2017 INFINITI QX30 ignition

DOOR LOCKS/UNLOCKS PRECAUTION
•Do not touch the door handle request switch
with the Intelligent Key held in your hand as
illustrated. The close distance to the door
handle will cause the Intelligent Key system
to have difficulty recognizing that the Intelli-
gent Key is outside the vehicle.
•To prevent the Intelligent Key from being left
inside the vehicle, make sure you carry the
Intelligent Key
INFINITI INTELLIGENT KEY OPERATION
You can lock or unlock the doors without taking
the Intelligent Key out of your pocket or bag.
When you carry the Intelligent Key with you, you
can lock or unlock all doors by pushing the door
handle request switch within the range of op-
eration.
Locking doors
1. Push the P (Park) button to engage the P
(Park) position, place the ignition switch in
the LOCK position and make sure you carry
the Intelligent Key with you.
2. Close all doors.
3. Touch any sensor surface
1or2.
4. All doors and the lift gate will lock.5. The turn signals flash three times.
NOTE
•Doors do not lock by pushing the door
handle request switch while any door is
open. However, doors lock with the mechani-
cal key even if any door is open.
•The driver’s door and the door at which the
handle is used, must both be closed.
•The doors may not lock when the Intelligent
Key is in the same hand that is operating the
request switch to lock the door. Put the
Intelligent Key in a purse, pocket or your
other hand.
CAUTION
•When locking the doors using the request
switch, make sure to have the Intelligent
Key in your possession before operating the
request switch to prevent the Intelligent
Key from being left in the vehicle.
•The request switch is operational only
when the Intelligent Key has been detected
by the Intelligent Key system.
WPD0375ZNPA1489
3-10Pre-driving checks and adjustments

VANITY MIRROR
To use the front vanity mirror3, pull down the
sun visor
1and pull up the cover4.
AUTOMATIC ANTI-GLARE REAR VIEW
MIRROR
The inside mirror is designed so that it auto-
matically dims according to the intensity of the
headlights of the vehicle following you. The
automatic anti-glare feature operates only when
the ignition switch is in the ON position. It will
not operate if reverse gear is engaged or if the
interior lighting is switched on.
OUTSIDE MIRRORS
The driver’s-side outside mirror is designed so
that it automatically dims according to the inten-
sity of the headlights of the vehicle following you.
The automatic anti-glare feature operates only
when the ignition switch is in the ON position. It
will not operate if reverse gear is engaged or if
the interior lighting is switched on.
Adjusting
The outside rear view mirror remote control will
operate only when the ignition switch is in the
ACC or ON position.
1. Move the switch to select the left
1or right
mirror
2.
2. Adjust each mirror to the desired position
using the large switch
3.
Defogging
The exterior rear view mirrors will be heated
when the rear window defogger switch is oper-
ated.
NIC2676NDI1630NIC2636
MIRRORS
Pre-driving checks and adjustments3-17

WARNING
•Objects viewed in the outside mirror on the
passenger side are closer than they appear.
Be careful when moving to the right. Using
only this mirror could cause an accident.
Use the inside mirror or glance over your
shoulder to properly judge distances to
other objects.
•Do not adjust the mirrors while driving. You
could lose control of your vehicle and cause
an accident.
Folding
Manual type (if equipped):
Fold the outside rear-view mirror by pushing it
towards the rear of the vehicle.
Remote control type (if equipped)
:
The exterior rear view mirror remote control
operates when the ignition switch is in the ACC
or ON position.
Briefly press button
1. Both exterior mirrors
fold in or out.
Power folding outside mirrors (if so
equipped)
CAUTION
•Do not touch the mirrors while they are
moving. Your hand may be pinched, and the
mirror may malfunction.
•Do not drive with the mirrors stored. You
will be unable to see behind the vehicle.
The exterior rear-view mirrors automatically un-
fold when the ignition is switched on or when
the vehicle doors are unlocked. Use the [Fold
Mirrors in when Locking] option under the [CON-
VENIENCE] menu of the Vehicle Information
Display to specify that the mirrors are to beautomatically folded and unfolded. The Auto
fold feature can also be switched off. See
Switching the [Fold Mirrors in when Locking]
function on/offin the2. Instruments and
controlssection.
If the [Fold Mirrors in when Locking] option has
been activated in the Vehicle information dis-
play:
•The exterior mirrors fold in automatically as
soon as you lock the vehicle from the out-
side.
•The exterior mirrors fold out again automati-
cally as soon as you unlock the vehicle and
then open the driver’s or front-passenger
door.
Automatic parking positioner (if so
equipped)
The Parking position for the exterior mirror on
the front-passenger side function is only avail-
able if the vehicle is equipped with the Memory
package.
NIC2638
3-18Pre-driving checks and adjustments

1Button for the exterior mirror on the left
hand side.
2Button for the exterior mirror on the
right hand side.
3Adjustment button.
4Memory button M.
Setting and storing the parking position using
reverse gear
:
You can set the front-passenger side exterior
mirror so that you can see the rear wheel on
that side as soon as you engage reverse gear.
You can store this position.
1. Make sure that the vehicle is stationary.
2. Switch the ignition switch to the ON posi-
tion.
3. Press button
2for the external mirror on
the front-passenger side.4. Engage reverse gear. The exterior mirror on
the front-passenger side moves to the preset
parking position.
5. Use adjustment button
3to adjust the
exterior mirror. You should see the rear
wheel and the curb in the exterior mirror The
parking position is stored.
NOTE
•If you shift the transmission to another
position, the exterior mirror on the front
passenger side returns to the driving posi-
tion.
•If the driver’s side mirror is currently se-
lected, the passenger side mirror will not
move when reverse gear is engaged.
Setting and storing the parking position using
the memory button
:
You can set the front-passenger side exterior
mirror so that you can see the rear wheel on
that side as soon as you engage reverse gear.
This setting can be stored using memory button
M
4.
1. Make sure that the vehicle is stationary.
2. Switch the ignition switch to the ON posi-
tion.3. Press button
2for the external mirror on
the front-passenger side.
4. Engage reverse gear. The exterior mirror on
the front-passenger side moves to the preset
parking position.
5. Use adjustment button
3to adjust the
exterior mirror. You should see the rear
wheel and the curb in the exterior mirror.
6. Press memory button M
4and one of the
arrows on adjustment button
3within
three seconds. The parking position is
stored if the exterior mirror does not move.
7. If the mirror moves out of position, repeat
the steps.
Calling up a stored parking position
:
1. Switch the ignition switch to the ON posi-
tion.
2. Adjust the exterior mirror on the front
passenger side with the corresponding but-
ton.
3. Engage reverse gear. The exterior mirror on
the front-passenger side moves to the stored
parking position
NIC2639
Pre-driving checks and adjustments3-19

The exterior mirror on the front-passenger side
moves back to its original position:
•As soon as you exceed a speed of 15 km/h.
•About ten seconds after you have disen-
gaged reverse gear.
•If you press button1for the exterior mirror
on the driver’s side.
WARNING
•If you use the memory function on the driv-
er’s side while driving, the adjustments
could cause you to lose control of the ve-
hicle. There is a risk of an accident. Only use
the memory function on the driver’s side
while the vehicle is stationary.
Only use the memory function on the driv-
er’s side while the vehicle is stationary.
•If the memory function adjusts the seat, you
and other vehicle occupants-particularly
children-could become trapped. There is a
risk of injury.
While the memory function is making ad-
justments, make sure that no one has any
part of their body within the sweep of the
seat. If someone becomes trapped, immedi-ately release the memory function position
button The adjustment is stopped.
•If children activate the memory function,
they could become trapped, especially if
they are unattended. There is a risk of in-
jury.
When leaving the vehicle, always take the
key with you and lock the vehicle. Never
leave children unattended in the vehicle.
The memory function can be used at any time,
e.g. even when the key isn’t in the ignition lock.
STORING SETTINGS
With the memory function, you can store up to
three different settings.
•Seat and seatback position
•Driver’s side: position of the exterior mirrors
on the driver’s and front-passenger sides.
To store settings:
1. Adjust the seat (seePower seat
adjustmentin the1. Safety — seats, seat
belts and supplemental restraint system
section).
NIC2637
MEMORY FUNCTION (IF EQUIPPED)
3-20Pre-driving checks and adjustments

