2017 CITROEN RELAY display

12
EcO-drIVInG
Optimise the use of your gearbox
With a manual gearbox, move off gently
and change up without waiting. While
accelerating changing up early. If your
vehicle has the system, the gear efficiency
indicator invites you to engage the most
suitable gear; follow its instructions as
soon as it is displayed in the instrument
panel.
drive smoothly
Maintain a safe distance between vehicles,
use engine braking rather than the
brake pedal, and press the accelerator
progressively. These practices contribute
towards a reduction in fuel consumption
and CO
2 emissions and also helps reduce
the background traffic noise.
If your vehicle has cruise control, make
use of the system at speeds above 20 mph
(30 km/h) when the traffic is flowing well.
control the use of your electrical
equipment
Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents before
using the air conditioning.
Above 30 mph (50 km/h), close the
windows and leave the air vents open.
Remember to make use of equipment
that can help keep the temperature in the
passenger compartment down. Switch off the headlamps and front
foglamps when they are not needed for
safety.
Eco-driving is a range of everyday
practices that allow the motorist to optimise
their fuel consumption and CO
2 emissions.
Avoid running the engine before moving
off, particularly in winter; your vehicle will
warm up much faster while driving.
Disconnect your portable devices before
leaving the vehicle.Switch off the air conditioning, unless it
has automatic digital regulation, as soon
as the desired temperature is attained.
Switch off the demisting and defrosting
controls, if not automatic.
Switch off the heated seat as soon as
possible.
Motoring & the Environment

23
1. Speedometer (mph or km/h).
2.
Display screen.
3.


Fuel gauge.
4.


Coolant temperature.
5.


Rev counter (rpm or tr/min x 1000).
InStruMEnt PAnELS
Level 1 display screen
In the lower part:
-
T
ime,
-

Ambient temperature,
-


Miles
/ kilometres travelled,
-

T
rip computer (range, fuel
consumption...),
-

Headlamp beam height,
-


Programmable overspeed warning,
-


Cruise control or speed limiter
,
-

Gear ef
ficiency indicator,
-

Stop & Start.
In the upper part:
-


Date,
-


Service indicator
,
-

Alert messages,
-


System status messages,
-


V
ehicle configuration.
Level 1 instrument panel

/ display screen
2
rEAdY tO GO
Instruments and controls

24
Level 2 display screen
In the left-hand part:
-
T
ime,
-

Ambient temperature,
-


Alert or state indicators,
-


Cruise control or speed limiter
.
In the right-hand part:
-

Date,
-


Service indicator
,
-

T
rip computer (range, fuel
consumption...),
-

Alert messages,
-


Messages on the state of systems,
-


V
ehicle configuration,
-

Headlamp beam height,
-


Miles
/ kilometres travelled.
Level 2 instrument panel

/ display screen
Instruments and controls

31
Screendisplays indicates Solution - action
Temperature /
Ice the ice warning,
the temperature
flashing
accompanied by
a message in
the screen.weather conditions which could
result in ice on the road.
Be particularly vigilant and do not brake sharply.
"Safety - Driving safely".
Date
/ Timea setting: date,
time. a configuration via the "MODE"
menu.
"Technology on board
- Vehicle configuration" section.
Headlamp beam
height a headlamp
beam height
setting.a position from 0 to 3
depending on the load carried. Adjust using the buttons in the MODE control panel.
"Ease of use and comfort - Steering mounted controls"
section.
Service spanner a service
spanner which
remains on.a service will soon be due.
Refer to the list of checks in the manufacturer's service
schedule, then have the service carried out.
Stop & Start on.
engine going into STOP mode
after the vehicle stops. As soon as you want to move off, the warning lamp
goes off and the engine restarts automatically in
START


mode.
flashes for a few
seconds, then
goes off. STOP mode temporarily
unavailable.
Special cases for STOP mode.
"Ready to go
- Starting and stopping" section.
2
rEAdY tO GO
Instruments and controls

32
Screendisplays indicates Solution - action
Gear efficiency
indicator an up arrow. the possibility of changing up. "Ready to go - Gearbox and steering wheel" section.
Speed limiter on with "OFF".
the limiter selected is not
active.
Manual selection.
"Ease of use and comfort - Steering mounted controls"
section.
on. the limiter is on.
Instruments and controls

