2017 INFINITI QX30 sensor

Illustration 2: If the driver activates the turn
signal, then the system chimes (twice) and the
BSW indicator light flashes.
NOTE
•The radar sensors may not detect vehicles
which are approaching rapidly from behind.
•If the driver activates the turn signal before
a vehicle enters the detection zone, the BSW
indicator light will flash but no chime will
sound when the other vehicle is detected.
Accelerate from a stop
NOTE
Illustration 3: If you accelerate from a stop with a
vehicle in the detection zone, the other vehicle
may not be detected.
Overtaking another vehicle
When you overtake a vehicle, the warning only
occurs if the difference in speed is less than 7
MPH (12 km/h).
Illustration 4: The side indicator light illumi-
nates if you overtake a vehicle and that vehicle
stays in the detection zone for approximately 3
seconds.
SSD1031ZIllustration 2 – Approaching from behindSSD1032ZIllustration3–Accelerate from a stopSSD1033ZIllustration4–Overtaking another vehicle
5-40Starting and driving

Illustration 5: If the driver activates the turn
signal while another vehicle is in the detection
zone, then the system chimes (twice) and the
BSW indicator light flashes.
NOTE
•When overtaking several vehicles in a row,
the vehicles after the first vehicle may not be
detected if they are travelling close together.
•The radar sensors may not detect slower
moving vehicles if they are passed quickly.
•If the driver activates the turn signal before
a vehicle enters the detection zone, the side
indicator light will flash but no chime will
sound when the other vehicle is detected.
Overtaking several vehicles
Illustration 6: When overtaking several vehicles
in a row, the vehicles after the first vehicle may
not be detected if they are travelling close
together.
SSD1034ZIllustration5–Overtaking another vehicleSSD1036ZIllustration6–Overtaking several vehicles
Starting and driving5-41

Entering from the side
Illustration 7: The side indicator light illumi-
nates if a vehicle enters the detection zone from
either side.Illustration 8: If the driver activates the turn
signal, then the BSW indicator light flashes and
a chime will sound twice.
NOTE
•The radar sensors may not detect a vehicle
which is travelling at about the same speed
as your vehicle when it enters the detection
zone.
•If the driver activates the turn signal before
a vehicle enters the detection zone, the BSW
indicator light will flash but no chime will
sound when another vehicle is detected.
SSD1037ZIllustration 7 – Entering from the sideSSD1038ZIllustration8–Entering from the side
5-42Starting and driving

SYSTEM TEMPORARILY UNAVAILABLE
1Vehicle information display
If radar blockage is detected, the system will be
turned off automatically, and the [Blind Spot
Warning Currently Unavailable See Operator’sManual] message appears in the vehicle infor-
mation display1. The system is not available
until the conditions no longer exist.
The radar sensors may be blocked by temporary
ambient conditions such as splashing water,
mist or fog. The blocked condition may also becaused by objects such as ice, frost or dirt
obstructing the radar sensors.
Action to take:When the above conditions no
longer exist, the system will resume automati-
cally. If the message still appears, have the
system checked. It is recommended you visit an
INFINITI retailer for this service.
System malfunction
If the system malfunctions, it will be turned off
automatically, and the [Blind Spot Warning
Inoperative] message appears in the vehicle
information display
1.
Action to take:Stop the vehicle in a safe loca-
tion, place the vehicle in the P (Park) position,
turn the engine off and restart the engine.
If the message still appears, have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
NSD631
Starting and driving5-43

RADAR MAINTENANCE
The two radar sensor unitsAfor the BSW
system are located near the rear bumper. Al-
ways keep the area near the radar sensors
clean.
The radar sensors may be blocked by temporary
ambient conditions such as splashing water,
mist or fog.
The blocked condition may also be caused by
objects such as ice, frost or dirt obstructing the
radar sensors.
Check for and remove objects obstructing the
area around the radar sensors.
Do not attach stickers (including transparent
material), install accessories or apply addi-
tional paint near the radar sensors.Do not strike or damage the area around the
radar sensors. It is recommended you consult
an INFINITI retailer if the area around the radar
sensors is damaged due to a collision.
FCC NOTICE
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modification not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equip-
ment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause
undesired operation of the device.Cruise control maintains a constant road speed
for you. It brakes automatically in order to avoid
exceeding the set speed. You must select a
lower gear in good time on long and steep
downhill gradients, especially if the vehicle is
laden or towing a trailer.WARNING
For vehicles with automatic transmission, you
need to have selected manual drive program M
(seeManual drive programearlier in this sec-
tion). By doing so, you will make use of the
braking effect of the engine. This relieves the
load on the brake system and prevents the
brakes from overheating and wearing too
quickly.
Use cruise control only if road and traffic con-
ditions are appropriate for maintaining a steady
speed for a prolonged period. You can set the
cruise control at any road speed above 20 MPH
(30 km/h).
The speed indicated in the speedometer may
differ slightly from the set speed.
NAA1640
CRUISE CONTROL
5-44Starting and driving

