2017 Citroen BERLINGO replace

76
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
DEMISTING AND DEFROSTING
G
OOD PRACTICE
V

ents
"Leave them open"
For optimum distribution and diffusion
of hot or cool air in the passenger
compartment,
  there   are   adjustable  
central and side vents which can
be directed sideways (right or left)
or

  vertically   (up   or   down).   For   your  
comfort while driving, do not close
them

  and   direct   the   flow   of   air   towards  
the

  windows   instead.
Air vents in the footwells and directed
towards the windscreen complete the
equipment.
Do
  not   block   the   vents   located   at   the  
windscreen or the air extractor located
in

  the   boot.
Dust filter, odour filter
(activated carbon)
This filter traps certain dust and limits odours.
Ensure   that   this   filter   is   in   good  
condition

  and   have   all   of   the   filter  
elements

  replaced   regularly.
Refer
  to   the   "Checks"   section   of  
chapter

  7.
Air conditioning
In all seasons, the air conditioning
should only be used with the
windows  closed.   However,   if   the  
interior temperature remains high
after

  a   prolonged   period   parked   in  
the

  sun,   first   ventilate   the   passenger  
compartment

  for   a   few   minutes.
Use the AUTO mode as much as
possible as it permits optimised
control
  of   all   of   the   functions:   air   flow,  
passenger compartment comfort
temperature, air distribution, air
intake

  mode   or   air   recirculation   in   the  
passenger

  compartment.
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to
  keep   it   in   good   working   order.
If the system does not produce cold air,
do not use it and contact a CITROËN
dealer
  or   a   qualified   workshop.
Automatic mode: visibility
programme
The comfort programme (AUTO) may
not
 
be
 
sufficient
 
to
 
quickly
 
demist
 
or
 
defrost the windows (humidity

, several
passengers,
 
ice).
In this case, select the visibility
programme.
 
The

 
visibility
 
programme
 
indicator

 
comes
 
on.
It activates the air conditioning, the air
flow
 
and
 
provides
 
optimum
 
distribution
 
of the ventilation to the windscreen and
side

 
windows.
It
 
deactivates
 
the
 
air
 
recirculation. It is normal that the condensation
created by the air conditioning system
results
  in   a   flow   of   water   which   may  
form a puddle under the vehicle when
parked.
Ventilation

85
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Head restraint
This is of the "comma" shape type.
High   position:   press   the   tab,   lift   and  
raise

  the   head   restraint.
Low
  position:   push   the   tab   and   press  
the

  top   of   the   head   restraint   to   lower   it.
To
  remove   the   head   restraint:   place   it   in
 the

  high   position,   lift   it,   then   remove   it.
Store it inside the vehicle, securing it
firmly.
To
  install   the   head   restraint:   engage  
the rods of the head restraint in the
holes

  keeping   it   in   line   with   the   seat  
back.
Each seat can be removed and must
be

 
replaced
 
in
 
the
 
specified
 
position,
 
indicated

 
by
 
a
 
symbol
 
on
 
its
 
label.
The seats of row 2 and row 3 are
independent
 
and
 
adjustable.
REAR SEATS (7 SEAT VERSION)
EASE OF USE and COMFORT
4
Seats

99
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
SCENTED AIR FRESHENER
The scented air freshener diffuses
a fragrance in the passenger
compartment from the roof console
vents.
Adjusting the flow
Turn the chromed button to adjust the diffusion:
-

to the left to decrease,
-

 
to
  the   right   to   increase.
To stop the diffusion, turn the chromed
button
  fully   to   the   left.
Removing the scented air
freshener
- Press the button down while turning
it a quarter of a turn to the left to
the  stop.
-

Remove the scented air freshener
from

  the   roof   console.
-
 
Replace
  the   cartridge.
EASE OF USE and COMFORT
4
Practical information

122
Berlingo2VP_en_Chap05_Securite_ed02-2016
ACTIVE CITY BRAKE
Active City Brake is a driving assistance system that aims to avoid
a frontal collision or reduce the speed
of an impact if the driver does not
react
  sufficiently   (inadequate   brake  
application).
This system is designed to
improve

  driving   safety.
It remains the driver's responsibility to
continuously monitor the state of the
traffic
  and   to   assess   the   distances   and  
relative

  speeds   of   other   vehicles.
Active
  City   Brake   can   in   no  
circumstances replace the need for
vigilance

  on   the   part   of   the   driver. Never
  look   at   the   laser   sensor  
through an optical instrument
(magnifying

  glass,   microscope...)  
at a distance of less than
10 centimetres:

  risk   of   eye   injury.Principle
Using a laser sensor located at the top
of the windscreen, this system detects
a vehicle running in the same direction
or  stationary   ahead   of   your   vehicle.
When
  necessary,   the   vehicle's   braking  
system is operated automatically
to avoid a collision with the vehicle
ahead.
Automatic

  braking   occurs   later  
than if done by the driver

, so as
to intervene only when there is a
high
  risk   of   collision.
Conditions for activation
Active City Brake only operates if the following  conditions   are   met:
●
 
ignition
  on,
●
 
the
  vehicle   is   in   a   forward   gear,
●
 
speed
  is   between   about   3   and  
18 mph

  (5   and   30   km/h),
●
 
the
  braking   assistance   systems  
(ABS,

  EBFD,   emergency   braking  
assistance) are not faulty

,
●
 
the
  trajectory   control   systems  
(ASR, DSC) are not deactivated
or

faulty,
●
 
the
  vehicle   is   not   in   a   tight   corner,
●
 
the
  system   has   not   been   triggered  
during

  the   previous   10   seconds.
Driving safely

125
Berlingo2VP_en_Chap05_Securite_ed02-2016
Driving safely
Operating faults
Sensor fault
The operation of the laser sensor may
suffer interference from accumulations
of  dirt   or   misting   of   the   windscreen.  
In this case you are warned by the
display

  of   a   message.
Use the windscreen demisting
and regularly clean the area of the
windscreen
  in   front   of   the   sensor.
Do
  not   stick   or   otherwise   fix   any  
object

  on   the   windscreen   in   front  
of

  the   sensor. System fault
In the event of a malfunction of the
system, you are warned by an audible
signal and the display of the message
"Automatic braking system fault".
Have
  the   system   checked   by   a  
CITROËN

  dealer   or   a   qualified  
workshop.In the event of an impact to
the windscreen at the sensor

,
deactivate the system and contact
a
  CITROËN   dealer   or   a   qualified  
workshop 

to  
have
 
your
 
windscreen
 
replaced.
Never

  try   to   remove,   adjust   or   test  
the

  sensor.
Only a CITROËN dealer or a
qualified
  workshop   is   able   to   work  
on

  the   system.
When towing a trailer or when the
vehicle is being towed, the system
must
  be   deactivated.
SAFETY
5

158
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When the engine is warm, the
temperature of the coolant is controlled
by
  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has dropped, remove the cap and top
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this indicates a fault which must be
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes as soon as possible, when
traffic
  conditions   permit   (until   the  
message disappears and the service
warning

  lamp   goes   off).
During regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating may be heard under the
dashboard.
If the message is still displayed and
if the service warning lamp remains
on, contact a CITROËN dealer or a
qualified

  workshop.
Topping up
The level must be between the MIN
and
 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For optimum cleaning and to avoid
freezing,
  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This additive must be topped up by
a  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
Avoid prolonged contact of used oil
with  the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITROËN dealer (France) or
an

  authorised   waste   disposal   site.
The minimum level of this additive
is indicated by lighting of the service
warning lamp, accompanied by an
audible signal and a message in the
screen.
When this occurs with the engine
running it is due to the start of
saturation
 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

159
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
CHECKS
Carbon filter and passenger compartment filterParticle filter (Diesel)
Maintenance of the particle filter must be  carried   out   by   a   CITROËN   dealer.
On acceleration after the vehicle has
been running for a prolonged period
at very low speed or at idle, you may,
in exceptional circumstances, notice
the emission of water vapour at the
exhaust.
 