35under-inflation alert
The alert is given by the fixed
illumination of this warning lamp,
accompanied by an audible signal,
and depending on equipment, the
display of a message.
In the event of a problem on one of the
tyres, the symbol or the message appears,
according to equipment, to identify it.
-

Reduce speed, avoid sudden steering

movements or harsh brake applications.
-

Stop as soon as it is safe to do so.
-


In the event of a puncture, use the

temporary puncture repair kit or the
spare wheel (according to equipment).
-

In the event of under-inflation:
●


if you have a compressor
, the one
in the temporary puncture repair
kit for example, check the four tyre
pressures when cold,


or
●

if it is not possible to check the

tyre pressures at the time, drive
carefully at reduced speed and go
to the nearest CITROËN dealer or a
qualified workshop. The loss of pressure detected does
not always lead to visible deformation
of the tyre.
Do not rely on just a visual check.
The alert is maintained until the tyre or


tyres concerned is reinflated, repaired
or replaced.
Operating fault
The flashing and then fixed
illumination of this warning lamp
accompanied by the illumination
of the service warning lamp, and
depending on equipment, the display of a
message indicates a fault with the system.
In this case, monitoring of the tyre pressures
is not assured.
This alert is also displayed when one or
more wheels is not fitted with a sensor.
Go to a CITROËN dealer or a qualified
workshop

to have the system checked or,
following the repair of a puncture, to have
the original wheel, equipped with a sensor,
refitted.
2
rEAdY tO GO
Instruments and controls

36SErVIc E I nd I c AtO r Engine oil level
After a few seconds, the display returns to
its usual functions.
Engine oil condition
If in doubt, check the level with the dipstick. This 2nd warning lamp, coupled with
the 1st, comes on in the instrument
panel when the oil has not been
changed and the deterioration of
the oil has reached another threshold. If this
warning comes on at regular intervals, have the
oil changed as soon as possible. The warning lamp flashing and,
if your vehicle has the function,
a message displayed at every
engine start: the system has
detected deterioration of the engine oil.
Have the oil changed as soon as possible.
For 3.0 litre HDi engines, the engine
speed is restricted to 3 000 rpm, then
1 500 rpm until the oil change is done.
Have the engine oil changed to avoid
any risk of damage.
Servicing information
For a few seconds after the ignition is
switched on, the spanner symbolising service
information comes on: the screen informs you
when the next service is due, in accordance
with the servicing schedule indicated in
themanufacturer's service schedule. Depending on the engine, the engine oil
level then appears, graduated from 1 (Min)
to 5 (Max).
If no graduation is displayed, the oil level is
too low; you must top-up to avoid damaging
the engine.
For the oil level reading to be accurate, the
vehicle must be parked on level ground, with
the engine off for more than 30 minutes.
Refer to the "Checks - Levels and
checks" section.
This information is determined in relation
to the distance travelled since the previous
service.
Instruments and controls

37
Refer to the "Technology on board -
Vehicle configuration" section.
reminder of servicing information
At any time, to access the service indicator,
press briefly on the MOd E button.
Use the up/down arrows to see the
scheduling and engine oil wear information.
Pressing the MO
d E button again allows you
to return to the various display menus.
A long press returns you to the main menu.
Menu...
c

hoose...
Allows you to...
11
Service Service
(miles/
km before
service)
Display the
distance
remaining
before the
next service.
Oil (miles/
km
before oil
change) Display
the miles/
kilometres to
the next oil
change.
Refer to the list of checks in the
manufacturer's service schedule which
was given to you on handover of the
vehicle.
resetting the servicing information
The continuous flashing of the indicator is
stopped by a qualified workshop using a
diagnostic tool, after each service.
If you have carried out the service on your
vehicle yourself, you can reset the service
indicator as follows:
F
insert the ignition key into the switch,
F
turn it to the

MA r position,
F
simultaneously press the brake and


accelerator pedals for more than
15
seconds.
2
rEAdY tO GO
Instruments and controls