2017 FIAT 500L key

buffeting occurs with the sunroof open, adjust the
sunroof opening to minimize the buffeting or open any
window.
Power Sun Blind
Pull the power sun blind switch and the blind will
move towards the rear part of the vehicle, until it is fully
open.
With the blind fully open pull the power sun blind
switch and the blind will move towards the front part of
the vehicle, until it is fully closed.
NOTE:During the automatic opening and closing
stages, if the power sun blind switch is pulled again it
will stop the blind movement.
POWER OUTLETS
Passenger Compartment Power Socket
The power outlet is located on the central tunnel, in
front of the gear selector, between the two cup holders.
It only operates with the ignition key at MAR/ON.
On models with optional smoker ’s kit,the cigar
lighter takes the place of the power socket (see Cigar
lighter paragraph). NOTE:
Do not connect devices with power higher than
180 W to the socket. Do not damage the socket by using
unsuitable adaptors.CIGAR LIGHTER — IF EQUIPPED
This is located on the central tunnel, next to the parking
brake lever. To activate the cigar lighter, push and
release the knob. After a few seconds the knob auto-
matically returns to its initial position, and the cigar
lighter is ready for use.
Passenger Compartment Power Socket
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119

Electronic Throttle Control (ETC) Warning Light
Red TelltaleLight What It Means
Electronic Throttle Control (ETC) Warning Light
This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a
problem is detected while the engine is running, the light will either stay on or flash de-
pending on the nature of the problem. Cycle the ignition key when the vehicle is safely and
completely stopped and the transmission is placed in the PARK position. The light should
turn off. If the light remains on with the engine running, your vehicle will usually be driv-
able; however, see an authorized dealer for service as soon as possible.
If the light continues to flash when the engine is running, immediate service is required and
you may experience reduced performance, an elevated/rough idle, or engine stall and your
vehicle may require towing. The light will come on when the ignition is first turned to ON/
RUN and remain on briefly as a bulb check. If the light does not come on during starting,
have the system checked by an authorized dealer.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 141

Engine Check/Malfunction Indicator Light (MIL)
Yellow TelltaleLight What It Means
Engine Check/Malfunction Indicator Light (MIL)
The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic
System called OBD II that monitors engine and automatic transmission control systems. The
light will illuminate when the ignition is in the ON/RUN position before engine start. If the
bulb does not come on when turning the key from OFF to ON/RUN, have the condition
checked promptly.
Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate
the light after engine start. The vehicle should be serviced if the light stays on through sev-
eral typical driving styles. In most situations, the vehicle will drive normally and will not
require towing.
When the engine is running, the MIL may flash to alert serious conditions that could lead to
immediate loss of power or severe catalytic converter damage. The vehicle should be ser-
viced as soon as possible if this occurs.
WARNING!
A malfunctioning catalytic converter, as referenced
above, can reach higher temperatures than in nor-
mal operating conditions. This can cause a fire if
(Continued)
WARNING!
(Continued)
you drive slowly or park over flammable sub-
stances such as dry plants, wood, cardboard, etc.
This could result in death or serious injury to the
driver, occupants or others.
146 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DISPLAY
Your vehicle may be equipped with an instrument
cluster display, which offers useful information to the
driver. With the ignition in the STOP/OFF position (and
the key removed, for vehicles with mechanical key),
opening/closing of a door will activate the display for
viewing, and display the total miles or kilometers in the
odometer. Your instrument cluster display is designed
to display important information about your vehicle’s
systems and features. Using a driver interactive display
located on the instrument panel, your instrument clus-
ter display can show you how systems are working and
give you warnings when they aren’t. The steering wheel
mounted controls allow you to scroll through and enter
the main menus and submenus. You can access the
specific information you want and make selections and
adjustments.
Instrument Cluster Display Control Buttons
The instrument cluster display control buttons are lo-
cated on the instrument panel below the radio.Push and release the
MENUbutton briefly to access the
menu and/or go to next screen or to confirm the
required menu option. Push and hold the MENU
button (approximately one second) to return to the
main screen.
Push and release the up
button to scroll upward
through the displayed menu and the related options
or to increase the displayed value.
Push and release the downbutton to scroll down-
ward through the displayed menu and the related
options or to decrease the value displayed.
NOTE: upand downbuttons activate differ-
ent functions according to the following situations:
• To scroll the menu options upwards or downwards.
• To increase or decrease values during settings.
NOTE: When opening one of the front doors, the
instrument cluster display will turn on the clock, the
external temperature and the miles or kilometers cov-
ered for a few seconds.
152 UNDERSTANDING YOUR INSTRUMENT PANEL

