2017 Hyundai Ioniq Electric change time

IONIQ
electricwww.hyundai.com
Roadside Assistance:
1-800-243-7766
Consumer Affairs:
1-800-633-5151
Sirius
XM®
Radio:
1-800-967-2346
Blue Link:
1-855-2BLUELINK
(1-855-225-8354)
HYUNDAI
Quick Reference Guide
☐Tire Pressure Monitoring System (TPMS) - page 39☐Unlocking vehicle - page 02
• To activate wipers, move the switch down
to one of the three positions (INT, LO, HI).
• To adjust "INT" speed, move switch.
• To spray washer fluid, pull lever toward you.
• Push lever up for a single wiper pass.
☐Windshield Wiper / Washer - page 10


INT
LO
HI MIST
OFF
UNLOCK
LIFTGATE UNLOCK LOCK
PANIC
NOTE: Tire pressure may vary in colder temperatures causing the low
tire pressure indicator
to illuminate. Inflate tires according to the Tire
Pressure Label located on the driver’s side door pillar.
LOW TIRE PRESSURE INDICATOR /
TPMS MALFUNCTION INDICATOR
NP150-AE171
(Rev 02/04/17)
Printing 02/07/17
Looking For more detailed information?
This Quick Reference Guide does not replace your vehicle’s
Owner’s Manual. If you require additional information or are unsure of a specific issue, we
recommend that you always refer to the vehicle’s Owner’s Manual or contact your authorized
Hyundai dealer. The information contained in this Quick Reference Guide is correct at the time of
printing; however, specifications and equipment can change without notice. No warranty or
guarantee is being extended in this Quick Reference Guide, and Hyundai reserves the right to
change product specifications and equipment at any time without incurring obligations. Some
vehicles are shown with optional equipment.
MAINTENANCEScheduled Maintenance Normal Usage Severe Usage*Tire Rotation Perform 5,000 Perform 5,000
Climate Control Air Filter
(for Evaporator and Blower Unit)Replace 15,000 Replace More Frequently
Air Conditioning Refrigerant Inspect 15,000 Inspect Same As Normal
Brake Hoses & Lines Inspect 15,000 Inspect Same As Normal
Drive Shafts & Boots Inspect 15,000 Inspect 7,500
Front Disc Brake/Pads, Calipers & Rotors Inspect 15,000 Inspect More Frequently
Rear Brake Disc/Pads Inspect 15,000 Inspect More Frequently
Steering Gear Box, Linkage & Boots/
Lower Arm Ball Joint, Upper Arm Ball JointInspect 15,000 Inspect More Frequently
Suspension Mounting Bolts Inspect 15,000 Inspect Same As Normal
Brake fluid Inspect 30,000 Inspect Same As Normal
Coolant1st Replace 120,000 or 120 mos.
Add’l Replace 30,000 or 24 mos.Replace Same As Normal
Reduction Gear Fluid Inspect 37,500 or 30 mos. Replace 75,000
*Check the engine oil regularly between recommended oil change. Hyundai recommends Quaker State oil.
*See Owner’s Manual for details.
☐How to
Defrost - page 25-27

1 Press the front defrost button.
2 Set to warmest temperature setting.
3 Set to highest fan speed.
WALK THE CUSTOMER THROUGH EACH OF
THE FOLLOWING KEY DELIVERY FEATURES☐ BLUE LINK - pages 33-35
- Assist with creating MyHyundai.com account
- Assist with Blue Link enrollment
- Show Blue Link Users Manual & tear out Voice
Commands/Quick Tip Card
- Encourage customers to press the Blue link button

