2017 INFINITI QX30 service

Anti-lock Braking System (ABS) warning
lightSeat belt (driver and front passenger)
warning lightHigh beam indicator light
Brake warning light (red)Supplemental Restraint System (SRS) air
bag warning lightRear fog light indicator light
Low tire pressure warning light*Low fuel warning lightSide light indicator light
Malfunction indicator light (yellow)Turn signal/hazard indicator lightsVehicle Dynamic Control (VDC) warning
light
Distance warning light*Low beam indicator lightFront passenger air bag status light**
Parking brake warning light (red)Vehicle Dynamic Control (VDC) OFF indica-
tor light
Parking brake warning light (yellow)Front fog light indicator light*
Coolant warning lightHigh beam assist indicator light * *: if equipped**: located above heater and air conditioner controls
Some indicators and warnings are also dis-
played in the vehicle information display be-
tween the speedometer and tachometer see
Vehicle information displayin the
2. Instruments and controls section.CHECKING LIGHTS
With all doors closed, apply the parking brake,
fasten the seat belts and place the ignition
switch in the ON position without starting the
engine. The following lights (if so equipped) will
come on, ,
,,,,
,,,,. These lights
should go out within a few seconds after start-
ing the engine. If any light fails to come on or
operates in a way other than described, it may indicate a burned out bulb and/or a system
malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
WARNING LIGHTS
Also see
Vehicle information display later in
this section.
WARNING LIGHTS, INDICATOR LIGHTS AND
AUDIBLE REMINDERS
2-8Instruments and controls

Anti-lock Braking System
(ABS) warning light
When the ignition switch is in the ON position,
the ABS warning light illuminates to indicate
that the ABS is operational. The light then turns
off within a few seconds after the engine is
started.
If the ABS light comes on while the engine is
running, it may indicate the anti-lock braking
system is not functioning properly. Have the
system checked. It is recommended that you
visit an INFINITI retailer for this service.
If the ABS warning light comes on while driving,
it may indicate the ABS is not functioning
properly. Observe the additional display mes-
sages (if any) in the vehicle information display.
Have the system checked by an INFINITI retailer.
If an ABS malfunction occurs, the anti-lock
function is turned off. The brake system then
operates normally, but without anti-lock assis-
tance (seeBrake system in the5. Starting and
driving section).
BRAKE warning light (red)
WARNING
•Your brake system may not be working
properly if the warning light is on. Driving
could be dangerous. If you judge it to be
safe, drive carefully to the nearest service
station for repairs. Otherwise, have your ve-
hicle towed because driving it could be dan-
gerous.
•Pressing the brake pedal when the ignition
switch is not in the ON position and/or when
the brake fluid level is low may increase the
stopping distance and braking will require
greater pedal effort as well as pedal travel.
•If the brake fluid level is below the minimum
or MIN mark on the brake fluid reservoir, do
not drive until the brake system has been
checked. It is recommended that you visit
an INFINITI retailer for this service.
When the ignition switch is placed in the ON
position, the light remains illuminated and
turns off when the engine is started. If the light
illuminates at any other time, it may indicate
that the brake system is not functioning prop-
erly. If the BRAKE warning light illuminates, stop the vehicle immediately and contact an
INFINITI retailer.
This light functions for both the parking brake
and the foot brake systems.
Low tire pressure warning
light (if equipped)
Your vehicle is equipped with a Tire Pressure
Monitoring System (TPMS) that monitors the
tire pressure of all its tires.
The low tire pressure warning light warns of low
tire pressure or indicates that the TPMS is not
functioning properly.
When the ignition switch is in the ON position,
the Low tire pressure warming light illuminates
to indicate that the system is operational. The
light then tuns off within a few seconds after
the engine is started.
Low tire pressure warning
:
If the vehicle is being driven with low tire pres-
sure, the warning light will illuminate. A tire
pressure warning message also appears in the
vehicle information display.
When the low tire pressure warning light illumi-
nates, you should stop and adjust the tire pres-
sure of all 4 tires to the recommended COLD tire
Instruments and controls2-9

pressure shown on the Tire and Loading Infor-
mation label located in the driver’s door open-
ing, seeTire and loading information label in
the 9. Maintenance and Schedules section.
The low tire pressure warning light does not
automatically turn off when the tire pressure is
adjusted. After the tire is inflated to the recom-
mended pressure, the vehicle must be driven at
speeds above 16 MPH (25 km/h) to activate the
TPMS and turn off the low tire pressure warning
light. Use a tire pressure gauge to check the tire
pressure.
The low tire pressure warning message appears
each time the ignition switch is placed in the ON
position as long as the low tire pressure warn-
ing light remains illuminated.
For additional information, see Vehicle infor-
mation display later in this section and Tire
Pressure Monitoring System (TPMS) in the
5. Starting and driving section.
TPMS malfunction
:
If the TPMS is not functioning properly, the low
tire pressure warning light will flash for approxi-
mately 1 minute when the ignition switch is
placed in the ON position. The light will remain
on after 1 minute. Have the system checked. It is
recommended that you visit an INFINITI retailer for this service. The low tire pressure warning
does not appear if the low tire pressure warning
light illuminates to indicate a TPMS malfunc-
tion.
For additional information, see
Tire Pressure
Monitoring System (TPMS) in the5. Starting
and driving section.
WARNING
•Radio waves could adversely affect electric
medical equipment. Those who use a pace-
maker should contact the electric medical
equipment manufacturer for the possible in-
fluences before use.
•If the light does not illuminate with the ig-
nition switch pushed ON, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
•If the light illuminates while driving, avoid
sudden steering maneuvers or abrupt brak-
ing, reduce vehicle speed, pull off the road
to a safe location and stop the vehicle as
soon as possible. Driving with under-
inflated tires may permanently damage the
tires and increase the likelihood of tire fail-
ure. Serious vehicle damage could occur
and may lead to an accident and could result
in serious personal injury or death. Check the tire pressure for all four tires. Adjust the
tire pressure to the recommended COLD tire
pressure shown on the tire placard, located
in the driver’s door opening, to turn the low
tire pressure warning light off. If the light
still illuminates while driving after adjust-
ing the tire pressure, a tire may be flat. If you
have a flat tire, replace it with a replacement
tire as soon as possible.
•If a replacement tire is mounted or a wheel
is replaced without a TPMS sensor tire pres-
sure will not be indicated, the TPMS will not
function and the low tire pressure warning
light will flash for approximately 1 minute.
The light will remain on after 1 minute. Have
your vehicle’s tires replaced and/or TPMS
system reset as soon as possible. It is rec-
ommended you visit an INFINITI retailer for
these services.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
CAUTION
•The TPMS is not a substitute for the regular
tire pressure check. Be sure to check the tire
pressure regularly.
2-10Instruments and controls

•If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS may
not operate correctly.
•Be sure to install the specified size of tires
to all four wheels correctly.
Malfunction Indicator light (MIL)
(yellow)
When the ignition switch is turned to the ON
position, the yellow Malfunction Indicator light
illuminates. This means that the system is
operational.
If the yellow engine malfunction indicator light
lights up while the engine is running, there may
be a fault, for example:
•In the engine management
•In the fuel injection system
•In the exhaust system
•In the ignition system (for vehicles with
gasoline engines)
•In the fuel system
•In other monitored items, for example the
automatic transmission.The emission limit values may be exceeded and
the engine may be running in emergency mode.
CAUTION
Continued vehicle operation without having
the engine control system checked and re-
paired as necessary could lead to poor drive-
ability, reduced fuel economy and possible
damage to the engine control system.
Incorrect setting of the engine control system
may lead to non-compliance of local and na-
tional emission laws and regulations.
Have the vehicle checked as soon as possible. It
is recommended you visit an INFINITI retailer for
this service.
Distance warning light (if
equipped)
This light illuminates if the distance to the
vehicle in front is too small for the speed
selected.
If a warning tone also sounds, you are ap-
proaching a vehicle or stationary obstacle in
your line of travel at too high a speed. For
additional information see Forward emergency
braking (FEB) system (if equipped) in the
5. Starting and driving section.
Electric parking brake
warning light
The red indicator illuminates when the electric
parking brake is engaged.
If the red indicator light for the electric parking
brake flashes or is lit and/or the yellow warning
light for the electric parking brake is lit, observe
the additional messages displayed in the ve-
hicle information display.
For further parking brake operation information
seeParking brake in the3. Pre-driving checks
and adjustments section.
Seat belt (driver and front
passenger) warning light
The seat belt warning light reminds you to
fasten your seat belts. The light illuminates if
the engine is started, all doors are closed and
the driver’s and/or front passenger’s seat belt
is unfastened. It will remain illuminated until
the driver and/or front passenger fastens their
seat belt. A chime will sound once the vehicle is
in motion, seeSeat belt reminder chime later
in this section. See Seat beltsin the1. Safety
— seats, seat belts and supplemental restraint
system section for precautions on seat belt
usage.
Instruments and controls2-11

