2017 FIAT FIORINO technical data

CHANGING AN EXTERIOR BULB
For the type of bulb and corresponding power rating,
see the paragraph "Changing a bulb".
FRONT LIGHT CLUSTERS
The front light clusters fig. 156 contain sidelight,
dipped beam, main beam and direction indicator
bulbs.
The bulbs are arranged inside the light cluster as
follows:
A Side lights/tail lights and main/dipped beam
headlights;
B Direction indicators.
SIDE LIGHTS - TAIL LIGHTS
To change the bulb, proceed as follows:
remove the protective lid A fig. 156;
turn the bulb holder A fig. 157 anticlockwise and
remove it;
remove the bulb B and replace it;
refit the new bulb, insert the bulb holder A
fig. 157 again and then refit the protective lid A
fig. 156 correctly.
DIPPED/MAIN BEAM HEADLIGHTS
To change the bulb (double filament), proceed as
follows:
remove the protective lid A fig. 156;
release the bulb holder clip;
remove the bulb A fig. 158 from connector B and
replace it;
refit the new bulb by inserting it on connector B
and then make the contour of the metallic part
mate with the grooves obtained on the headlight
parabola;
fig. 156F0T0093fig. 157F0T0094
170
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

refit the bulb holder clip and refit the protective
lid A fig. 156 correctly.
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
turn the protective lid B fig. 156 anticlockwise;
remove the bulb A fig. 159 and replace it;
refit the protective lid B correctly.
Side lights
To change the bulb, proceed as follows:
operate the lens A fig. 160 to press in the internal
catch B fig. 161, then pull the unit outwards;
turn the bulb holder C anti-clockwise, extract
bulb D and replace it;
refit the bulb holder C in the lens and turn it
clockwise;
refit the unit making sure that the internal catch B
clips into position.
fig. 158F0T0095
fig. 159F0T0096
fig. 160F0T0097
171
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

FOG LIGHTS
(for versions/markets, where provided)
IMPORTANT Contact Fiat Dealership to replace the
front fog lights.
REAR LIGHT CLUSTERS
The rear light clusters contain taillight, brake light,
direction indicator and reverse/rear fog light bulbs.
To access the light clusters, proceed as follows:
open the rear swing doors;
loosen the screws A fig. 162 so as to access the
light cluster B fig. 163;
remove the connector C fig. 163.
The bulbs are arranged inside the light cluster fig. 164
and fig. 165 as follows:
ABrake lights
BDirection indicators
CReverse lights
DTail lights/rear fog light
fig. 161F0T0098fig. 162F0T0099
172
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

Pull the 5 tabs E fig. 164 outwards to access the
bulbs.
fig. 163F0T0100
fig. 165F0T0102fig. 164F0T0101
173
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

THIRD BRAKE LIGHTS
Swing door versions
Contact Fiat Dealership to replace the third brake
lights fig. 166.
NUMBER PLATE LIGHTS
Proceed as follows to replace the bulbs A fig. 167:
operate the holding tabs at the points indicated by
the arrows, and remove the bulb holder;
turn the bulb holder B fig. 168 anticlockwise and
then remove the bulb C.
CHANGING AN INTERIOR BULB
For the type of bulb and corresponding power rating,
see the paragraph "Changing a bulb".
fig. 166F0T0103
fig. 167F0T0104
fig. 168F0T0105
174
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

FRONT CEILING LIGHT
Ceiling light with movable lens
To change the bulbs, proceed as follows:
extract the ceiling light A fig. 169 by operating in
the points shown by the arrows;
open the lid B fig. 170 as shown;
remove bulb C fig. 170 by releasing it from the
side contacts, then insert the new bulb and make
sure it is correctly clamped between these
contacts;
close the lid and secure the ceiling light into its
housing, making sure it locks properly into place.
Roof light with spot lights
(for versions/markets, where provided)
To change the bulbs, proceed as follows:
operate in the points shown by the arrows and
remove ceiling light A fig. 171;
open the protective lid B fig. 172;
replace the bulbs C releasing them from the side
contacts and making sure that the new bulbs are
correctly secured between the contacts;
re-close the lid B fig. 172 and secure light A
fig. 171 into its housing locking it properly.
fig. 169F0T0106
fig. 170F0T0458
fig. 171F0T0143
175
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

REAR CEILING LIGHT
Cargo Versions
To change the bulb, proceed as follows:
extract the ceiling light A fig. 173 by operating in
the points shown by the arrows;
open the lid B fig. 174 as shown;
remove bulb C fig. 174 by releasing it from the
side contacts, then insert the new bulb and make
sure it is correctly clamped between these
contacts;
close the lid B fig. 174 and secure the ceiling light
into its housing, making sure it locks properly into
place.
close the lid B and secure the ceiling light into its
housing, making sure it locks properly into place.
Combi Versions
To change the bulb, proceed as follows:
press button A fig. 175 and extract the removable
ceiling light B;
extract the ceiling light by operating in the points
shown by the arrows;
fig. 172F0T0144
fig. 173F0T0107fig. 174F0T0458
176
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

change the bulb C fig. 176 by releasing it from the
side contacts and making sure the new bulb is
correctly fastened between these contacts.REPLACING A FUSE
INTRODUCTION
Fuses protect the electrical system: they cut in (i.e.
they blow) in the event of a fault or improper action
on the system.
Check the state of the corresponding fuse when a
device does not work: the filament A fig. 177 should
be intact.
If it is not, replace the blown fuse with a new one of
the same amperage (same colour).
B intact fuse.
C fuse with damaged filament.
To change a fuse, use the tongs D located in the tool
bag or the Fix & Go container (for versions/markets,
where provided).
A
U
T
O
fig. 175F0T0108
A
U
T
O
fig. 176F0T0109fig. 177F0T0015
177
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX