children
could become involved in serious accidents.
•Do not adjust the driver’s seat while driving
so full attention may be given to vehicle
operation. The seat may move suddenly and
could cause loss of control of the vehicle.
CAUTION
When adjusting the seat positions, be sure not
to contact any moving parts to avoid possible
injuries and/or damage.
SSS0133AZ
SEATS
1-2Safety — seats, seat belts and supplemental restraint system

FRONT SEATS
Manual seat adjustment
Forward and backward:
Pull the lever1up and hold it while sliding the
seat forward or backward to the preferred posi-
tion. Release the lever to lock the seat in
position.
Seat cushion angle (if equipped)
:
Adjust the angles so that your thighs are lightly
supported. Turn handwheel
2forwards or
backwards.Seat lifter (if equipped)
:
Repeatedly pull up or push down the adjusting
lever
3, to adjust the seat height to the
desired position.
Seatback angle
:
Relieve the pressure on the seatback and turn
handwheel
4forwards or backwards.
The reclining feature allows the adjustment of
the seatback for occupants of different sizes to
help obtain the proper seat belt fit. (SeeSeat
beltslater in this section.)
The seatback may be reclined to allow occu-
pants to rest when the vehicle is parked.Lumbar support
:
The lumbar support feature provides lower back
support to the driver.
Push each side of the adjusting switch to adjust
the seat lumbar area until the desired position
is achieved.
1To raise the seatback contour
2To soften the seatback contour
3To lower the seatback contour
4To harden the seatback contour
NIC2605NIC2607
Safety — seats, seat belts and supplemental restraint system1-3

Folding
The luggage compartment loading capacity can
be increased by folding the rear seat backs
forward.
To fold the seat back
:
1. Ensure head restraints are properly stowed,
seeHead restraints/Headrestslater in this
section.
2. Release the seat back lock by pulling the
release handle.
3. Fold the seat back forward .4. Insert the seat belt into the seat belt holder.
To return the seat back to an upright position
:
1. Make sure the seat belts are clear of the
seat back latch mechanism.
2. Lift the seat back up and push firmly to lock.
3. If the red marker is visible then the seat
back has not latched properly — release and
then re-latch the seat.
4. If the head restraint/headrest was removed,
reinstall and properly adjust the head
restraint/headrest before an occupant uses
the seating position. SeeHead
restraints/Headrestslater in this section.
WARNING
Always use the seat belt holder, and ensure
that the seat belt is not trapped in the seat
back latch mechanism. Failure to do so may
cause damage to the seat belt, and this may
increase the risk of serious injury or death in a
collision.
NPA1293NIC2669
1-6Safety — seats, seat belts and supplemental restraint system

ARMREST (IF EQUIPPED)
Rear
Pull the tab and draw the armrest1forward
until it is horizontal.
Indicates that the seating position is
equipped with a head restraint.
Indicates that the seating position is
equipped with a non-removable head rest.
WARNING
Head restraints/headrests supplement the
other vehicle safety systems. They may pro-
vide additional protection against injury in cer-
tain rear end collisions. Adjustable head
restraints/headrests must be adjusted prop-
erly, as specified in this section. Check the
adjustment after someone else uses the seat.
Do not attach anything to the head restraint/
headrest stalks or remove the head restraint/
headrest. Do not use the seat if the head
restraint/headrest has been removed. If the
head restraint/headrest was removed, rein-stall and properly adjust the head restraint/
headrest before an occupant uses the seating
position. Failure to follow these instructions
can reduce the effectiveness of the head
restraints/headrests. This may increase the
risk of serious injury or death in a collision.
•Your vehicle is equipped with head
restraints/headrests that may be integrated,
adjustable or non-adjustable.
•Adjustable head restraints/headrests have
multiple notches along the stalk to lock them
in a desired adjustment position.
•The non-adjustable head restraints/
headrests have a single locking notch to
secure them to the seat frame.
•Proper Adjustment:
– For the adjustable type, align the head
restraint/headrest so the center of your
ear is approximately level with the center
of the head restraint/headrest.
– If your ear position is still higher than the
recommended alignment, place the head
restraint/headrest at the highest posi-
tion.
NIC2611NPA1500
HEAD RESTRAINTS/HEADRESTS
Safety — seats, seat belts and supplemental restraint system1-7

