2017 AUDI TT COUPE remote control

Opening and closing
Power window
Controls
The driver can control all power windows.
Fig. 26 Driver's door: power w indow controls
All power window sw itches have a two-stage
function:
Opening and closing the windows
N
N
M 0 ::':, (X) m
"'To open or close the w indow completely, press
the switch down or pu ll the switch up br iefly to
the second level. The operation will stop if the
switch is pressed/p ulled aga in.
.. To se lect a position in between opened and
closed, press/pull the switch to the first level
until the desired window position is reached.
Power window switches
(D Left doo r
@ Right door
A WARNING
- Pay careful attention when closing the win­
dows. Pinching could cause serious injur ies.
- When locking the vehicle from outside, the
vehicle must be unoccupied since the win­ dows can no longer be opened in an emer­
gency .
(D Tips
- You can still open and close the windows for
approximately 10 minutes after turning the i gnition
off. The power windows do not
switch
off until the driver's door or front
passenger's door has been opened.
- When you open the doors, the w indows au­
tomatically lower approximately 10 mm.
32
· Convenience opening/closing
All windows can be opened and closed at the
same time.
Convenience opening feature
.. Press the~ button on the remote control key
until all windows reach the desired position.
Convenience closing feature
.. Press the (TI button on the remote control key
until a ll windows are closed~&. or
Convenience closing with the convenience
key*
.. Touch the sensor* on the door handle long
enough until all windows are closed . Do not
place your hand in the door handle when doing
this.
Setting convenience opening in the
Infotainment system
.. Select in the Infotainment system : IMENU! but­
ton
>Ve hicle > left control button >V ehicle set­
t in gs .
To enable the convenience window opening func­
tion, the
Long press to open windows function
must be switched
on .
A WARNING
-Never close the w indows carelessly or in an
uncontrolled manner, because this increas­
es the risk of injury.
- For security reasons, the windows can only
be opened and closed with the remote con­
trol key at a maximum distance of approx i­
mate ly 6 ft (2 m) away from the vehicle.
When pressing the~ button, always watch
the windows while they are closing so that
no one is pinched in the window. The closing
process will stop immediately when the~
button is released.

CD
CD
.... N
" N ...... 0
0
Ill co
Correcting power window malfunctions
You can reactivate the one-touch up/down func­
tion if it malfunctions.
~ Pull the power window switch up until the win­
dow is completely raised.
~ Release the switch and pull it up again for at
least one second .
Garage door opener
(Homelink)
Description
Applies to: vehicles with garage door opener (Homelink)
Fig. 27 Garage door o pen er: examples of usage for differ­
ent sy stems
With the garage door opener (Homelink), you
can act ivate systems such as the garage doors,
security systems or house lights from inside your
vehicle. Up to three remote control functions can
be programmed to the three buttons that are in­
tegrated in the control unit above the rearview
mirror.
To be able to operate systems using the garage door opener, the buttons in the control unit must
first be programmed .
A WARNING
When operating or programming the garage
door opener, make sure that no people or ob­
jects are in the area immediately surrounding
the equipment . People can be injured or prop­
erty can be damaged if struck when closing.
Open ing and closing
(D Tips
-For security reasons, we recommend that
you clear the programmed buttons before selling the vehicle.
- For add itiona l information about Homelink,
visit
www.homelink.com.
- For the Declaration of Conformity with the
provisions from the FCC in the United States
and Industry Canada, see ¢
page 304.
Operation
Applies to: vehicles with garage door opener (Home Link)
Fig. 28 Control pane l above the interior rearview mirror
Requirement: the button in the control panel
must be programmed ¢
page 34 and the vehi­
cle must be located within range of the system,
such as the garage door.
~ Press the button to open the garage door. The
green LED(!) blinks or turns on.
~ Press the button again to close the garage
door.
(D Tips
To open or close the garage door, do not press the button longer than 20 seconds or
the garage door opener will switch to pro­
gramming mode .
33

