2017 AUDI A8 clock

Cockpit overview
_& WARNING
The route calculated by the navigation system
is a recommendation for reaching your desti­
nation. Obey traffic lights, stopping restric­
tions, one-way streets, lane change restric­
tions, etc.
An asterisk
" *" in front of the street name in­
dicates that the information about this street
or this section of the route is not complete in
the navigation data that the MMI contains .
Obey traffic laws in one-way streets and pe­
destr ian zones.
Time and date display
Fig. 16 Center conso le: analog clock
The date and time are shown in the instrument
cluster display . There is also an ana log clock in
the center console
<=:> fig. 16 .
When you open the driver's door, the date and
time appear in the display for 30 seconds . When
the ignition is switched on, the time is always dis­
played in the status line © regardless of the cur­
rent d isplay.
You can set the time on both clocks and the date (disp lay) in the Infotainment system
<=:> page 204.
16
Head-up Display
Appl ies to: vehicles with Head-up D isplay
Fig. 17 Examp le : i ndicators in the Head-up Display
Fig. 18 Instrument panel: knob for th e head-up display
The Head-up Display pro jects certain warnings or
selected information from the assist systems* or
navigation* on the windshield. The display ap­
pears within the driver's field of vision.
Switching on/off
.,. To switch the Head-up Display on or off, press
the knob~ ¢
fig. 18.
Adjusting the height
The height of the display can be adjusted to the
i ndivid ual driver .
.,. Make sure you are seated correctly
<=:>page 208.
.,. Turn the knob~ to adjust the d isplay.
Settings in the Infotainment system
.,. Select: the I CARI function button > (Car)* Sys­
tems
contro l button > Driver assist > Head-up
display
> Head-up display contents or Display
brightness .

C) C0 ....
"' " "' .... 0 0 :r Storage
Cup holders
Fig. 75 Center co nsole : fro nt cup ho lders
F ig. 76 Sect io n of th e re ar bench se at: cu p ho lder in rear
center co nso le
Front cup holders
.. Tap on the cover to open the cup ho lde rs
Q fig. 75.
Cup holder s in the rear center console
.. Tap on the front strip to open the cup holders .
.. Set your beverage in the ho lder .
.. To close the cup holder , fold the cover back un-
t il it clicks into place.
In vehicles with a full-length center console in
the rear, the cup holder is located at @
9page 62, fig . 72.
A WARNING
-
- Do not p ut any hot beverages in the c up
holder while the vehicle is moving. Hot bev­
erages could spill, wh ich can cause injury .
- Do not use any breakable beverage contain­
ers (for example, made out of glass or po r­
celain). You cou ld be injured by them in the
event of an accident .
Seats and storag e
(D Note
Beverage containers in the cup holders should
a lways have a lid . If not , beverages could spill
and cause damage to vehicle equipment, such
electron ics or seat covers.
Cooled glove compartment
T he cooled glove compartment only functions
when the AIC system is swi tched on.
Fig . 77 G love co mpart ment: swi tching cooling mode o n/
off
.. Turn the knob @counter-clockwise to switch
the cooling on . The symbols on the knob ind i·
cate the correct posit ion.
.. Turn the knob @clockwise to switch the cool ·
ing off .
The glove compartment cooling mode only func­
t ions when the veh icle A/C system is switched on .
If the heating is switched on, switching the glove
compartmen t cooling mode off is recommended .
_& WARNING
Always leave the lid o n the glove compart­
ment cover closed while dr iving to red uce the
risk of injury .
a) Tips
The glove compartment can be locked using
the mechanical key.
Additional storage compartments
Yo u w ill find a range of storage compa rtments
and holders at different locations in the vehicle.
- Compartments in the doors
IJ,,
63