The seat belt warning light may also illuminate
if there are objects on the front passenger seat.
Remove the objects and stow them in a safe
place.
If the seat belt warning light flashes, together
with an intermittent warning tone, this means
that the driver or passenger has not fastened
their seat belt, and the speed of the vehicle is
exceeding 15 MPH (25 km/h).
Supplemental Restraint System
(SRS) air bag warning light
WARNING
If the supplemental air bag warning light is on,
it could mean that the front air bag, driver’s
knee air bag, side air bag, curtain air bag
and/or pretensioner systems will not operate
in an accident. To help avoid injury to yourself
or others, have your vehicle checked by an
INFINITI retailer as soon as possible.
When the ignition switch is in the ON position,
the Supplemental Restraint System (SRS) air
bag warning light illuminates to indicate that
the system is operational. The light then tuns
off within a few seconds after the engine is
started. If any of the following conditions occur, the
front air bag, front seat-mounted side-impact
air bag, roof-mounted curtain air bag and pre-
tensioner systems need servicing:
•The supplemental air bag warning light re-
mains on for longer than a few seconds once
the engine is running.
•The supplemental air bag warning light
flashes intermittently.
•The supplemental air bag warning light does
not come on at all.
It is recommended you visit an INFINITI retailer
for these services. Unless checked and re-
paired, the supplemental restraint system (air
bag system) and/or the pretensioner systems
may not function properly. For additional infor-
mation, refer to Supplemental Restraint Sys-
tem (SRS) in the1. Safety — seats, seat belts
and supplemental restraint system section.
Coolant warning light
WARNING
If the coolant warning light is lit, the engine
may not be being cooled sufficiently and may
be damaged.
Never drive with an overheated engine. Driving
when your engine is overheated can cause some fluids which may have leaked into the
engine compartment to catch fire.
In addition, steam from an overheated engine
can cause serious burns, which can occur just
by opening the hood.
There is a risk of injury
If the red coolant warning light lights up while the
engine is running and the coolant temperature
gauge is at the start of the scale, the temperature
sensor for the coolant temperature gauge is faulty.
The coolant temperature is no longer being moni-
tored. There is a risk of engine damage if the
coolant temperature is too high.
Stop the vehicle immediately, paying attention
to road and traffic conditions, and switch off the
engine. Do not continue driving under any
circumstances.
Consult an INFINITI retailer.
If the red coolant warning light comes on while
the engine is running, with or without an ac-
companying warning tone, it could mean that:
•The coolant level is too low.
•If the coolant level is correct, the airflow to
the engine radiator may be blocked or the
electric engine radiator fan may be malfunc-
tioning.
2-12Instruments and controls