•If the head restraint/headrest has been
removed, ensure that it is reinstalled and
locked in place before riding in that desig-
nated seating position.
NOTE
For vehicles with sports seats you cannot adjust
the front head restraints/headrests or the outer
rear head restraints/headrests.
ADJUSTABLE HEAD RESTRAINT
COMPONENTS
1. Removable head restraint/headrest
2. Multiple notches
3. Lock knob
4. Stalks
REMOVE
Use the following procedure to remove the head
restraint/headrest.
1. Pull the head restraint/headrest up to the
highest position.
2. Push and hold the lock knob.
3. Remove the head restraint/headrest from
the seat.
4. Store the head restraint/headrest properly
in a secure place so it is not loose in the
vehicle.
5. Reinstall and properly adjust the head
restraint/headrest before an occupant uses
the seating position.
SSS0992ZSSS1037Z
1-8Safety — seats, seat belts and supplemental restraint system

INSTALL
1. Align the head restraint/headrest stalks
with the holes in the seat. Make sure that the
head restraint/headrest is facing the correct
direction. The stalk with the adjustment
notch
1must be installed in the hole with
the lock knob
2.
2. Push and hold the lock knob and push the
head restraint/headrest down.
3. Properly adjust the head restraint/headrest
before an occupant uses the seating posi-
tion.
ADJUST
For adjustable head restraint/ headrest
Adjust the head restraint/headrest so the cen-
ter is level with the center of your ears. If your
ear position is still higher than the recom-
mended alignment, place the head restraint/
headrest at the highest position.
Raise
To raise the head restraint/headrest, pull it up.
Make sure the head restraint/headrest is posi-
tioned from the stored position or any non-latch
position so the lock knob is engaged in the
notch before riding in that designated seating
position.
SSS1038ZSSS0997ZSSS1035Z
Safety — seats, seat belts and supplemental restraint system1-9

Lower
To lower, push and hold the lock knob1and
push the head restraint/headrest down.
Make sure the head restraint/headrest is posi-
tioned so the lock knob is engaged in the notch
before riding in that designated seating posi-
tion.
Fore-aft
This function allows you to adjust the distance
between the head restraint/headrest and the
back of the head.
•To move forwards: pull the head restraint/
headrest forwards in the direction of the
arrow until it engages. There are a number of
detents.
•To move backwards: press and hold button
1and push the head restraint/headrest
backwards.
•When the head restraint/headrest is in the
desired position, release the button and
make sure that the head restraint/headrest
is engaged in position.
REAR SEAT HEAD RESTRAINTS/
HEADRESTS
Adjusting the rear seat head
restraint/headrest height
Use the head restraint/headrest in the notched
stem positions after pulling it up from the
stowed position to a position in which it locks
securely in place.
•To raise: pull the head restraint/headrest up
to the desired height.
•To lower: press release catch1and push
the head restraint/headrest down until it is
in the desired position.
SSS1036ZNIC2610NIC2609
1-10Safety — seats, seat belts and supplemental restraint system

SEAT BELT WARNING LIGHT
The seat belt warning light reminds you to
fasten your seat belts. The light illuminates if
the engine is started, all doors are closed and
the driver’s and/or front passenger’s seat belt
is unfastened. It will remain illuminated until
the driver and/or front passenger fastens their
seat belt. A chime will sound once the vehicle is
in motion.
If the seat belt warning light flashes, together
with an intermittent warning tone, this means
that the driver or passenger has not fastened
their seat belt, and the speed of the vehicle is
exceeding 15 MPH (25 km/h).
For additional information, refer toWarning
lights, indicator lights and audible reminders
in the2. Instruments and controlssection.
THREE-POINT TYPE SEAT BELT WITH
RETRACTOR
WARNING
•Every person who drives or rides in this
vehicle should use a seat belt at all times.
Children should be in the rear seats and in
an appropriate restraint.
•Do not ride in a moving vehicle when the
seatback is reclined. This can be dangerous.
The shoulder belt will not be against your
body. In an accident, you could be thrown
into it and receive neck or other serious in-
juries. You could also slide under the lap
belt and receive serious internal injuries.
•For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back and upright in the
seat with both feet on the floor and adjust
the seat belt properly.
•Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the ALR
mode activated, the child can be seriously
injured or killed if the seat belt retracts and
becomes tight. This can occur even if thevehicle is parked. Unbuckle the seat belt to
release the child. If the seat belt cannot be
unbuckled or is already unbuckled, release
the child by cutting the seat belt with a
suitable tool (such as a knife or scissors) to
release the seat belt.
Fastening the seat belts
1. Adjust the seat. (SeeSeatsearlier in this
section.)
2. Slowly pull the seat belt out of the retractor
and insert the tongue into the buckle until
you hear and feel the latch engage.NIC2743
1-14Safety — seats, seat belts and supplemental restraint system