2017 CITROEN DISPATCH SPACETOURER DAG belt

98
Spacetourer-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Folding the backrest to the
table position
F Put the head restraints into the low position.
F

T

o raise a head restraint, pull it up until it
engages in its notches.
F

T

o remove the head restraint, press the
lug

A and pull the head restraint upward.
F

T

o put it back in place, engage the head
restraint rods in the apertures keeping
them in line with the seat backrest.
F

T

o lower it, press on the lug A and on the
head restraint at the same time.Angled head restraints
For more information on the Seat belts ,
refer to the corresponding section. F

F
rom the front, raise the handle to release
the backrest.
F
F
rom the rear, lower the lever to release
the backrest.
Fixed rear seat and bench seatThe different levels of equipment and adjustments described hereafter vary according to the
version and the configuration of your vehicle.
The seat has a backrest that may be fixed or
folding (table position).
The bench seat has a one-piece backrest that
may be fixed or foldable (table position).
Ease of use and comfort

101
Spacetourer-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Head restraints
F To raise a head restraint, pull it up until it engages in its notch.
F

T
o remove it, press the lug A and pull the
head restraint up.
F

T
o refit it, engage the head restraint rods in
the apertures keeping them in line with the
seat backrest.
F

T
o lower it, press on the lug A and on the
head restraint at the same time.
Rear seat and bench seat on rails
The different equipment and adjustments
described hereafter vary according to the
version and configuration of your vehicle.
For more information on the Seat belts ,
refer to the corresponding section. F

T
o recline the backrest, raise the control
(from the rear, lower the lever).
F

R
elease the control when the desired
position is obtained.
Reclining the backrest
The reclining backrest can be adjusted to
several positions.
The individual seat is always on the right and
the bench seat on the left (facing for ward).
The bench seat has two independent
backrests.
3
Ease of use and comfort

105
Spacetourer-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Individual seat(s) on rails
The different equipment and adjustments
described hereafter vary according to the
version and configuration of your vehicle.F

T
o raise a head restraint, pull it up until it
engages in its notch.
F

T
o remove it press the lug A and pull the
head restraint up.
F

T
o refit it, engage the head restraint rods in
the apertures keping them in line with the
seat backrest.
F

T
o lower it, press on the lug A and on the
head restraint at the same time.
Head restraints
The armrest has notches.
F P ull the armrest fully up.
F

L
ower it fully down.
F

R
aise the armrest to the desired position.
Ar mrest(s)
It can be placed forward facing or
rearward facing.
The individual seat is fitted with a three-point
inertia reel seat belt.
For more information on the Seat belts ,
refer to the corresponding section.
3
Ease of use and comfort

109
Spacetourer-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Precautions for the
seats and bench
seats
Following the various handling operations:
- d o not remove a head restraint without
storing it and fixing it to a support,
-

c
heck that the seat belts are always
accessible to the passenger and easy to
fasten,
-

a p
assenger must not take their seat
without adjusting the seat's head restraint
correctly and adjusting and fastening the
seat belt.
Loading luggage or objects
behind the row 3 seat and
bench seat
If you want to load luggage onto the backrests
in row 3 while in the table position, the
backrests in row 2 must also be in the table
position.
Labels
When driving, carrying a passenger is
prohibited:
-

i
n row 3 if the backrest in front (row 2) is in
the table position.
-

i
n row 3 if the seat /bench in front (row 2) is
in the fully folded position.
-

i
n rows 2 and 3, in the outer right seat, if
the bench is in the fully folded position,
-

o
n the centre seat if the outer right seat is
in the fully folded position.
3
Ease of use and comfort

164
Spacetourer-VP_en_Chap05_securite_ed01-2016
Seat belts
Front seat beltsFastening
Unfastening
F Press the red button on the buckle.
F G uide the seat belt as it reels in.
The front seat belts are fitted with a
pretensioning and force limiting system.
This system improves safety in the front
seats in the event of a front or side impact.
Depending on the severity of the impact, the
pretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The force limiter reduces the pressure of the
seat belt on the chest of the occupant, so
improving their protection.
Height adjustment
The upper part of the diagonal strap
should lie across the shoulder.
F

T

o lower the attachment point, while
moving control A downwards, slide the
assembly down to the desired position.
F