Driving
-If physical limitations prevent you from sit­
ting 10 in (25 cm) or more from the steer­
ing wheel, check with your authorized Audi
dealer to see if adaptive equipment is avail­
able .
- If the steering wheel is aligned with your
face, the supplemental driver's airbag can ­
not prov ide as much protection in an acci­
dent. Always make sure that the steering
wheel is aligned with your chest.
-Always hold the steering wheel with your
hands at the 9 o'clock and 3 o'clock posi­
tions to reduce the risk of personal injury if
the driver's airbag deploys.
- Never hold the steer ing wheel at the 12
o'clock position or with your hands inside
the steering wheel rim or on the steering
wheel hub . Holding the steering wheel the
wrong way can cause serious injuries to the hands, arms and head if the driver's airbag
deploys.
Entry assistance
Easy seat entry makes it easier to enter and exit the vehicle by adjusting the steering column au­
tomatically.
• In the Infotainment system, select the !CAR I
function button > Car systems control button >
Vehicle settings> Seats> Driver's seat> Easy
seat entry> On.
When easy seat entry is switched on, the steering
column goes back up into the park position when
the ignition is switched off. After entering the ve­
hicle, the steering column returns to the stored position once the ignition is switched on .
76
Starting and stopping
the engine
Starting the engine
The ! S TAR T ENGINE S T OPI button switches the
ignition on and starts the engine .
Fig. 90 Cente r conso le: START ENGINE STOP but ton
Switching the ignition on/off
• To switch the ignit ion on or off, press the
!START ENGINE STOPI button . Do not press the
brake pedal while doing this.
Starting the engine
• Press the brake pedal¢.&_.
• Press the
I START ENGINE STOP I button
¢
fig . 90 . The engine will start .
If the engine does not start immediately, the
starting procedure stops automatically after a
short time . Repeat the starting process .
Start/Stop system
Read the information in¢ page 78 , Start/Stop
system.
A WARNING
To reduce the risk of poisoning, never allow
the engine to run in confined spaces .
(D Note
Avoid high engine speed, full throttle, and
heavy engine load if the engine has not
reached operating temperature yet. You could
-
damage the engine. .,..

System settings
System settings
Setting the time and
date
You can set the clock time manually or using the
CPS.
Fig. 215 Sett ing a time zone
.,. Select : the I MENU I button > the upper left Time
control button (D <=> fig . 215.
Time source
GPS
'ti: the Time and Date are set by GPS based
on the
Time zone that was se lected manually. Al­
ways remember to set the new
Time zone i n the
MMI when the vehicle enters a different t ime
zone.
Manual : you can set the Time and Date manually
using the respective function . Press the control
knob. Set the
Time or the Date manually by turn­
ing and pressing the control knob.
Automatic daylight saving time*
When daylight saving time is sw itched On , the
time is moved forward or back automatically by
one hour when daylight sav ing time begins or
ends.
Man. daylight sav. time
When this function is switched On , an hour is
added to the set
Time.
Time zone
When selecting the appropriate time zone, a
sampling of countr ies in this zone will be listed .
204
Time format
If you select 24h , the clock will display, for ex­
amp le,
13:00. If you select AM/PM , the clock
will display, for example,
1:00 PM.
Date format
If you select DD.MM , the date will display, fo r ex­
ample,
31.12 . If you sele ct MM/DD , the date
will display, for example,
12/31.
Adjusting the sound
The sound distribution and volume of the MMI
can be adjusted individually. The settings depend
on vehicle equipment .
Fig. 216 Sound settings
Fig. 217 Adjusti ng the ba la n ce/fader
.,. Select: !T ONEI button.
(D GALA*/ DSP* / DSP [BOSE]*/ DSP [Bang
& Olufsen]*
- GALA (Speed-dependent volume increase) *:
select and confirm Active /Inactive for the ad­
justment of playback volume to the level of
noise inside the vehicle.
-Sound focus (adjusting the sound distribu­
tion) *:
select and confirm All (symmetrical

0 co .... N ,..... N .... 0 0 :c ' For detailed information on how to adjust the
driver's seat, see ¢
page 54.
A WARNING
Drivers who are unbelted, out of position or
too close to the airbag can be seriously in­
jured by an airbag as it unfolds. To help re­
duce the risk of serious personal injury:
- Always adjust the driver's seat and the
steering wheel so that there are at least 10 inches (25 cm) between your breastbone
and the steering wheel.
- Always adjust the driver's seat and the
steering wheel so that there are at least
4 inches (10 cm) between the knees and the
lower part of the instrument panel.
- Always hold the steering wheel on the out­
side of the steering wheel rim with your
hands at the 9 o'clock and 3 o'clock posi­
tions to help reduce the risk of personal in­
jury if the driver's airbag inflates.
- Never hold the steering wheel at the
12 o 'clock position or with your hands at
other positions inside the steering wheel
rim or on the steering wheel hub. Holding
the steering wheel the wrong way can cause
serious injuries to the hands, arms and head if the driver's airbag inflates.
- Pointing the steering wheel toward your face decreases the ability of the supplemen­
tal driver's airbag to protect you in a colli­
sion.
- Always sit in an upright position and never
lean against or place any part of your body
too close to the area where the airbags are
located.
- Before driving, always adjust the front seats and head restraints properly and make sure
that all passengers are properly restrained.
- Never adjust the seats while the vehicle is
moving . Your seat may move unexpectedly
and you could lose control of the vehicle.
- Never drive with the backrest reclined or
tilted far back! The farther the backrests are
tilted back, the greater the risk of injury due
to incorrect positioning of the safety belt
and improper seating position.
Driving safety
- Children must always ride in child seats
¢
page 248. Special precautions apply
when installing a child seat on the front passenger seat¢
page 226.
Proper seating position for the front
passenger
T he proper front passenger seating position is
important for safe, relaxed driving .
For your own safety and to reduce the risk of in­
jury in the event of an accident, we recommend
that you adjust the seat for the front passenger
to the following position :
... Adjust the angle of the seatback so that it is in
an upright position and your back comes in full
contact with it whenever the vehicle is moving.
... Adjust the head restraint so the upper edge is
as even as possible with the top of your head.
If
that is not possible, try to adjust the head re­
straint so that it is as close to this position as
possible ¢
page 210.
... Keep both feet flat on the floor in front of the
front passenger seat.
... Fasten and wear safety belts correctly
¢page 221.
For detailed information on how to adjust the
front passenger's seat, see ¢
page 54.
A WARNING
-Front seat passengers who are unbelted, out
of position or too close to the airbag can be
seriously injured or killed by the airbag as it
unfolds . To help reduce the risk of serious
personal injury:
- Passengers must always sit in an upright po­
sition and never lean against or place any part of their body too close to the area
where the airbags are located.
- Passengers who are unbelted, out of posi­
tion or too close to the airbag can be seri­
ously injured by an airbag as it unfolds with
great force in the blink of an eye . ..,
209