Opening and closing
Programming the transmitter
Applies to: vehicles with garage door opener (Homelink)
Fig. 29 Distance between t he rad iator grille and the re­
mote control transmitter
Programming the button : step 1 on the
control panel
1. Switch on the ignit ion.
2. Press both of the outside buttons on the con­
trol unit¢
page 33, fig. 28 until the yellow
LED @turns off and the green LED@ blinks.
This procedure clears the standard codes that
were set at the factory and does
not need to
be repeated again to program the other but­
tons.
3. Briefly press the button in the control panel
that you want to program.
4. Wait until the yellow LED@blinks. The pro­
gramming mode is active for 5 minutes.
5. Go in front of the vehicle with the original re­
mote control transmitter for the system that
you are programming to the control panel
button.
Programming the button: step 2 at the
radiator grille
6. Ho ld the remote control transmitter at the
vehicle radiator grille¢
fig. 29.
7. Now press the remote control transmitter
until the turn signals on your vehicle blink.
This can take up to 30 seconds.
8. If the emergency flashers blink three times,
the programming was successful.
If the
emergency flashers only b link one t ime, the
five-minute time limit for programming has
expired or the programming was unsuccess­
ful. Repeat the programming starting from
the third step or change the distance to the
radiator grille.
34
9. If the garage door or other systems do not
open with the Homelink buttons even if the
programming was successfu l, the system
may use a rolling code instead of a fixed
code. You must also then perform
rolling
code programming
c:, page 35.
The other two buttons in the control panel can be
programmed using the instructions given above.
Start with step 3.
Deleting button programming
The programmed buttons cannot be deleted indi­
vidually. They must be deleted all at once. Repro ­
gram the buttons if necessary.
.,.. Switch on the ign ition.
.,.. Press both of the outside buttons on the con­
trol unit until the yellow LED @turns off and
the green LED(!) blinks .
Reprogramm ing buttons
.,.. Switch on the ignition .
.,.. To reprogram an individual button, press the
desired button until the green LED @turns off
and the yellow LED@starts to blink (after ap­
proximately 20 seconds). Release the button
immediately. The programming mode is active
for 5 minutes.
.,.. Continue with step 5.
(D Tips
- The distance needed between the remote
control transmitter and the Homelink mod­
ule in the radiator grille
¢fig. 29 depends
on the system you are programming.
- Depending on the system model, you may
need to release the button on the remote
control transmitter while it is programming
and press it again . Hold every position you
try when programming for at least 15 sec­
onds before trying a new position. Keep an
eye on the vehicle turn signals while doing
this.

CD
CD
.... N
" N .... 0
0
Ill co
Digital compass
Switching the compass on and off
Applies to: vehicles with digital compass
Fig. 40 Rearview mirror : digita l compass is switc hed on
., To turn the compass on or off, press the button
@ until the compass display in the mirror turns
on or off.
The digital compass only works when the ignition is turned on . The directions are indicated with ab­
breviations :
N (north), NE (northeast), E (east),
SE (southeast), S (south), SW (southwest), W
(west), NW (northwest).
(D Tips
To prevent inaccurate compass readings, do
not bring any remote controls, electrical devi­
ces or metallic objects near the mirror .
Lights and V ision
Adjusting the magnetic zone
Applies to: vehicles with digita l compass
Fi g. 41 North Amer ica: magnetic zone map
., Press and hold the button (D ~ page 43, fig. 40
until the number of the magnetic zone appea rs
in the interior rearview mirror.
., Press the button
CD repeatedly to select the
correct magnetic zone. The selection mode
turns off after a few seconds .
Calibrating the compass
Applies to: vehicles wit h digita l compass
If the display is incorrect or inaccurate, the com­
pass must be recalibrated .
., Press and hold the button
CD until a C appears
in the interior rearview mirror .
., Drive in a circle at about 5 mph (10 km/h) until
a direction is displayed in the rearview mirror.
A WARNING
-
-To reduce the r isk to yourse lf and other driv-
ers, calibrate the compass in an area where
there is no traffic.
- Always pay attention to the traffic and the
area around your vehicle if you are reading
the compass while driving .
43

co
co
.... N
" N .... 0
0
Vl c:o
Warm and cold Climate control system
Description
The climate control system warms, cools and re­
moves humidity from the air in the vehicle interi­
or. It functions most effectively when the w in­
dows are closed. If there is a build-up of heat in ­
side the vehicle, ventilation can help to speed up
the cooling process.
Pollutant filter
The pollutant filter removes pollutants such as
dust and pollen from the air.
Key recognition
Certain settings are automatically stored and as­
signed to the remote contro l key being used .
A WARNING
Poor visibility can lead to accidents.
- For safer driving, keep all windows free of
ice, snow and fog.
- Become familiar as quickly as possible with
the correct use and function of the climate
control system, especially with the defrost­
ing and defogging function.
- When the temperature is below freezing,
only use the windshield washer system after
the windsh ield has been warmed by the cli­
mate control system. The washer fluid could
freeze on the windshield and impair visibili­
ty .
(D Note
-If you suspect that the climate control sys­
tem is damaged, switch the system off to
Warm and cold
prevent further damage and have it checked
by an authorized Audi dea ler or authorized
Audi Service Facility.
- Repairs to the Audi climate control system
require special technical know ledge and
special tools. See an authorized Audi dealer
or authorized Audi Service Facility.
(® For the sake of the environment
Reducing the amount of fuel used also re­
duces the amount of pollutants that enter the
air.
(D Tips
- To prevent interference with the heating
and cooling output and to prevent the win­
dows from fogging over, the air intake in
front of the windshield must be free of ice,
snow or leaves.
- Condensation from the cooling system can
drip and form a puddle of water under the
vehicle. This is normal and does not mean
there is a leak .
- The energy management system may switch
the seat heating* or rear window defroster
off temporarily . These systems are availab le
aga in as soon as the energy supp ly has been
restored.
- The flows through the vents under the rear
w indow . Make s ure the openings are not
covered when plac ing clothing on the lug­
gage compartment cover .
51

CD
CD
.... N
" N ...... 0
0
Ill co
have the malfunction corrected. To start the en­
gine, press and hold the
! START ENGINE STOPI
button.
DJ R emot e control key : hold b ack of key
again st the d esignated are a. See owner's man­
ual
This message appea rs if the re is no convenie nce
key inside the vehicle or if the system does not
recognize the key . The conven ience key may not
be recognized, for example, if it is cove red by an
object that
disrupts the signal (such as a brief ­
case), or if the key battery is weak. Electronic de­
vices such as cell phones can also interfere with
the signal.
To still be able to start or stop the eng ine, see
c:::> page 59, Starting the engine when there is a
malfunction .
Ill Remote control key : key not recogn ized . Is
the ke y still in th e vehi cle?
The Ill ind icator light turns on and this message
appears if the conve nience key was removed from
the vehicle when the engine was running.
If the
conven ience key is no longer in the vehicle, you
cannot switch the ign ition on or start the engine
once you stop it. You a lso cannot lock the vehicle
from the outside .
Please press brake p edal
This message appears if you do not press the
brake pedal when starting the eng ine.
Please pr ess clut ch p edal
This message appea rs in vehicles w it h manual
transmissions if you do not press the clutch pedal
when sta rting the engine . The engine can on ly be
started when t he clu tch pedal is pressed.
Pl ease select N or P
This message appea rs when starting or stopping
the eng ine if the selector lever is not in the Nor P
position . The engine will not start/stop.
Shift to P , otherw ise vehi cle can roll awa y.
Doors can be lo cked i n P only
This message appears for safety reasons a long
with a warning tone. It appears if the selector
lever for the automatic transmission is not in the
D rivi ng
P position when switch ing the ignit ion off w ith
the
I START ENGINE STOPI b utton. P lace these­
l ector lever in the P position. The veh icle cou ld
roll if the lever is not in P. You also cannot lock
the vehicle using the locking sensor on the door handle or using the conven ience key .
Starting the engine when there is a
malfunction
It may not be possible to start the engine under
certain circumstances, for example if th e battery
in the vehicle key is drained, if interference is af­
fected the key or if there is a system malfunc­
tion.
F ig. 61 Steering column/ remote control key: starting the
e n g in e if there is
a m alfunct ion
As long as the message y >l) Remote control key :
hold back of key against the designated are a.
See owner's manual
is displayed, you can emer­
gency start your vehicle.
.. Press the brake pedal
c:::> .&. in Starting the en­
gine on page 57.
... Press the ~I s=T ~A ~ R~ T~ E_N _G _I _N =E - S~ T= o- P~I button .
.,. Ho ld the master key in the location ind icated as
shown in the illustrat ion
y >l) c:::, fig. 61. The engine
w ill start.
.. If the engine does not automat ica lly start,
press the
! S TART ENGINE STOPI butto n again .
(D Tips
You can view the message aga in by pressing
the
I S TA RT ENGINE S TOP I button.
59

Assist
-The camera field of view¢ page 73, fig. 72 is
dirty or covered in ice. C lean this area on the
windshield.
- The camera field of view is fogged over. Wait
until the fog has cleared before switching the
active lane assist on again.
- The system has been unable to detect the lanes
for an extended period of time due to road con­
ditions. Switch active lane assist back on when
the lines are more visible.
Audi active lane assist: currently unavailable.
See owner's manual
There is a temporary active lane assist malfunc­
tion. Try switching the active lane assist on aga in
later.
Audi active lane assist: malfunction! See own­
er's manual
Drive to an authorized Aud i dea ler or authorized
Audi Service Facility immediately to have the
malfunct ion corrected.
Audi active lane assist: Please take over steer­
ing!
This message appears if you are not steering by
yourself. If th is is the case, active lane assist does
not switch off, but it is "not ready" to provide a
warn ing. The system can he lp you keep the veh i­
cle in the lane. However, you are responsible for
driving the vehicle and must steer it yourself.
Adjusting the steering time and v ibration
warning
A ppl ie s to: ve hicles w ith Audi active lane assis t
You can adjust individual active lane assist set­
tings in the Infotainment system.
Select in the Infotai nment system: I MENU I but­
ton>
Vehicle > left control button >Driver assis­
tance > Audi active lane assist
l) The correct ive stee ring fu nctio n is not availab le in all mar­
kets.
74
Steering time1>
Early: in this setting, the corrective steering hap­
pens continuously to help keep the vehicle in the
center of the lane.
Late : in this setting, the system provides correc­
tive steering just before a vehicle wheel touches a
detected lane marker line .
Vibration warning
You can switch the addit ional vibration warn ing
i n the steering wheel on or off.
'
@ Tips
In certain markets : your sett ings are stored
automat ica lly and assigned to the remote
control key in use.
Lap timer
Introduction
App lies to: vehicles wi th lap tim er
Lap timer
You can measure and analyze lap times with the
lap timer in the display. The time is measured in
minutes, seconds and 1/10 seconds. With lap
times longer than 60 minutes, the hour is also
shown and the display of 1/10 seconds is re­
moved.
The time measurement on an indiv idual lap ends
after 99 hours 59 minutes and 59 seconds. A
new lap starts automatically after that.
The measurement ends after a maximum of 30 laps. You can then eva luate the lap times or start
a new time measurement .
You can contro l the lap timer using the controls
on the multifunction steering wheel
¢ page 75.
A WARNING
Your focus should always be on driv ing your
vehicle safely. As the driver, you have com­
p lete respons ibility for safety in traffic. Only
-

co
co
.... N
" N .... 0
0
Vl c:o
The display brightness adjusts automatically to
the brightness of the surroundings, both in the information and in the warning stage. In very
dark or very bright surroundings, the automatic
adjustment will set the display to the minimum
or maximum level. In such cases, you may notice no change when adjusting the brightness, or the
change may only be noticeable once the sur­ roundings change.
Adjust the brightness to a level where the display in the information stage will not disrupt your
view ahead .
If you change the brightness, the dis­
play in the exter ior mirror will briefly show the
brightness level in the information stage. The
brightness of the warning stage is linked to the
brightness in the information stage and is adjust­
ed along with the information stage.
(D Tips
- Side assist is not active while you are ma k­
ing the adjustment.
- Your settings are automatically stored and
assigned to the remote control key being
used.
Messages
Applies to: veh icles with Audi side assist
If the side assist switches off automatically, a
message appears in the Infotainment system dis­
play.
@j Audi side assist : cur rently unavailable.
Sensor vision restricted due to surroundings.
See owner's manual
The radar sensors' vision is affected. Do not cover
the area in front of the sensors with bike wheels,
stickers, dirt or other objects . Clean the area in
front of the sensors, if necessary~
page 77,
fig. 80.
@j Audi side assist: currently unavailable.
See owner's manual
Side assist cannot be switched on at this time be­
cause there is a malfunction (for example, the
battery charge level may be too low).
Assist
@j Audi side assist: malfunction! Please
contact Service
The system cannot guarantee that it will detect
vehicles correct ly and it has switched off. The
sensors have been moved or are faulty . Have the
system checked by an authorized Audi dealer or authorized Audi Service Facility soon .
Audi drive select (drive
settings)
Introduction
Applies to : vehicles with Audi drive se lect
Drive select makes it possible to experience dif­
ferent types of vehicle sett ings in one veh icle .
The driver can select from three modes,
Comfort,
Auto
and Dynamic , using the ~t.~, button in the
center console or by using the Infotainment sys­
tem. This allows you to switch between a sporty
and a comfortable driving mode, for example. In
the
Individual mode, the settings can be adjust­
ed to your persona l preferences . This makes it
possible to combine settings such as a sporty en­
gine setting with light steering.
A WARNING
=
Using Audi drive select incorrectly can lead to
collis ions, other accidents and serious inju­
ries .
Description
Applies to: vehicles with Audi drive se lect
The vehicle setup in each mode depends on the
vehicle's features. However, the engine and
steering are always affected .
Engine and automatic transmission
Depending on the mode, the engine and auto­
matic transmission respond more quickly or in a
more ba lanced manner to accelerator pedal
movements.
Adaptive dampers (Audi magnetic ride)*
The adaptive dampers use sensors to record in­
formation regarding steering movements, brak­
ing and acceleration ope rations by the driver,
road surface, driving speed, and load. With d rive .,..
79