2017 Citroen BERLINGO MULTISPACE RHD engine

32
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
WARNING LAMPS
Warning lamp is indicatesSolution - action
STOP on, associated
with another
warning
lamp and
accompanied
by a message
in
  the   screen.major
  faults   linked   with  
the

  "Brake   fluid   level",  
"Engine oil pressure and
temperature", "Coolant
temperature", "Electronic
brake

  force   distribution"   and  
"Power steering" warning
lamps.Y

ou must stop as soon as it is safe to do
so. Park and switch off the ignition. Have it
checked by a CITROËN dealer or a qualified
workshop.
Parking
brake
/
Brake fluid
level
/ EBFDon.
that the
 parking  brake  is  applied or
  has   not   been   released   fully.Releasing the parking brake switches off the warning  lamp.
on. low
 
brake
 
fluid
 
level. Top   up   using   a   fluid   recommended   by   CITROËN.
remaining on even
though the level
is correct and
associated with the
ABS
 
warning
 
lamp.
a fault with the electronic
brake  force   distribution. You must stop as soon as it is safe to do so.
Park and switch off the ignition.
Have it checked by a CITROËN dealer or a
qualified workshop.
Engine oil
pressure and
temperature on while
driving.
low pressure or a high
temperature. Park
  and   switch   off   the   ignition   then   allow   to   cool.
Visually
  check   the   level.
Chapter
  7,   "Levels"   section.
remaining on,
even though the
level  is   correct.a major fault. Have   it   checked   by   a   CITROËN   dealer   or   a  qualified
  workshop.
Each
 
time
 
the
 
vehicle
 
is
 
started:
 
a
 
series
 
of
  warning   lamps   comes   on   applying   a   self-test   check.  
They
  go   off   almost  
immediately

.
Engine
 
running:
 
the
 
lamp
 
becomes
 
a
 
warning   if   it   remains   on   continuously   or   flashes.
This
 
initial
 
warning
 
may
 
be
 
accompanied
 
by   an   audible   signal   and   a   message   in   the   screen.
Do
 
not
 
ignore
 
these
 
warnings.

33
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Coolant
temperature
and level on with needle
in the red
zone.
an abnormal increase in
temperature.
Park
  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
flashing. a
  drop   in   the   coolant   level.Chapter
  7,   "Levels"   section.
Contact
  a   CITROËN dealer   or   a   qualified  
workshop.
Service on

  temporarily. minor   faults   or   warnings.Consult
  the   alert   log   in   the   display   or   screen.
If your vehicle is equipped with a trip computer or
a
  screen:   refer   to   the   "Steering   mounted   controls"  
section

  in   Chapter   4.
Contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
remaining

  on. major   faults.
Seat belt not
fastened on then
flashing.
the
  driver   and/or   front  
passenger has not fastened
their

  seat   belt.Pull
  the   strap   then   insert   the   tongue   in   the   buckle.
accompanied
by an audible
signal then
remains
  on.the vehicle is moving with
the
  driver's   and/or   front  
passenger's seat belt not
fastened.Check

  that   the   seat   belt   is   fastened   by   pulling   the  
strap.
Chapter

  5,   "Seat   belts"   section.
ECO on.
The Stop & Start
system
has put the engine in STOP
mode following a vehicle
stop
  (red   light,   traffic   jam,  
etc...).As soon as you want to move of

f, the warning
lamp goes off and the engine restarts
automatically
  in   START
 
mode.
flashes
  for   a  
few seconds,
then

  goes   off.STOP mode is temporarily
unavailable.
or
START mode has been
invoked
  automatically.Chapter
  3,   "Stop   &   Start"   section.
READY TO GO
3

34
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Front / lateral
airbag flashing
  or  
remaining

  on.a
  failure   of   an   airbag.Have
  the   system   checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop   without   delay.
Chapter
  5,   "Airbags"   section.
Front
passenger's
airbag
deactivated on. the intentional deactivation
of this airbag in the
presence of a rearward
facing
  child   seat.Chapter
  5,   "Airbags"   or   "child   safety"   section.
Low fuel
level on with gauge
needle in the
red
  zone.When
  it   first   comes   on,  
there remains around
8 litres

  of   fuel   in   the   tank.  
The distance you can drive
on this fuel depends on
your style of driving and the
engine

  type.You
  must   fill   up   with   fuel   to   avoid   running   out.
This warning lamp comes on each time you
switch
  on   the   ignition   until   you   have   filled   up.
Capacity
  of   the   tank:   approximately   60   litres   (or  
55

  litres   according   to   version).
Never
  risk   driving   until   the   tank   is   empty,   this  
could

  damage   the   emissions   and   injection  
systems.
flashing. cutting of

f of the fuel supply
following
  a   serious   impact.Restore
  the   supply.
Chapter
  7,   "Fuel"   section.
EOBD
emission
control
system flashing
  or  
remaining

  on.a
  failure   of   the   system.There
  is   a   risk   of   damage   to   the   catalytic  
converter

.   Have   it   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Battery
charge on.
a fault in the charging
circuit. Check
  the   battery   terminals,   …
Chapter
  8,   "Battery"   section.
flashing. placing of the active
functions on standby
(economy
  mode).Chapter
  8,   "Battery"   section.
remaining on,
in spite of the
checks. an
  ignition   or   injection  
malfunction.Have

  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.