Quick Reference Guide I 15
14 I Quick Reference Guide
IONIQ ELECTRIC HYUNDAI
Standard Programming To train most devices, follow these instructions:
1. For the first-time programming, press and hold the two outside
buttons, HomeLink
® Channel 1 and Channel 3 buttons, until the
indicator light begins to flash (after 10 seconds). Release both
buttons. Do not hold the buttons for over 20 seconds.
2. Position the end of your hand-held transmitter 1-3in. (2-8cm)
away from the HomeLink
® buttons while keeping the indicator
light in view.
3. Simultaneously press and hold both the HomeLink
® and the
hand-held transmitter button. DO NOT release the buttons until
step 4 has been completed.
4. While continuing to hold the buttons, the red indicator Status LED
will flash slowly and then rapidly after HomeLink
® successfully
trains to the frequency signal from the hand-held transmitter.
Release both buttons.
For more detailed information, please refer to your Owner’s Manual, or
visit www.homelink.com or call (800) 355-3515.
HOMELINK WIRELESS CONTROL SYSTEM
SEAT WARMER (Front seat)
Each time you push the button,
the setting is changed as follows:OFFMIDDLE HIGH
LOW
FEATURES AND CONTROLS
WIRELESS CELLULAR PHONE CHARGING SYSTEM
If you want to turn it off immediately,
press and hold the button.There is a wireless cellular phone
charging system in front of the cup
holders. The system operates with
all doors closed, and the Engine
Start/Stop button in the ACC/ON/
START position. Wireless charging
system can be disabled in the
instrument cluster settings menu.
NOTE:The wireless cellular phone charging system supports only the
Qi-enabled cellular phones (
).
NOTE:
Do not place any metallic items such as coins, keys on the
charger. Avoid placing credit cards on the charger as they may be
damaged by the magnetic field.
The charging area may be warm while using wireless charging.

Quick Reference Guide I 25
24 I Quick Reference Guide
IONIQ ELECTRIC HYUNDAI
FEATURES AND CONTROLS
8 Air intake control button9 Mode selection button10 Driver only button11 HEAT button12 EV button13 Climate control information screen
1 Temperature control knob2 Fan speed control knob3 AUTO (automatic control) button4 OFF button5 Front windshield defrost button6 Rear window defrost button7 Air conditioning button
ELECTRIC VEHICLE SYSTEM MODES
AUTOMATIC CLIMATE CONTROL
3
5
6
11
7
8
4
9
13
1
12
10
2
1 Range : You can check reachable areas, risky areas and
unreachableareas.(type B only)2 Nearby stations : Searches for every electric charging station of
current location.3 Energy information : Displays battery information and electricity use.4 Drive mode settings : Climate Control, Coast Energy Regeneration,
and Maximum Speed Limit can be set for three different drive modes.
5 ECO driving : ECO Level information and ECO Driving history are
displayed.6 Charging/Climate settings : A departure time and climate temperature

can
be set so battery charging and climate temperature adjustment

are automatically completed before the set departure time.
7 EV settings : You can change the settings for charging current.
(for charging current, EV warnings, and drivable routes : type B)
Press the EV menu at the AVN home screen
or the EV button on the airconditioning
button panel to enter the EV mode.
Type B
Type B Type A
Type A
3
3
5
5
6
6
7
7
4
4
1
2
2

Quick Reference Guide I 29
28 I Quick Reference Guide
IONIQ ELECTRIC HYUNDAI
MULTIMEDIA
1 VOLUME (VOL + / -
)

Increases or decreases the
volume.
2 SEEK / PRESET ( / ) Changes station.3 MODE Changes the audio source.4 MUTE ( )
Mute the sound.
Making a call using voice recognition:
Press
button on the steering
wheel control to activate voice
recognition.
Press and hold
button to end
voice recognition.
Calling by Name:
1. Press the
button.
2. Say the following command:
• “Call ”: Connects the call to John.
• “ Call on Other>”: Connects the call to John’s Mobile, Work, Home, or
Other phone number.
Dialing by Number:
1. Press the button.
2. Say “Dial Number.”
3. Say desired phone number. For complete list of commands, refer
to your Owner’s Manual.
STEERING WHEEL AUDIO CONTROL
To Answer a Call:
• Press the
button on the steering wheel.
To Reject a Call:
• Press the button on the steering wheel.
To Adjust Ring Volume:
• Use the VOLUME buttons on the steering wheel.
To Transfer a Call to the Phone
(Private call on handset – do not use while driving):
• Press and hold the
button on the steering wheel until the
audio system transfers a call to the phone.
To Finish a Call:
• Press the
button on the steering wheel.
In the following situations you or the other party may have difficulty
hearing each other:
1. Keep the Bluetooth®
volume to a low level. High level volume may
result in distortion and echo.
2. When driving on a rough road, high speeds and/or with the window
open.
3. When the air conditioning vents are facing the microphone and/or
when the air conditioning fan is at the max speed.
Steering wheel bluetooth
® control
1 CALL Places and transfers calls.2 END Ends calls or cancels functions.
Bluetooth
® PHONE CALL OPERATIONAL TIPS
NOTE:
Android Auto and Apple CarPlay are also available.
2
1
23
1
4