ICC SYSTEM OPERATION
1Speedometer
2Distance warning light
3Vehicle information display
4Cruise control leverThe ICC system is intended to enhance the
operation of the vehicle when following a ve-
hicle traveling in the same lane and direction.
If the distance sensorAdetects a slower
moving vehicle ahead, the system will reducethe vehicle speed so that your vehicle follows
the vehicle in front at the selected distance.
The ICC system maintains a selected distance
from the vehicle in front of you within the speed
range of 0 to 125 MPH (0 to 200 km/h) up to the
set speed. The set speed can be selected by the
driver between 20 to 125 MPH (30 to 200 km/h).
The vehicle travels at a set speed when the road
ahead is clear.
The ICC system is designed to maintain a
selected distance from the vehicle in front of
you and reduce the speed to match a slower
vehicle ahead. The system will decelerate the
vehicle as necessary and if the vehicle ahead
comes to a stop, the vehicle decelerates to a
standstill. However, the ICC system can only
apply up to 50% of the vehicle’s total braking
power. This system should only be used when
traffic conditions allow vehicle speeds to re-
main fairly constant or when vehicle speeds
change gradually. If a vehicle moves into the
traveling lane ahead or if a vehicle traveling
ahead rapidly decelerates, the distance be-
tween vehicles may become closer because the
ICC system cannot decelerate the vehicle
quickly enough. If this occurs, the ICC system
will sound a warning chime and illuminate the
distance warning light to notify the driver to
take necessary action.
NSD625
5-48Starting and driving

•The warning chime will not sound and the
distance warning light will not illuminate
when:
– The vehicle approaches other vehicles
that are parked or moving slowly.
– The accelerator pedal is depressed, over-
riding the system.
Also, the sensor sensitivity can be affected by
vehicle operation (steering maneuver or driving
position in the lane) or traffic or vehicle condi-
tion (for example, if a vehicle is being driven
with some damage).
Automatic cancellation
A chime sounds and the message [ICC off] is
displayed in the vehicle information display for
5 seconds under the following conditions and
the control is automatically canceled.
•The electric parking brake is applied.
•The VDC intervenes or the VDC is deactivated.
•The P (Park), R (Reverse) or N (Neutral)
position is engaged.
•The cruise control lever is pulled in order to
pull away but the front passenger door or
one of the rear doors is open.
•The vehicle is skidding or a wheel slips.
•Active Park Assist is activated.
ICC LIMITATIONS
WARNING
Listed below are the system limitations for the
ICC system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only an aid to assist the
driver and is not a collision warning or
avoidance device. It is the driver’s responsi-
bility to stay alert, drive safely and be in
control of the vehicle at all times.
•The system is primarily intended for use on
straight, dry, open roads with light traffic. It
is not advisable to use the system in city
traffic or congested areas.
•This system will not adapt automatically to
road conditions. This system should be
used in evenly flowing traffic. Do not use the
system on roads with sharp curves, or on icy
roads, in heavy rain or in fog.
•As there is a performance limit to the dis-
tance control function, never rely solely on
the ICC system. This system does not cor-
rect careless, inattentive or absent-minded
driving, or overcome poor visibility in rain,
fog, or other bad weather. Decelerate the
vehicle speed by depressing the brakepedal, depending on the distance to the ve-
hicle ahead and the surrounding circum-
stances in order to maintain a safe distance
between vehicles.
•If the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill within
the limitations of the system. Once the ve-
hicle is stationary, it remains stationary and
you do not need to depress the brake pedal.
•Always pay attention to the operation of the
vehicle and be ready to manually control the
proper following distance. The ICC system
may not be able to maintain the selected
distance between vehicles (following dis-
tance) or selected vehicle speed under
some circumstances.
•Normally when controlling the distance to a
vehicle ahead, this system automatically
accelerates or decelerates your vehicle ac-
cording to the speed of the vehicle ahead. If
required, depress the accelerator to prop-
erly accelerate your vehicle when accelera-
tion is required for a lane change. Depress
the brake pedal when deceleration is re-
quired to maintain a safe distance to the
vehicle ahead due to its sudden braking or if
a vehicle cuts in. Always stay alert when
using the ICC system.
5-54Starting and driving

•The system may not detect the vehicle in
front of you in certain road or weather con-
ditions. To avoid accidents, never use the
ICC system under the following conditions:
–On roads where the traffic is heavy or
there are sharp curves.
–On slippery road surfaces such as on ice
or snow, etc.
–During bad weather (rain, fog, snow,
etc.).
–When rain, snow or dirt adhere to the
system sensor.
–On steep downhill roads (the vehicle
may go beyond the set vehicle speed and
frequent braking may result in overheat-
ing the brakes).
–On repeated uphill and downhill roads.
–When traffic conditions make it difficult
to keep a proper distance between ve-
hicles because of frequent acceleration
or deceleration.
–If there is interference by other radar
sources.
•Do not use the ICC system if you are towing
a trailer. The system may not detect a ve-
hicle ahead.
•In some road or traffic conditions, a vehicle
or object can unexpectedly come into the
sensor detection zone and cause automatic
braking. You may need to control the dis-
tance from other vehicles using the accel-
erator pedal. Always stay alert and avoid
using the ICC system when it is not recom-
mended in this section.
•The distance sensor will not detect the fol-
lowing objects:
–Stationary and slow moving vehicles.
–Pedestrians or objects in the roadway.
–Oncoming vehicles in the same lane.
–Motorcycles traveling offset in the travel
lane.
The following are some conditions in which the
sensor cannot properly detect a vehicle ahead
and the system may not operate properly:
•When the snow or road spray from traveling
vehicles reduces the sensor’s visibility.
•When excessively heavy baggage is loaded
in the rear seat or the luggage room of your
vehicle.The ICC system is designed to automatically
check the sensor’s operation within the limita-
tion of the system. When the sensor is covered
with dirt or is obstructed, the system will auto-
matically be canceled. If the sensor is covered
with ice, a transparent or translucent vinyl bag,
etc., the ICC system may not detect them. In
these instances, the ICC system may not cancel
and may not be able to maintain the selected
following distance from the vehicle ahead. Be
sure to check and clean the sensor regularly.
TIPS FOR DRIVING WITH THE ICC
SYSTEM
General notes
The following contains descriptions of certain
road and traffic conditions in which you must be
particularly attentive. In such situations, brake
if necessary. The ICC system is then deactivated
Starting and driving5-55