+ +
39
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
SCR emissions control system
Alerts InformationSolution - action
The UREA, Service and diagnostic warning lamps
come on, an SCR emissions control system fault
has
  been   detected. This is is temporary fault, the alert disappears as
soon as the exhaust emissions return to normal
levels.
After 30 miles (50 km) without AdBlue
®
Confirmation of the fault which is not related to a lack   of   fluid. The
  remaining   driving   range   700   miles  
(1   100   km).
Go   to   a   CITROËN   dealer   or   a   qualified   workshop  
as

  soon   as   possible   to   avoid   a   breakdown.
The
  fault   is   confirmed.
The next time the ignition is switched on, the
authorised driving range will be displayed in miles
(kilometres)
  and   the   alert   will   be   repeated   every  
30
  seconds.
The limit of the driving range has been reached,
exhaust
  emissions   levels   are   above   the   limits.
Starting
  is   impossible. To restart the engine, you must contact a
CITROËN
  dealer   or   a   qualified   workshop.
- BlueHDi Diesel
READY TO GO
3

40
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
FUEL GAUGEC OOLANT TEMPERATURE
The needle is positioned before the
red zone:
  normal   operation.
In arduous conditions of use or hot
climatic conditions, the needle may
move
  close   to   the   red   graduations.What you should do if the needle
enters the red zone:
Reduce your speed or let the engine
run
  at   idle.
What you should do if the warning
lamp comes on:
-
stop immediately
, switch off the
ignition.  
The
  fan   may   continue   to  
operate for a certain time, up to
approximately 10 minutes,
-

wait for the engine to cool down in
order

  to   check   the   coolant   level   and  
top

  it   up   if   necessary.
As the cooling system is pressurised,
follow the procedure below to avoid the
risk   of   scalding:
-
wait at least one hour after
switching of

f the engine before
carrying   out   any   work,
-  
unscrew
  the   cap   by   1/4   turn   to  
allow the pressure to drop,
-

when the pressure has dropped,
check

  the   level   in   the   header   tank,
- if necessary , remove the cap to
top up.
If the needle remains in the red
zone,
  have   the   system   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop.Refer

  to   chapter   7,   "Levels"  
section.
Refer

 
to
 
chapter
 
7,
 
"Fuel"
 
section.
The fuel level is tested each time the
key
 
is
 
turned
 
to
 
the
 
"running"
 
position.
The
 
gauge
 
is
 
positioned
 
on:
-

1:

 
the
 
fuel
 
tank
 
is
 
full,
 
approximately

 
60
 
litres.
-

0:

the reserve is now being used,
the warning lamp comes on
continuously.
 
The

 
reserve
 
when
 
the

 
warning
 
first
 
comes
 
on
 
is
 
approximately

 
8
 
litres.

47
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
SERVICE INDICATOR
This programmes service intervals
according  to   the   use   of   the   vehicle.More than 1 000 miles/km before the
next service is due
Example:
  4   800   miles/km   remain  
before

  the   next   service   is   due.   When  
the ignition is switched on and for a
few

  seconds,   the   screen   shows:
A few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance recorder resumes normal
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on and for a few
seconds,   the   spanner   flashes   and   the   number   of miles/kilometres

  remaining   is   displayed:
A few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance recorder resumes normal
operation
  and   the   spanner   remains   on.  
This indicates that a service should be
carried

  out   shortly.
Service overdue
Operation
A few moments after the ignition
has been switched on, the spanner
indicating a service operation comes
on; the display for the total distance
recorder
 
gives
 
(in
 
round
 
figures)
 
the
 
distance remaining before the next
service.
The points at which a service is due
are calculated from the last indicator
zero

 
reset.
The point at which a service is due is
determined
 
by
 
two
 
parameters:
-

the distance travelled,
-


the time which has elapsed since
the

 
last
 
service.
The distance remaining before the
next service may be weighted by
the time factor, depending on the
type
 
of
 
driving. With the engine running the spanner
remains on until the service has been
carried
  out.
For BlueHDi Diesel versions, this
alert
  is   also   accompanied   by   the   fixed  
illu

mination of the Service warning
lamp,
  on   switching   on   the   ignition.
Each time the ignition is
switched on and for a few
seconds, the spanner
flashes
  and   the   excess  
distance

  is   displayed.
For BlueHDi Diesel versions, the
spanner can also come on early,
according the level of deterioration
of
  the   engine   oil.   Deterioration   of   the  
engine oil depends on the conditions of
use

  of   the   vehicle.
READY TO GO
3

48
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Trip recorder zero
reset button
After this operation, if you wish
to  disconnect   the   battery,   lock  
the

 
vehicle   and   wait   for   at   least   five  
minutes, otherwise the zero re-set will
not

 
be   registered.
Engine oil level indicator
Depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service warning lamp,
accompanied by an
audible signal and a message in the
screen, indicates a low oil level which
could
  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge
fault
Flashing of "OIL--"
indicates a
malfunction of the
engine   oil   level   indicator.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.Dipstick
A = maximum, never exceed
this level as a surplus of oil
may
  damage   the   engine.
Contact a CITROËN dealer
or   a   qualified   workshop  
without

  delay.
B = minimum, top up the level
via   the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting reaches
the minimum


(or maximum) setting, release the
button then press it again to increase
(or
 
reduce)
 
the   brightness.
As soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.

51
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
6-SPEED ELECTRONIC GEARBOx
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It is only possible to come out
of position N
  if   the   brake   pedal   is  
pressed.
The change from position

A (driving in
automatic mode) to position M (driving
in manual mode) or vice versa can be
made
  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector must be in position N.
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

R, A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

N,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
Reverse gear Engaging reverse gear
Move the gear selector to R.
Only attempt to select reverse gear
when the vehicle is stationary.
Neutral Changing to neutral
Move the gear selector to N.
  If   the  
vehicle is moving, do not select this
position

  even   momentarily.
READY TO GO
3
Gearbox and steering wheel