2017 Citroen BERLINGO Chapter 8

166
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Range indicators
Rules on the display of alertsFor more information on the
displays and warning lamps, refer
to chapter 3, "Instruments and
controls"
  section. Range greater than 1 500 miles
(2 400 km)
No
  information   displayed.
Once   the   1   500   miles   (2   400   km)  
threshold is reached, the UREA


warning lamp comes on temporarily
and the remaining range message is
displayed.
The alert is repeated every 200 miles
(300
  km)   until   the   next   threshold   is  
reached.
Every time the ignition is switched
on, the alert is given, together with an
audible

  signal.
Remaining range less than
1
500 miles (2 400 km) and greater
than 350 miles (600 km)
Driving range
With
  the   touch   screen   tablet:
If the range is greater than 3 100 miles
(5
  000   km),   a   range   value   is   not   given.
Press this button to display
the
  information.
-

select the "Driving
assistance" menu,
-


select "Diagnostic",
-

 
select
  CHECK.
Different levels of alert are triggered
according to the remaining driving
range threshold
You will be informed as each mileage
threshold is reached and the alerts will
change
  from   temporary   to   permanent.
-

The 1st is triggered at a remaining
driving range of 1 500 miles
(2
 
400
  km).
-

The 2nd is triggered at a remaining
driving range of 350 miles
(600
 
km).
-

Up to 0 miles, at which point it will
be impossible to restart the engine
after

 
a
 
stop.
AdBlue®

177
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
FITTING THE WHEEL
TRIM
The tyre valve must be centred in the
wheel
  trim   cut-out.
This
  position   is   essential   for   fitting   the  
wheel

  trim   correctly   on   the   steel   wheel.  
(If

the valve is not correctly aligned with
the cut-out, the anti-rotation system
will be in contact with the heads of the
wheel
  bolts   and   risks   being   damaged  
if

  the   user   persists   in   fitting   the   wheel  
trim

  in   this   incorrect   position). -

Ensure that all of the clips are
engaged except the last one
(opposite

  the   valve   hole).
-
 
Strike
  the   wheel   trim   with   the   palm  
of your hand, opposite the valve
in

  the   area   of   the   last   fixing   clip  
(always

  in   the   direction   of   clipping).
-

Ensure that the outer edge of
the wheel trim is not deformed or
pushed

  into   the   wheel:
●
 
Correct
position for the edge of
the
  wheel   trim.
●
 
Incorrect
position for the edge of
the
  wheel   trim.
Refer to the "Instruments and
controls" section of chapter 3,
"Tyre
 
under-inflation
 
detection"
 
part, for recommendations after
changing

 
a
 
wheel
 
fitted
 
with
 
a
 
tyre
 
under-inflation

 
detection
 
sensor.
Refer
 
to
 
the
 
"Identification
 
markings"

 
section
 
of
 
chapter
 
9
 
to
 
locate

 
the
 
tyre
 
label.
6. Refitting the repaired wheel
The wheel is refitted as described in step   5,   not   forgetting   to   refit   the   wheel  
trim.
QUICK HELP
8
Changing a wheel

185
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
After changing the rear direction
indicator bulb, the reinitialisation time is
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-

Remove the faulty bulb by
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-

with tailgate, pull the lamp unit
towards the centre of the vehicle,
-


with hinged doors, pull the lamp
unit

  towards   you.
For more information on bulbs, refer to
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B, PY21W - 21W (amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the other lamps
and their edges to avoid damaging
their
 
coating
 
and
 
seals. Chapter 9, "Changing a wheel"
section.
-

Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-

Holding the lamp, disconnect the
electrical

  connector.
QUICK HELP
8
Changing a bulb

 197
Berlingo2VP_en_Chap09_Caract-technique_ed02-2016Berlingo2VP_en_Chap09_Caract-technique_ed02-2016
ENGINE CHARACTERISTICS
The engine characteristics (capacity,
maximum power, maximum power
speed, fuel, CO
2 emissions...) for your vehicle are given in the registration
certificate.
These characteristics correspond
to the values type-approved
on a test bed, under conditions
defined
 
in
 
European   legislation  
(Directive 1999/99/EC).
For more information, refer to the
manufacturer's website or sales
brochure

 
for
 
the
  model.   Contact  
a

 
CITROËN
 
dealer   or   a   qualified  
workshop.
WEIGHTS AND TOWED LOADS
These values, expressed in kg, can be found on the manufacturer's VIN plate
or
  label.
The maximum weights and towed
loads for your vehicle can be found on
the
  vehicle's   registration   certificate.
The
  kerb   weight   is   equal   to   the   weight  
without

  load   +   driver   (75   kg)   +   fuel   tank  
filled

  to   90%.
The GTW and towed load values
indicated are valid up to a maximum
altitude
  of   1000   metres.  
The
  value   of  
the towed load mentioned must be
reduced by 10 % for each additional
1000

  metres.
With
  load   transfer,   the   braked   trailer  
weight can be increased, on condition
that the equivalent of this load is
removed from the vehicle so that the
GTW

  is   not   exceeded. High ambient temperatures
may result in a reduction in the
performance of the vehicle in
order
  to   protect   the   engine.   When   the  
ambient temperature is higher than
37 °C,

  limit   the   towed   weight.
Towing with a lightly loaded
vehicle can adversely affect road
holding.
Towing
  a   trailer   increases   braking  
distances.
When towing, the maximum permitted
speed is reduced (comply with the
legislation

  in   force   in   the   country).
The recommended nose weight is
the downward force on the towball
(removable
  with   or   without   tools).
GVW: gross vehicle weight, the
maximum
  authorised   weight.
GTW: gross train weight, the maximum
weight
  for   vehicle   plus   trailer.
The location of the manufacturer's
plate is given in chapter 9,
"Identification
  markings"   section.
In each country, it is imperative that
the maximum towed loads authorised
by local legislation are complied
with.
 
T
o   find   out   your   vehicle's   towing  
capacities and its gross train weight,
consult

  a   CITROËN   dealer.
TECHNICAL DATA
9
Weights

201
Berlingo2VP_en_Chap09_Caract-technique_ed02-2016Berlingo2VP_en_Chap09_Caract-technique_ed02-2016
IDENTIFICATION MARKINGS
A. Manufacturer's plate.C. Tyres and paint colour code.
The label C,
  on   the   front   door   gives:
-
the wheel and tyre sizes,
-

the tyre pressures, laden and
unladen,
-

the tyre pressure of the spare
wheel,
-
 
the
  paint   colour   code.
The   tyre   pressures   should   be   checked  
when

  cold,   at   least   once   a   month.
B. Serial number.
This is engraved on the front right
wheelarch.
If
  your   vehicle   is   fitted   with   the
 system,

  refer   to   the   "Under-inflation
 detection"

  section   in   Chapter   3.
TECHNICAL DATA
9
Identification markings