1USB/iPod connection port:
Connect to play media from an iPod
R,
iPhone
Ror a USB memory device.
When using INFINITI InTouch Apps with
an iPhone
R, connect via a USB cable.
Refer to the device manufacturer’s owner
information regarding the proper use
and care of the device.
CAUTION
•Depending on the size and shape of USB
device, the console lid may not fully close.
Do not force the console lid closed as this
may damage the USB device.NOTE
•Even when iPodsRor iPhonesRare
connected to both of the two USB/iPod
Rconnection ports, the system recognizes only
one of the connected iPods
Ror iPhonesRat a time.
•Only one of the two connected USB devices
can be operated by the voice recognition
system.
STARTING SYSTEM
The system starts when the ignition switch is
placed in the ACC or ON position.
Start-up warning (models with
navigation system)
For this system, when the ignition switch is
placed in the ACC or ON position, the start-up
screen is displayed.
Touch [OK] after reading and agreeing to the
message. If you do not agree to the message,
some of Infiniti InTouch
TMfunctions will be
disabled.NOTE
•Do not keep the INFINITI InTouch system
turned on with the engine stopped. Doing so
may discharge the vehicle battery. When you
use INFINITI InTouch, always keep the engine
running.
•Once you select [Decline] on the start-up
screen, the [OK]/[Decline] screen will not be
displayed for 30 days.
NAA1628
4-4Display screen, heater and air conditioner, and audio system

Language settings
From the Language screen, you can change the display language used by the system.
1. Push

•The RearView Monitor is a convenience fea-
ture but it is not a substitute for proper
backing up. Always turn and look out the
windows, and check mirrors to be sure that
it is safe to move before operating the ve-
hicle. Always back up slowly.
•The system is designed as an aid to the
driver in showing large stationary objects
directly behind the vehicle, to help avoid
damaging the vehicle.
•The distance guide line and the vehicle
width line should be used as a reference
only when the vehicle is on a level paved
surface. The distance viewed on the monitor
is for reference only and may be different
than the actual distance between the ve-
hicle and displayed objects.
CAUTION
Do not scratch the camera lens when cleaning
dirt or snow from the lens.
The RearView Monitor system automatically
shows a rear view of the vehicle when the shift
lever is placed in the R (Reverse) position.
The radio can still be heard while the RearView
Monitor is active.To display the rear view, the RearView Monitor
system uses a camera located just above the
vehicle’s rear license plate
1.
REARVIEW MONITOR SYSTEM
OPERATION
With the ignition switch in the ON position,
move the shift lever to the R (Reverse) position
to operate the RearView Monitor.
HOW TO READ THE DISPLAYED LINES
Guiding lines which indicate the vehicle width
and distances to objects with reference to the
bumper line
Aare displayed on the monitor.
Distance guide lines:
Indicate distances from the bumper.
•Red line1: approx. 1.5 ft (0.5 m)
•Yellow line2: approx. 3 ft (1 m)
•Green line3: approx. 7 ft (2 m)
•Green line4: approx. 10 ft (3 m)
Vehicle width guide lines
5:
Indicate the approximate vehicle width when
backing up.
NAA1642SAA1896Z
4-18Display screen, heater and air conditioner, and audio system