Quick Reference Guide I 35
34 I Quick Reference Guide
IONIQ ELECTRIC HYUNDAI
MULTIMEDIA
You can download the MyHyundai with Blue Link app
to your compatible smart phone from the following
sites: • iPhone
® — Apple
® App Store
• Android
™ — Google Play
™
Remote Climate Control MyHyundai with Blue Link App• Remote Start will automatically shut off after 15 minutes or after selected
engine timer runs out.
• To continue to operate the vehicle, the proximity key must be inside
the vehicle with the driver, prior to pressing the brake and being able to
move the gearshift from the P (Park) position.Remember:
Scan to learn more about
the MyHyundai mobile
app and Remote
features
Visit HyundaiBlueLink.com FAQs
to see a list of compatible devices.
NOTE:
Remote Climate Control is not available on all models. Remote
Climate Control is only available for Push Start equipped vehicle with an
Automatic Transmission. Remote Climate Control with Climate Control
additionally requires Fully Automatic Temperature Control.
Preconditions: • Ignition is OFF
• Alarm is armed (i.e., vehicle locked by key fob Remote Door Lock)
• Gearshift level is in the P (Park) position
• Brake pedal is not depressed
• Engine hood is securely closed
• All the doors are closed and locked
• The tailgate or trunk lid is closed
• The security / panic system is not activated
• The proximity key is not inside the vehicle
• The battery power is not low
• Vehicle is located in an open area
• It has been less than 4 days since last vehicle ignition off
• Vehicle located in area with good cell receptionRemote Climate Control will terminate: • After 15 minutes or after selected engine timer runs out
• Brake is pressed without the proximity key inside the vehicle
• Alarm is triggered without the proximity key inside the vehicle
• Door / trunk is opened from inside the vehicleNotice:
Laws in some communities may restrict the use of the features
that remotely start the engine. For example, some laws may require a
person using the remote start feature to have the vehicle in view when
doing so, or limit the length of time a vehicle engine may idle. Please
check local and state regulations for any requirements and restrictions
on remote starting of vehicles and engine idling time.

WARNING!
Do not remote start vehicle in an enclosed environment (i.e., closed garage). Prolonged operation
of a motor vehicle in an enclosed environment can cause a harmful build-up of carbon monoxide.
Carbon monoxide is harmful to your health. Exposure to high levels of carbon monoxide can
cause headaches, dizziness or in extreme cases unconsciousness and / or death. Do not leave
children or animals unattended in a vehicle while using the remote start function.
CAUTION!If the vehicle’s windshield wipers are left on when the vehicle was last driven, then the wipers will
turn on if the remote start function is activated. To avoid damage to the wiper blades (i.e., due to
heavy ice or snow accumulated on the windshield), please always turn the vehicle’s windshield
wipers off when parking the vehicle.
Remote Climate Control* enables you to remotely enable climate
control and turn on the front window defroster, ensuring a warm or
cool car is ready to go when you are.
•
To use this feature, you must have a Blue Link Personal
Identification Number (PIN). To create or change your PIN,
log in to www.MyHyundai.com.

Quick Reference Guide I 37
36 I Quick Reference Guide
IONIQ ELECTRIC HYUNDAI
Use the input jack to connect an
external audio device and listen
to it through the audio system in
your vehicle.
iPod
® is a trademark of Apple, Inc.
Basic features on map screen1 Place button : Go to the Place menu.2 Home button : Go to the Home screen.3 Map button : Change the map view mode.4 NAV volume button : Adjusts the volume.5 Zoom in button : Zoom the map view screen in.6 Map scale display : Set the zoom level automatically according
to the guidance.7 Zoom out button : Zoom the map view screen out.8 Quick menu button : Quick and easy selection of a destination
and options.9 NAV button : Enter the navigation menu screen.10 Map scroll mark : Touch to scroll the map.
11 Destination button : Quick and easy selection of a destination
from the map screen.12 Waypoint button : Set a waypoint to the current route.13 Save button : Save frequently used address to address book.14 POI button : Find a POI(Point Of Interest) around the current position.15 Vehicle position mark : View the vehicle’s current position on
the map screen.
15
11
10
12
13
14
234
1
567
8
Destination search screen1 Address : Set destination by address search.2 Previous destinations : Select from previously inputted addresses
and POIs.3 Local search : Runs Google Local Search.4 POI categories : Select the desired item in the sub-categories.5 Charging stations : Select the desired destinations among the
searched charging stations.6 Restaurants : Select the desired destination among the searched
restaurants.7 Emergency : Select the desired destination among the searched
emergency facilities.8 Address Book : Search the destination with the address book.9 Phone Number : Search the destination by phone number.10 Freeway Exit/Entrance : Type freeway name and exit/entrance to
search by freeway exit/entrance.11 Intersection : Type 1st Street name, the State, 2nd Street name.12 Coordinates : You can find a destination by entering the
coordinates of latitude and longitude.
Press [NAV] on the map screen and, finds a destination by using the
[Destination] menu.
2
3
4
15
6
7
8
9
10
11
12
NAVIGATION
MULTIMEDIA
9
AUX, USB AND iPod
® PORT

