2017 CHRYSLER PACIFICA instrument panel

TABLE OF CONTENTSSECTIONPAGE
1INTRODUCTION .
..............................................................3
2GRAPHICAL TABLE OF CONTENTS
.................................................7
3GETTING TO KNOW YOUR VEHICLE . . .
............................................13
4GETTING TO KNOW YOUR INSTRUMENT PANEL
.....................................211
5SAFETY
....................................................................265
6STARTINGANDOPERATING ....................................................379
7INCASEOFEMERGENCY .......................................................527
8MAINTAINING AND CARING FOR YOUR VEHICLE
....................................611
9TECHNICAL DATA
............................................................673
10MULTIMEDIA ...............................................................691
11CUSTOMER ASSISTANCE
.......................................................797
12INDEX .....................................................................805
1
2
3
4
5
6
7
8
9
10 11
12

GRAPHICAL TABLE OF CONTENTS
CONTENTS
FRONT VIEW ...........................8
 REAR VIEW ............................9
 INSTRUMENT PANEL ....................10 
INTERIOR .............................11
2

INSTRUMENT PANEL
Instrument Panel
1—AirVents
2 — Multifunction Lever
3 — Instrument Cluster
4 — Windshield Wiper Lever5 — Glove/Storage Compartment
6 — Ignition
7 — Steering Wheel
8 — Headlight Switch
10 GRAPHICAL TABLE OF CONTENTS

▫Multifunction Lever ...................113
▫ Turn Signals .........................114
▫ Lane Change Assist — If Equipped ........115
▫ High/Low Beam Switch ................115
▫ Flash-To-Pass ........................115
▫ Automatic High Beam — If Equipped .......115
▫ Battery Protection .....................116
 INTERIOR LIGHTS .....................117
▫ Courtesy/Interior Lighting ..............117
▫ Instrument Panel Dimmer Control .........118
 WINDSHIELD WIPER AND WASHERS ......120
▫ Intermittent Wiper System ...............121
▫ Windshield Wiper Operation .............121▫
Windshield Washers ....................121
▫ Mist Feature ........................ .122
▫ Rear Wiper And Washer .................122
▫ Rain Sensing Wipers — If Equipped ........122
 CLIMATE CONTROLS ..................124
▫ Manual Climate Controls – 3 Zone — If
Equipped .......................... .124
▫ Automatic Temperature Control (ATC) – 3 Zone
— If Equipped ...................... .132
▫ Operating Tips ...................... .146
 WINDOWS .......................... .149
▫ Power Windows ..................... .149
 TRI-PANE VISTA VIEW SUNROOF — IF
EQUIPPED .......................... .153
16 GETTING TO KNOW YOUR VEHICLE

(60 mm) rearward if the driver seat position is greater
than or equal to 2.7 inches (67.7 mm) forward of the
rear stop. The seat will return to its previously set
position when the ignition switch transtions out of the
LOCK position.
• When the ignition switch transitions out of the LOCK
position, the driver seat will move to a position 0.3
inches (7.7 mm) forward of the rear stop if the driver
seat position is between 0.9 – 2.7 inches (22.7 – 67.7
mm) forward of the rear stop. The seat will return to its
previously set position when the ignition switch tran-
sitions out of the LOCK position.
• The Easy Entry/Easy Exit feature is disabled when the
driver seat position is less than 0.9 inches (22.7 mm)
forward of the rear stop. At this position, there is no
benefit to the driver by moving the seat for Easy Exit
or Easy Entry. Each stored memory setting will have an associated Easy
Entry and Easy Exit Position.
NOTE:
The Easy Entry/Easy Exit feature can be enabled
or disabled through the programmable features in the
Electronic Vehicle Information Center (EVIC) or Driver
Information Display (DID). For further information refer
to “Display” in “Getting To Know Your Instrument
Panel”.
Heated Seats — If Equipped
Front Heated Seats — If Equipped
The front heated seats control buttons are located within
the climate or controls screen of the touchscreen.
You can choose from HI, LO or OFF heat settings. The
indicator lights in each switch indicate the level of heat in
use. Two indicator lights will illuminate for HI, one for
LO and none for OFF.
94 GETTING TO KNOW YOUR VEHICLE

Conversation Mirror
Located in the overhead console there is a conversation
mirror to view all the passengers in the vehicle. Push the
panel to release the drop down mirror. Raise the mirror
and push to latch it back in the stowed position.
EXTERIOR LIGHTS
Headlight Switch
The headlight switch is located on the left side of the
instrument panel. The switch controls the operation of
the headlights, parking lights, instrument panel lights,
interior lights and the fog lights.
Conversation Mirror
110 GETTING TO KNOW YOUR VEHICLE

Rotate the headlight switch clockwise to the second
detent for parking light and instrument panel light
operation. Rotate the headlight switch to the third detent
for headlight, parking light and instrument panel opera-
tion.
Automatic Headlights — If Equipped
This system automatically turns your headlights on or off
based on ambient light levels. To turn the system on, turn
the headlight switch to the extreme clockwise position
aligning the indicator with the AUTO on the headlight
switch. When the system is on, the Headlight Time Delay
feature is also on. This means your headlights will stay
on for up to 90 seconds after you turn the ignition switch
OFF. To turn the Automatic System off, turn the headlight
switch counterclockwise to the O (OFF) position.
NOTE:The engine must be running before the headlights
will come on in the Automatic mode.
Headlight Switch
1 — Rotate Headlight Switch
2 — Ambient Dimmer Control
3 — Instrument Panel Dimmer
4 — Fog Lamps Button
3
GETTING TO KNOW YOUR VEHICLE 111

Lane Change Assist — If Equipped
Tap the lever up or down once, without moving beyond
the detent, and the turn signal (right or left) will flash
three times then automatically turn off.
High/Low Beam Switch
When the headlights are turned on, pushing the multi-
function lever toward the instrument panel will switch
from low beams to high beams. Pulling back to the
neutral position returns the headlights to the low beam
operation.
Flash-To-Pass
You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will cause the headlights to turn on at high beam and
remain on until the lever is released.
Automatic High Beam — If Equipped
The Automatic High Beam system provides increased
forward lighting at night by automating high beam
control through the use of a digital camera mounted on
the windshield. This camera detects vehicle specific light
and automatically switches from high beams to low
beams until the approaching vehicle is out of view.
NOTE:Broken, muddy or obstructed headlights and
taillights of vehicles in the field of view will cause
headlights to remain on longer (closer to the vehicle).
Also, dirt, film and other obstructions on the windshield
or camera lens will cause the system to function improp-
erly.
To Activate
1. Select “Automatic High Beams — ON” through the Uconnect system. Refer to Uconnect Settings” in
“Multimedia” for further information.
3
GETTING TO KNOW YOUR VEHICLE 115