2017 INFINITI QX30 check engine light

Message Possible causes/consequences and solutions
[Emergency Brake
Inoperative]Forward Emergency Braking is temporarily inoperative due to a malfunction.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Radar Sensor (See
Operator’s Manual):]At least one of the following driving systems or driving safety systems is temporarily restricted or inoperative:
•Forward Emergency Braking•Intelligent Cruise Control
Possible causes:
•The sensors in the radiator trim and/or in the bumpers are dirty.•The function of the driving system and/or driving safety system is impaired due to heavy rain or snow.
A warning tone also sounds.
Once the causes listed above no longer apply, the display message goes out. All driving systems/driving safety systems are operative
again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions
2. Secure the vehicle against rolling away.
3. Switch off the engine.
4. Clean the sensors in the following locations:
- In the radiator trim
- In the front bumper
- In the rear bumper, particularly in the middle of the rear bumper.
5. Restart the engine. The display message disappears.
[SRS Malfunction Service
Required]The restraint system needs servicing. Thewarning light also lights up in the combination meter.
It is recommended you visit an INFINITI retailer for these services.
Unless checked and repaired, the Supplemental Restraint Systems and/or the pretensioner seat belt may not function properly.
WARNING
If this light is on, it could mean that the front air bag, side air bag, curtain air bag systems and/or pretensioner systems will not operate in
an accident. To help avoid injury to yourself or others, have your vehicle checked as soon as possible. It is recommended you visit an INFINITI
retailer for this service.
For further information about the restraint system, seeSupplemental Restraint System (SRS)in the1. Safety — seats, seat belts and
supplemental restraint systemsection.
Instruments and controls2-37

Driving systems
Message Possible causes/consequences and solutions
[Lane Departure Warning
Currently Unavailable See
Operator’s Manual]Lane Departure Warning is deactivated and temporarily inoperative.
Possible causes:
•The windshield is dirty in the camera’s field of vision.•Visibility is impaired due to heavy rain, snow or fog.•There have been no lane markings for an extended period.•The lane markings are worn, dark or covered, e.g. by dirt or snow.
Once the causes listed above no longer apply, the display message goes out.
Lane Departure Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Clean the windshield
[Lane Departure Warning
Inoperative]Lane Departure Warning is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Blind Spot Warning Cur-
rently Unavailable See Op-
erator’s Manual]Blind Spot Warning is temporarily inoperative. Possible causes:
•The function is impaired due to heavy rain or snow.•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The radar sensor system is outside the operating temperature range.
The yellow indicator lights also light up in the exterior mirrors.
Once the causes listed above no longer apply, the display message goes out.
Blind Spot Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Restart the engine
2-46Instruments and controls

Message Possible causes/consequences and solutions
[Blind Spot Warning Not
Available When Towing a
Trailer See Operator’s
Manual]Blind Spot Warning is deactivated while towing a trailer.
You have established the electrical connection between the trailer and your vehicle.
Press on the steering wheel to confirm the display message.
[Blind Spot Warning
Inoperative]Blind Spot Warning (BSW) is faulty.
The BSW indicator lights also light up.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Canceled] The driver’s door is open and the driver’s seat belt has not been fastened.
Repeat the parking process with the seat belt fastened and the driver’s door closed.
You inadvertently touched the steering wheel while steering intervention was active.
While steering intervention is active, make sure not to touch the steering wheel.
The vehicle has started to skid and VDC has intervened.
Use Intelligent Park Assist again later.
[Park Assist Inoperative] You have just carried out a large number of turning or parking maneuvers.
Intelligent Park Assist will become available again after approximately ten minutes.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Restart the engine.
If the display message continues to be displayed, have the system checked. It is recommended you visit an INFINITI retailer for this
service.
The parking sensor system is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Finished] The vehicle is parked. A warning tone also sounds.
The display message disappears automatically.
[ICC Off]
Intelligent Cruise Control has been deactivated (seeIntelligent Cruise Control (ICC) system (Full speed range) (if equipped)in the5.
Starting and drivingsection).
If it was not deactivated by the driver, a warning tone also sounds.
Instruments and controls2-47

•When cleaning the seat, never use gaso-
line, benzine, thinner, or any similar mate-
rials.
•If any malfunctions are found or the heated
seat does not operate, turn the switch off
and have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service.
The front seats are warmed by built-in heaters.
The switches are located on the center console
and can be operated independently, for the
left-hand side seat and for the right-hand side
seat.
The three red indicator lights in the button
indicate the heating level you have selected The
system automatically switches from level 3 to
level 2 after approximately eight minutes The
system automatically switches from level 2 to
level 1 after approximately ten minutes. The
system automatically switches off approxi-
mately 20 minutes after it is set to level 1
1. Turn the ignition switch to the ON position.
NOTE
The seat heater can only be activated when
the ignition switch is in the ON position.2. Start the engine.
3. Select the heat range:
•To switch on: press button1repeatedly
until the desired heating level is set.
•To switch off: press button1repeatedly
until all the indicator lights turn off.
NOTE
If the battery voltage is too low, the seat heating
may switch off.
NIC2634
2-70Instruments and controls

Symptom Possible causeRemedy
The engine
cannot be
started using
the keyThe on-board
voltage is too
low
•Switch off non-essential consumers, e. g. seat heating or interior lighting, and try to start the engine again
If this does not work:
•Check the starter battery and charge it if necessary (seeBatteryin the8. Do-it-yourselfsection)
or
•Jump-start the vehicle (seeJump startingin the6. In case of emergencysection)
or
•Have the system checked. It is recommended you consult an INFINITI retailer.
You have lost
a key—
•Have the key deactivated. It is recommended you visit an INFINITI retailer for this service.•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well
You have lost
the emer-
gency key
element
•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well.
Pre-driving checks and adjustments3-13

1. Make sure that the windshield wipers are
switched off.
2. Pull the hood lock release lever
1, located
below the instrument panel on the driver’s
side; the hood will spring up slightly.3. Push the lever
2at the front of the hood,
to the left with your fingertips and raise the
hood.4. Insert the support rod3into the slot4on the underside of the hood.
5. When closing the hood, replace the support
rod in its original position
5, slowly lower
the hood to about8–12in.(20–30cm)
above the hood lock, then let it drop. Make
sure the hood is securely latched.
WARNING
•Make sure the hood is completely closed
and latched before driving. Failure to do so
could cause the hood to fly open and result
in an accident.
•If you see steam or smoke coming from the
engine compartment, to avoid injury do not
open the hood.
NDI1603NDI1627NDI1605
HOOD
3-14Pre-driving checks and adjustments

•Recommendation for air distribution in win-
ter: select theandsettings.
Recommendation for air distribution in sum-
mer: select the
orandsettings.
•Only use theWindshield demistingfunc-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, e. g
if there are unpleasant outside odors or
when in a tunnel. The windows could other-
wise mist up as no fresh air is drawn into the
vehicle in air-recirculation mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of the
various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-clockwise
to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidi-
ficationfunction, the air inside the vehicle will
not be cooled. The air inside the vehicle will
also not be dehumidified. The windows can mist
up more quickly. Therefore, only deactivate the
Cooling with air dehumidificationfunction
briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Display screen, heater and air conditioner, and audio system4-45

•Use thefunction to adopt the tem-
perature settings on the driver’s side for the
front-passenger side as well. The indicator
lamp in the
button goes out.
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the center display
(see separate operating instructions). You
will see the current settings of the various
climate control functions.
Idle Stop/Start function
During automatic engine switch-off, the Climate
control only operates at a reduced capacity. If
you require the full climate control output, you
can switch off the Idle Stop/Start function by
pressing the ECO button (seeIdle Stop/Start
System (if equipped)in the5. Starting and
drivingsection).
Switching automatic climate control
on/off
When the climate control is switched off, the air
supply and air circulation are also switched off.
The windows could mist up. Therefore, only
switch off climate control briefly.
Make sure the ignition switch is in the ON
position.To activate
:
Press thebutton The indicator lamp in
thebutton lights up. Airflow and air
distribution are set to automatic mode.
or
Press the
button. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton lights up.
NOTE
Automatic climate control: switch on climate
control primarily using the
button.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidifi-
cationfunction, the air inside the vehicle will not
be cooled. The air inside the vehicle will also not
be dehumidified. The windows can mist up more
quickly. Therefore, only deactivate theCooling
with air dehumidificationfunction briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.
Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Display screen, heater and air conditioner, and audio system4-49