This
  water   vapour   does   not  
have any adverse ef

fect on vehicle
handling
  or   the   environment.
Battery
At the start of summer or winter, have
your  battery   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Brake pads
Brake pad wear depends on the style of driving, in particular for vehicles
which are used in town, over short
distances.
  It   may   be   necessary   to  
check

  the   thickness   of   the   pads,   even  
between

  services.
Unless
  there   is   a   leak   on   the   circuit,   a  
drop

  in   the   brake   fluid   level   indicates  
that

  the   brake   pads   are   worn.
Brake disc / drum wear
For information on checking the brake disc  /   drum   wear,   contact   a   CITROËN  
dealer

.
Parking brake
Where the parking brake travel is too great or there is a reduction in the
performance
  of   the   system,   the   parking
 brake

  should   be   adjusted,   even   between
 services.
Have

  the   system   checked   by   a   CITROËN
 dealer

  or   a   qualified   workshop.
Oil filter
Change the filter regularly in accordance with the manufacturer's
servicing  schedule.
An
 
access
 
flap
 
allows
 
replacement
 
of
 
the

 
filters.
The
 
carbon
 
filter
 
permits
 
continuous
 
and

 
effective
 
filtering
 
of
 
dust.
If
 
the
 
passenger
 
compartment
 
filter
 
becomes

 
blocked,
 
this
 
may
 
reduce
 
the
 performance of the air conditioning
system and generate unpleasant
odours.
W
e recommend the use of a combined
passenger
 
compartment
 
filter.
 
By
 
means of its second special active
filter

,
 
it
 
contributes
 
to
 
the
 
purification
 
of the air breathed by the occupants
and the cleanness of the passenger
compartment (reduction of allergic
symptoms, unpleasant odours and
greasy

 
deposits).
Refer to theservicing and warranty
booklet
 
for
 
the
 
replacement
 
interval
 
for
 
these

 
components. Depending on the environment (dusty
atmosphere...)
  and   the   use   of   the  
vehicle

  (urban   driving...),   change   them  
twice

  as   often   if   necessary.
CHECKS
7
Checks

172
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
The temporary tyre repair kit consists of a compressor and a bottle
(containing  a   sealant).
Using the kit
- Tick  the   deflated   wheel   on   the  speed
  limitation   sticker   then   affix  
the

  sticker   to   the   vehicle's   steering  
wheel to remind you that a wheel is
in

  temporary   use.
-

Clip the bottle
1 on the
compressor
2.
-

Connect the bottle
1 to the valve of
the
  tyre   to   be   repaired.
-
 
T
ake   care   to   unwind   the  
compressor pipe before connecting
it

  to   the   bottle.
-

Connect the power lead to one of
the

  vehicle's   12V   sockets.
-

Switch on the compressor by
pressing button

A until the tyre
pressure
  reaches   2.0   bars.   If   this  
pressure cannot be reached, the
tyre

  cannot   be   repaired.
-
 
Remove
  and   store   the   compressor.
-

Drive immediately
, for a few miles
(kilometres),
  at   reduced   speed,   to  
fill

  the   puncture.
-
 
Adjust
  the   pressure   using   the  
compressor in accordance with the
recommendation for the vehicle and
check

  that   the   leak   is   filled   correctly  
(no

  further   loss   of   pressure).
-

Drive at reduced speed (50
mph
[80
  km/h]).  
The
  tyre   must   be  
examined and repaired by a
specialist

  as   soon   as   possible.After use, the bottle can be stored in
a
  plastic   bag,   supplied   in   the   kit,   to  avoid staining your vehicle with traces
of
  fluid.
Warning:
  the   sealant   product   is  
harmful if swallowed and causes
irritation

  to   the   eyes.
Keep
  it   out   of   reach   of   children.
After use, do not discard the bottle into
the
  environment,   take   it   to   a   CITROËN  
dealer or to an specialised waste
disposal

  site.
Replacement bottles of sealant are
available
  from   CITROËN   dealers.
TEMPORARY PUNCTURE
REP

AIR KIT
The kit is located in one of the two storage compartments located
under
  the   front   seats.
Vehicles supplied with a temporary
puncture
  repair   kit   do   not   have   a   spare  
wheel

  or   tooling   (jack,   wheelbrace, ...).
Changing a wheel