system checked. It is recommended you visit an
INFINITI retailer for these services.
If an abnormality occurs in the system, the VDC
system function will be canceled, but the ve-
hicle is still driveable. For additional informa-
tion, seeVehicle Dynamic Control (VDC)
system in the5. Starting and driving section.
WARNING
VDC should remain on unless freeing a vehicle
from mud or snow.
While the VDC system is operating, you might
feel a slight vibration or hear the system work-
ing when starting the vehicle or accelerating,
but this is normal.
Front fog light indicator light (if
equipped)
The light comes on when the front fog lights are
switched on (see Fog light switch (If so
equipped) later in this section).
High beam assist indicator light
(if equipped)
The indicator light illuminates when the head-
lights come on while the headlight switch is in
the AUTO position with the high beam selected.
This indicates that the high beam assist system
is operational. (See 2-63.)
High beam indicator light
This blue light comes on when the headlight
high beams are on and goes out when the low
beams are selected.
The high beam indicator light also comes on
when the passing signal is activated.
Rear fog light indicator light
The light comes on when the rear fog light is
switched on (see Fog light switch (If so
equipped) later in this section).
Side light and headlight
indicator light
This light comes on when the side light or
headlight position is selected, see Headlight
and turn signal switches later in this section
for further details.
/Front passenger air
bag status light
The front passenger air bag status light ()
located on the center console above the shift
lever will illuminate when the front passenger
air bag is turned OFF. When the front passenger
air bag is turned on, the front passenger air bag
status light ON (
) will illuminate.
For more details, see Front passenger air bag
and status light in the1. Safety — seats, seat
belts and supplemental restraint system sec-
tion.
AUDIBLE REMINDERS
Parking brake reminder chime
A chime will sound when driving away if the
parking brake has not been released. Stop the
vehicle and release the parking brake.
Light reminder chime
With the ignition switch placed in the OFF
position, a chime sounds when the driver’s door
is opened if the side lights are on. Turn the
headlight control switch off before leaving the
vehicle.
2-14Instruments and controls

2. Press theorbutton to select
[Lane Departure Warning].
3. Press the button on the steering wheel.
The current selection is displayed.
4. Press the to confirm.
5. Press the
orbutton to set [Off],
[Standard] or [Adaptive].
6. Press the button to save the setting.
For further information about Lane Departure
Warning, see Lane departure warning (LDW)
system (if equipped) in the 5. Starting and
driving section.
Service menu ([Serv.])
Depending on the equipment fitted in the ve-
hicle, you have the following options in the
[Serv.] menu:
•Calling up display messages in the message
memory (see Message memory later in this
section).
•Restarting the tire pressure monitoring sys-
tem (TPMS) (see Restarting TPMS in the5.
Starting and driving section.
•Checking the tire pressure electronically (see
Checking the tire pressure electronically in
the 5. Starting and driving section).
•Calling up the service due date (see Main-
tenance service messages in the
9. Maintenance and Schedules section).
Settings menu
Depending on the equipment fitted in the ve-
hicle, in the [Settings] menu you have the
following options:
•Changing the instrument cluster settings.
•Changing the light setting.
•Changing the vehicle setting.
•Changing the convenience setting.
•Restoring the factory setting.
Instrument cluster
:
Unit of measurement for distance: The Display
unit Speed-/odometer function allows you to
choose whether certain displays appear in kilo-
meters or miles in the vehicle information dis-
play.
NIC2874NIC2731
2-24Instruments and controls

1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Display Unit Speed-/Odometer] func-
tion.
You will see the selected setting: [miles] or
[km].
5. Press the button to change the setting.
The selected unit of measurement for distance
applies to:
•Digital speedometer in the [Trip] menu.
•Total distance recorder and the trip meter.
•Trip computer.
•Current fuel consumption and approximate
range.
•Navigation instructions in the [Navi] menu.
•Cruise control.
•Speed limiter.
•Intelligent cruise control (ICC).
•Maintenance service interval display. Switching the additional speedometer on/off.
The [Speedometer (mph)] or [Speedometer (km/
h)] function allows you to choose whether the
vehicle information display in the status area
shows the speed in MPH or in km/h instead of
the outside temperature.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Speedometer (mph)] or [Speedometer
(km/h)] function.
You will see the selected setting: [On] or
[off].
5. Press the button to change the setting.
Selecting the permanent display function.
You can determine whether the vehicle informa-
tion display permanently shows the outside
temperature or the speed in MPH.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu. 3. Press to confirm.
4. Press the
orbutton to select
the [Outside Temperature] function.
You will see the selected setting: [outside
temperature] or [Speedometer (mph)].
5. Press the button to save the setting.
Lights
Switching the Adaptive Front Lighting System
on/off:
1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Adaptive front lighting system] function.
If the [Adaptive front lighting system] func-
tion has been switched on, the cone of light
and the
symbol in the vehicle infor-
mation display are shown in orange.
5. Press the button to save the setting.
Instruments and controls2-25