Quick Reference Guide I 45
44 I Quick Reference Guide
IONIQ ELECTRIC HYUNDAI LANE DEPARTURE WARNING SYSTEM (LDWS)
The Lane Departure Warning System
detects the lane on the road and
warns the driver if the vehicle leaves
the lane. The system operates when
the vehicle speed is over 40 mph.
• To turn on the LDWS, press the
LDWS switch.
• To turn off the LDWS, press the
switch again.
2
The BSD (Blind Spot Detection)
system uses a radar sensor to alert
the driver while driving.
It monitors the rear area of the vehicle
and provides information to the driver.1 Blind Spot Detection2 Lane Change Assist3 Rear Cross Traffic Alert
The system will activate if vehicle speed exceeds 20 mph.• To turn on the BSD, press the BSD
button (indicator illuminated).
• To turn off the BSD, press the BSD
button again.
When the vehicle is in R (Reverse), the system provides an alert if a
vehicle is approaching from the sides.Rear Cross Traffic AlertBLIND SPOT DETECTION SYSTEM (BSD)
3
1
DRIVING
DRIVE MODE INTEGRATED CONTROL SYSTEM
You can select the drive mode
according to your preference or the
road condition.
The system initializes to the NORMAL
mode (except ECO mode)
after the vehicle is restarted.
Each time you press the button, the
drive mode is changed as follows :
Eco mode system helps to improve fuel efficiency. When the ECO
mode system is activated, the vehicle acceleration, gear shift points
and air conditioning perfomance will be reduced to conserve the fuel
consumption.
ECO modeNormal mode provides regular daily driving performance with some
fuel efficiency.NORMAL modeSport mode provides a sporty feel and may have heavier steering
effort. In Sport mode, the fuel efficiency may decrease. SPORT mode
NORMAL

ECO
SPORT
Normal mode is not displayed on
the instrument cluster.

Quick Reference Guide I 47
46 I Quick Reference Guide
IONIQ ELECTRIC HYUNDAI
DRIVING
AUTONOMOUS EMERGENCY BRAKING (AEB)
The Autonomous Emergency Braking (AEB)
system is designed to detect and monitor the
vehicle ahead or detect a pedestrian in the
roadway through radar signals and camera
recognition to warn the driver that a collision is
imminent, and if necessary, apply emergency
braking.
To activate the system,
Select “User Settings
Driving Assist
Autonomous Emergency Braking”
The system deactivates, when the system
setting is cancelled.
1 To turn on/off the cruise control.2 To resume or increase the cruise
control speed.3 To set or decrease the cruise
control speed.4 To cancel the cruise control. The Cruise Control system allows you to
program the vehicle to maintain a
constant speed without depressing the
accelerator pedal.
If your vehicle is equipped with Advanced Smart Cruise Control and you
wish to eliminate the vehicle distance function, you can change cruise control
setting to a standard setting. Press the Cruise Control button on the steering
wheel to turn on the Cruise Control. Then press and hold the vehicle distance
button for more than 2 seconds to toggle between the Smart Cruise Control
(SCC) and Cruise Control (CC) mode. Please refer to your Owner’s Manual for
more information.
CRUISE CONTROL / SMART CRUISE CONTROL
Setting Vehicle Distance (Smart
Cruise Control only)This system allows you to program
the vehicle to maintain constant
speed and distance without
depressing the accelerator or brake
pedal.
The vehicle to vehicle distance
1 will
automatically activate when you set
the cruise speed
2.
Each time the vehicle distance set
button is pressed, the vehicle to
vehicle distance changes as
following:
2
1
Distance 2 Distance 3 Distance 4
(Longest)
Distance 1(Shortest)
2341