T

o raise the attachment point, slide the
assembly up to the desired position.
F

P

ull the strap, then insert the tongue in the
buckle.
F

C

heck that the seat belt is fastened
correctly by pulling the strap.
Safety

165
Spacetourer-VP_en_Chap05_securite_ed01-2016
2 seat front bench seat
If your vehicle is fitted with a 3 -seat bench seat
(one piece or 1/3 - 2/3 split), these are fitted
with three-point seat belts and inertia reels on
the outer seats.
And the centre seat has its own guide and reel,
built into the seat backrest.
The seat belt reels for the outer seats in row 2
have force limiters.
The seats in row 3 have three-point seat belts
with inertia reels.
If your vehicle is fitted with a front bench seat,
ensure that each belt is used with its correct
buckle.
Do not interchange the driver's seat belt or
buckle with the centre seat belt or buckle. For rows 2 and 3, fit each seat belt to its
correct buckle.
Do not interchange the belts or buckles
for the outer seats with the belt or
buckle for the centre seat.
When folding the outer seats or placing
a backrest in the table position, avoid
trapping the belt for the centre seat.
After folding a rear seat or bench seat,
ensure that the seat belt has reeled
in correctly and the buckle is ready to
receive the belt tongue.
When handling the outer seats
(removing or refitting) or for access to
row 3, avoid trapping the centre belt.
Rear seat belts
5
Safety

166
Spacetourer-VP_en_Chap05_securite_ed01-2016
Seat belt warning lamps
If your vehicle has individual front seats:
1. Driver's seat belt not fastened / unfastened
warning lamp in the instrument panel.
2.
F

ront passenger seat belt not fastened /
unfastened warning lamp.
From about 12 mph (20 km/h) and for
two minutes, the warning lamps(s)
flash accompanied by an audible
signal. Beyond these two minutes,
the warning lamps remain on if the
driver or front passenger do not
fasten their seat belt(s).
On switching on the ignition, a warning lamp comes
on in the instrument panel if the corresponding seat
belt is not fastened or is unfastened.
If your vehicle has a 2-seat bench front seat:
A. O uter left (driver) seat belt not fastened /
unfastened warning lamp.
B.
C

entre and/or outer seat belt not fastened
warning lamp.
When the ignition is switched on, the warning
lamp A comes on if the driver's seat belt is not
fastened or unfastened.
The warning lamp B comes on if the centre
and/or an outer seat belt is unfastened.
If your vehicle is fitted with individual seats,
they have three-point seat belts with their
guides and belt reels built into the backrests.
Safety

167
Spacetourer-VP_en_Chap05_securite_ed01-2016
Advice
In the event of an impact
Depending on the nature and
seriousness of the impact, the
pretensioning device may be deployed
before and independently of the airbags.
Deployment of the pretensioners is
accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp
comes
on.
Following an impact, have the seat belts
system checked, and if necessary replaced,
by a CITROËN dealer or a qualified
workshop.
In order to be effective, a seat belt must:
-

b

e tightened as close to the body as
possible,
-

b

e pulled in front of you with a smooth
movement, checking that it does not
twist,
-

b

e used to restrain only one person,
-

n

ot bear any trace of cuts or fraying,
-

n

ot be converted or modified to avoid
affecting its performance.
In accordance with current safety
regulations, for all repairs on your vehicle's
seat belts, go to a qualified workshop with
the skills and equipment needed, which a
CITROËN dealer is able to provide.
Have your seat belts checked regularly by
a CITROËN dealer or a qualified workshop,
particularly if the straps show signs of
damage.
Clean the seat belt straps with soapy
water or a textile cleaning product, sold by
CITROËN dealers.
After folding or moving a seat or rear bench
seat, ensure that the seat belt is positioned
and reeled in correctly.
Recommendations for children
Use a suitable child seat if the passenger is
less than 12 years old or shorter than one
and a half metres.
Never use the same seat belt to secure more
than one person.
Never allow a child to travel on your lap.
For more information on Child seats , refer
to the corresponding section.
The driver must ensure that passengers use
the seat belts correctly and that they are all
fastened before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do not interchange the seat belt buckles as
they will not fulfill their role fully.
The seat belts are fitted with an inertia reel
permitting automatic adjustment of the
length of the strap to your size. The seat belt
is stowed automatically when not in use.
Before and after use, ensure that the seat
belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the pelvis.
The upper part must be positioned in the
hollow of the shoulder.
The inertia reels are fitted with an automatic
locking device which comes into operation in
the event of a collision, emergency braking
or if the vehicle rolls over. You can release
the device by pulling the strap firmly and
then releasing it so that it reels in slightly.
5
Safety