To make your choice, proceed as follows:
•Briefly push the MENUbutton.Initial page will be
displayed.
• Briefly push the MENUbutton again to display the
date andengine info options.
• Push the up
ordownbuttons to select the
information you wish to see on the main page of
the display.
• Briefly push the MENUbutton to go back to the
menu screen or hold the button down to go back to
the standard screen without saving.
When the key is turned to MAR/ON and the initial
check stage is over, the display will show the informa-
tion selected via the First Pagemenu function.
Audio Repetition (Repeat Audio Information)
With this function active, the instrument cluster display
shows information relevant to the sound system.
•Radio: tuned radio station frequency, automatic tun-
ing activation or AutoStore.
• CD audio, CD MP3: track number. To activate (On) or to deactivate (Off) the sound system
info displaying, proceed as follows:
1. Briefly push and release the
MENUbutton. Push and
release the up
ordownarrow button to
highlight See Radio and push and release the
MENU button.
2. Push and release the upordownarrow
button for setting.
3. Briefly push and release the MENUbutton to go
back to the menu screen, or push and hold the
MENU button (approximately one second) to go
back to the main screen without storing the settings.
If the radio has Uconnect, refer to the appropriate
“Uconnect Radio Supplement” for further information.
Audio Repetition Submenu Settings:
• Off
• On
• Return to MENU
162 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE:The “Scheduled Servicing Plan” includes car
maintenance at fixed intervals. This is displayed auto-
matically, with ignition key at MAR/ON, 1242 miles
(2000 km) before servicing or, where provided, 30 days
before servicing. It is also displayed each time the key is
turned to MAR/ON or every 124 miles (200 km). Below
this threshold, servicing indications are more frequent.
The display will be in miles or km according to the unit
of measurement set. When the next scheduled service is
approaching, the word “Service” will appear on the
display, followed by the number of miles/kilometers or
days left, when the key is turned to MAR/ON. Go to a
Fiat Dealership, where the Scheduled Servicing Plan
operations will be performed and the message will be
reset.
When the service interval is reached and for about 600
miles/1000 km or 30 days, a service due message is
displayed.
Airbag/Passenger Bag (Activation/Deactivation Of
Passenger Side Front Airbag And Side Bag For
Pelvis, Chest And Shoulder Protection)
This function allows the passenger airbag to be acti-
vated / deactivated. Proceed as follows:
1. Push the
MENUbutton and, after the message Bag
pass: Off (to deactivate) or Bag pass: On(to
activate) is displayed by pushing upand down
buttons, push the MENUbutton again.
2. A confirmation request message will appear on the display.
3. By pushing the upordown buttons select Ye s(to
confirm activation/deactivation) or No(to cancel).
4. Push the MENUbutton briefly; a message confirm-
ing the selection is displayed and you return to the
menu screen; hold down the button to return to the
standard screen without storing.
Daytime Running Lamps (DRL)
This function may be used to activate/deactivate the
Daytime Running Lamps.
Proceed as follows to switch this function on or off:
1. Briefly push and release the MENUbutton. Push and
release the up
ordownbutton to highlight
Daytime Running Lamps (DRL). Push and release
the MENU button to enter the DRL MENU.
166 UNDERSTANDING YOUR INSTRUMENT PANEL

Setting NameSelectable Options
Flash Headlights With Lock YesNo
NOTE: When this feature is selected, the exterior lights will flash when the doors are locked with the key fob.
Sound Horn With Remote Lock YesNo
Sound Horn With Remote Start YesNo
1st Press Of Key Fob Unlocks 1st Press Of Key Fob Unlocks Unlock All Doors On 1st Press
NOTE:
•When 1st Press Of Key Fob Unlocks is selected, only the driver’s door will unlock on the first press of the
key fob unlock button. When 1st Press Of Key Fob Unlocks is selected, you must press the key fob unlock
button twice to unlock the passenger’s doors. When Unlock All Doors On 1st Press is selected, all of the
doors will unlock on the first press of the key fob unlock button.
•If the vehicle is programmed 1st Press Of Key Fob Unlocks, all doors will unlock no matter which Passive
Entry equipped door handle is grasped. If 1st Press Of Key Fob Unlocks is programmed, only the driver ’s
door will unlock when the driver ’s door is grasped. With Passive Entry, if 1st Press Of Key Fob Unlocks is
programmed pressing the handle more than once will only result in the driver ’s door opening. If driver door
first is selected, once the driver door is opened, the interior door lock/unlock switch can be used to unlock
all doors (or use key fob). Passive Entry YesNo
NOTE: This feature allows you to lock and unlock the vehicles door(s) without having to press the key fob lock
or unlock buttons.
184 UNDERSTANDING YOUR INSTRUMENT PANEL

Setting NameSelectable Options
Memory Linked to Key Fob On/ Off — If Equipped Ye s
N o
NOTE:
This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting
the vehicle. To make your selection, press the “Memory Linked to Key Fob On/Off” button on the touchscreen,
then choose “Yes” or “No.” The button will highlight indicating that the setting has been selected. Press the
back arrow/X button on the touchscreen to return to the previous menu.
Auto Comfort Systems — If Equipped
After pressing the “Auto-On Comfort & Remote Start”
button on the touchscreen the following settings will be
available:
Setting Name Selectable Options
Horn With Remote Start YesNo
Auto-On Driver Heated/Ventilated
Seat & Steering Wheel With Vehicle Start — If Equipped On
Off
NOTE: When this feature is selected the driver’s heated seat and heated steering wheel will automatically turn
ON when temperatures are below 40° F (4.4° C). When temperatures are above 80° F (26.7° C), the driver
vented seat will turn ON. To make your selection, press the “Auto Heated Seats” button on the touchscreen,
then select either “Off,” “Remote Start” or “All Starts.” The button will highlight indicating that the setting has
been selected. Press the back arrow button on the touchscreen to return to the previous menu.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 185