2017 AUDI S4 bolt pattern

Wheels
bolts and a special procedure. You must never
repair or disassemble them ¢
.&..
A WARNING
Wheel bolts that are tightened or repaired in­
correctly can become loose and result in loss
of vehicle control, which increases the risk of
an accident. For the correct t ightening specifi ­
cation, refer to ¢
page 348, Finishing .
-Always keep the wheel bolts and the
threads in the wheel hub clean and free of
grease .
- Only use wheel bolts that fit the rim .
- Always have damaged rims repaired by an
authorized Audi dealer or authorized Audi
Service Facility . Never repair or disassemble
rims yourself, because this increases the risk
of an accident.
Winter tires
W inter tires significantly improve the vehicle's
handling when driving in winter conditions. Be­
cause of their construction (width, compound,
tread pattern) , summer tires provide less trac­
tion on ice and snow.
.,. Use winter t ires on all four wheels.
.,. Only use winter tires that are approved for your
vehicle.
.,. Please note that the maximum permitted
speed may be lowe r with winter tires
q ,&. . An
authori zed Audi dealer or authori zed Audi Serv­
ice Facility can inform you about the maximum
permitted speed for your tires .
.,. Check the tire pressure after installing wheels
¢page 327.
The effectiveness of winter tires is reduced great­
ly when the tread is worn down to a depth of
0 .16 in (4 mm) . The characteristics of winter
tires also decrease great ly as the tire ages, re­
gardless of the remaining tread .
A WARNING
-Never drive faster than the maximum per­
mitted speed for your tires. This could cause
the tires to heat up too much. This increases
332
-
the risk of an accident because it can cause
the tire to burst.
- Always adapt your driving to the road and
traffic conditions . Drive carefully and reduce
your speed on icy or slippery roads . Even
winter tires can lose traction on black ice .
@ For the sake of the environment
Reinstall summer tires at the appropriate
time, because they prov ide better handling
when roads are free of snow and ice. Summer
tires cause less road noise, tire wear and fuel
consumpt ion .
(D Tips
You can also use all season tires instead of
winter tires. Please note that in some coun­
tries where winter tires are required, only
winter tires w ith the ~ symbol are permitted .
Snow chains
Snow cha ins not only improve the driving in win­
ter road condit ions, but also the braking.
.,. Only install snow chains on the
front wheels .
This applies a lso to vehicles with all wheel
drive* .
.,. Check and correct the seating of the snow
chains after driving a few feet, if necessary. Fol­
low the instructions from the manufacturer.
.,. Note the maximum permitted speed when driv­
ing with snow chains. Do not exceed 30 mph
(SO km/h) .
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons.
Check with an authorized Audi deale r or author­
ized Audi Service Facility to see if you may use
snow chains .
Use
fine-mesh snow chains. They must not add
more than 0.53 in (13 .5 mm) in height, including
the chain lock.
You must remove the snow chains on roads with­
out snow. Otherwise , you could impair driving
ability and damage the tires .

Emergency assistance
Removing and installing a wheel
Fig. 266 Wheel: internal hex socket to turn the whee l
bolts
Fig. 267 Whee l: alignment pin in the top ho le
Removing a wheel
., Remove the top wheel bolt complete ly using
the hex socket in the screwdriver hand le (in the
vehicle tool kit)
c::> fig. 266 and place it on a
clean surface .
., Install the alignment pin (from the vehicle tool
kit) by hand into the empty hole
c::> fig. 267 .
., Remove the rest of the wheel bolts.
., Remove the wheel. The alignment pin remains
in the hole while doing this.
Install a wheel
Read the directions on c:> page 348 when instal­
ling unidirectional tires.
., Slide the wheel on over the alignment pin.
., Install the wheel bolts and tighten gent ly using
the hex socket.
., Remove the alignment pin and also tighten the
remaining wheel bo lt .
., Carefully lower the vehicle using the vehicle
jack* .
., Tig hte n the wheel bolts i n a diagona l pattern
using the wheel wren ch.
348
The wheel bolts must be clean and loosen/tight ­
en easily . Check the contact surfaces for the
wheel and hub. Contam inants on these surfaces
must be removed before installing the wheel.
A WARNING
Never use the hex socket in the screwdriver
handle or the hex socket wrench w ith the
ratchet to loosen or tighten the wheel bolts.
This increases the risk of an accident, because
you will not reach the tightening specification
required.
(D Note
When removing or instal ling the wheel, the
r im could hit the brake rotor and damage t he
rotor. Work carefully and have a second per­
son help yo u.
@ Tips
- When mounting tires with unidirectional
tread design
make sure the tread pattern is
pointed the right way
c::> page 348.
- The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mati ng surfaces of both the wheel and the
hub. Remove all dirt from these sur faces be­
fore remounting the whee l.
Unidirectional tires
A unidirectional tire profile is identified by arrows
that point in the running direction on the tire
s idewall. You must always adhere to the speci­
fied running direction . Th is is necessary ensure
the tire's opt imum performance in regard to ad­
hesion, running noise, friction and hyd roplaning.
To benefit fully from the advantages of the uni­
directional tire design, you should replace faulty
tires as soon as possible and restore the correct
r un ning direction on all of the tires.
Finishing
., Re install the caps on the wheel bolts if neces­
sary .
., Store the vehicle tool kit in its designated
place . ..,.