2017 CITROEN C-ZERO tow

126
Changing a bulb
1. Direction indicators (W21W - 21 W).
2. S idelamps (W5W - 5 W).
3.
M

ain beam headlamps (HB3 - 60 W).
4.
D

ipped beam headlamps (H11 - 55 W).
The headlamps have polycarbonate
lenses with a protective coating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F

u

se a sponge and soapy water or a
pH neutral product,
F

w

hen using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals.
Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F

D

o not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (UV) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
Front lamps
5. Front foglamps (H8 - 35 W).
6. D aytime running lamps
(P13W - 13 W).
In the event of a breakdown

128
F Slacken fixing screw D, while holding the
bumper away.
F

S
lacken fixing screw E . F
P ull the lamp towards you, and disengage
the tab F to remove it completely.
In the event of a breakdown

131
1. Brake lamps / Sidelamps
(21 W / 15 W or LEDs).
2.
D

irection indicators (WY21W - 21 W).
3.
R

eversing lamps (W21W - 21 W).
Rear lamps
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specification and
c o l o u r.
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
Changing integrated direction
indicator side repeater bulbs
(WY5W - 5
W)
F Push the repeater towards the rear and disengage it.
F

T
urn the bulb holder to the left and pull
it
out.
F

P
ull the bulb out and change it.
To reassemble, carry out these operations in
reverse order.
Access to bulbs
F Remove the two screws.
F D isengage the lamp unit by pulling it
towards you.
8
In the event of a breakdown

134
Changing a fuse
The extraction tweezer is fitted to the back of
the fusebox cover in the dashboard (right-hand
side).
For access:
F
U
nclip the cover and remove it completely
by pulling it towards you.
F

R
emove the tweezer.
Access to tools
Before changing a fuse, the cause of the failure
must be identified and rectified.
F
C
heck that the ignition switch is in the
" LOCK " position.
F

I
dentify the failed fuse by checking the
condition of its filament.
Changing a fuse
Good Failed
F

U

se the special tweezer to extract the fuse
from its location.
F

A

lways replace the failed fuse with a fuse
of the same rating.
F

C

heck that the number marked on the box,
the rating marked on the top of the fuse
and the tables below all agree. CITROËN will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying the malfunctions
resulting from the installation of
accessories not supplied and not
recommended by CITROËN and
not installed in accordance with its
instructions, in particular when the
consumption of all of the additional
equipment connected exceeds
10
mil

liamperes.
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories in your
vehicle, contact a CITROËN dealer or a
qualified workshop.
In the event of a breakdown

136
Fuse N°Rating Functions
14 15 ARear wiper.
15 7. 5 AInstrument panel.
16 7. 5 AHeating.
17 20 AHeated seat.
18 10 AOption.
19 7. 5 ADoor mirror heating.
20 20 AWindscreen wiper.
21 7. 5 AAirbags.
22 30 AHeated rear screen.
23 30 AHeating.
24 -Not used.
25 10 ARadio.
26 15 APassenger compartment fuse.
To gain access to it:
F

U

nclip the cover and remove it completely
by pulling it towards you.
In the event of a breakdown

138
Access to the fuses
F Open the bonnet.
F U nclip the cover and remove it completely
by pulling towards you.
F

C
hange the fuse.
F

W
hen you have finished, close the cover
carefully to ensure sealing of the fusebox. Fuse N°
Rating Functions
11 10 AOn-board charger.
12 10 ADirection indicators.
13 10 AHorn.
14 10 ADaytime running lamps.
15 15 ABattery fan.
16 10 AAir conditioning compressor.
17 20 ARight-hand dipped beam.
18 20 ALeft-hand dipped beam, headlamp adjustment.
19 10 ARight-hand main beam.
20 10 ALeft-hand main beam.
In the event of a breakdown

139
Towing the vehicleProcedure for having your vehicle towed using fixed mechanical equipment.
Towing your vehicle
The towing eye is welded to the body below the
front bumper.
F
I
nstall the towing bar.
F

S
tart your vehicle ("Ready" lamp on).
F

P
ut the drive selector in position N .
F

R
elease the parking brake.
F

S
witch on the hazard warning lamps on
your vehicle.
F

H
ave your vehicle towed for no more than
20 miles (30 km) without exceeding a
speed of 20 mph (30 km/h) .When towing the vehicle with the four
wheels on the ground, always use a
towing bar.
When towing with only two wheels on
the ground, use professional lifting
equipment.
Failure to follow these instructions may
cause damage to braking components
and the electric motor.
Towing another vehicle
Your vehicle cannot be used in any
circumstances to tow another vehicle.
8
In the event of a breakdown

141
Electric motorY51
Main battery Lithium-Ion
Model type code: 1 N ZK Y Z
Unladen weight 1 065
Kerb weight 1 140
Gross vehicle weight (GV W) 1 450
Gross train weight (GTW) 1 450
Maximum load on the roof (including the roof bars) 43
Your vehicle cannot be fitted with a towbar. It cannot tow a trailer.
Weights (in kg)
9
Technical data