C) C0 ....
"' ,....
"' .... 0 0 :r (D Note
Never drive your vehicle until the fuel tank is
completely empty. The irregular supply of
fuel can cause misfiring. Gasoline could enter
the exhaust system and damage the catalytic
converter.
Fueling procedure
Fig. 253 R ight rear side of the vehicle: opening the fue l
f iller door
Fig. 254 Fu el fil ler door w ith attached fuel cap
The fuel filler door is unlocked or locked by the
central locking system.
Opening the fuel cap
"" Press on the left side of the fuel filler door to
open
c:!;> fig . 2 53.
""Unscrew the tank cap counterclockw ise.
"" Place the cap from above on the open fuel filler
door
c:!;> fig. 254.
Closing the fuel cap
""Screw the tank cap on to the right on the filler
neck until it cannot turn any farther .
""Then press on the left side of the tank door un­
ti l it latches .
Checking and Filling
Once the pump nozzle switches off, the fuel tank
is "full". Do not fill the tank more . Otherwise the
expansion space in the tank will be filled.
The correct fuel type for your vehicle can be
found on a label located on the inside of the fuel
filler door. For additional information on fuel,
see
c:!;> page 267.
The fuel tank capacity of your vehicle is listed in
the
Technical Data section c:!;> page 334.
To avo id fuel spilling or evaporat ing from the fuel
tank always close fuel cap properly and com­
pletely. An improperly closed fuel filler cap may
also cause the MIL lamp
c:!;> page 25 to come on.
A WARNING
Not paying attention when fueling or han­
dling fuel incorrectly can lead to fires, explo­
sions or serious injuries.
- Fuel ignites easily and can cause serious
burns and other injuries.
-
-If you do not switch the engine off when fu­
eling and/or do not insert the fuel nozzle
completely into the tank opening, fuel can
leak out or run over. Leaked fuel can ignite
and start a fire.
- Do not use the telephone while fueling. The
electromagnetic rays can cause sparks,
which can ignite fuel vapors and start a fire .
- Do not sit in your vehicle while fueling. If
you must make an exception and enter your
veh icle aga in while fueling, close the door
and touch metal to discharge static electric­
ity before touching the fuel nozzle. Static
electricity can create sparks, which can ig­
nite vapors when fueling.
- Do not smoke or have an open flame in the
area when fueling your vehicle or filling a
fuel container because this increases the
risk of an explosion.
- For your safety, carrying fuel containers in
your vehicle is not recommended. Whether
full or empty, the container can leak and
cause a fire in the event of an accident.
- If you must make an exception and trans­
port a fuel container, note the following:
269

Checking and Filling
Coolant addit iv e
The coolant additive is made of anti-freezing and
corrosion protection agents. Only use the fo llow­
ing coolant additives .
Coolant additive Sp ecification
G13 TL 774)
G12++ TL 774 G
These additives may be mixed with each other.
The amount of coolant additive that needs to be
mixed w ith water depends on the climate where
the vehicle will be operated . If the coolant addi­
tive percentage is too low, the coo lant can freeze
and damage the engine.
Coolant addi- Freeze protec-
tive tion
Warm regions min
. 40%,
min. -13 °F
max. 45% (-25 °C)
Cold regions min . 50%, max. -40 °F
max. 55% (-40
°C)
(D Note
-Before the start of winter, have your author­
ized Audi dealer or authorized Audi Service
F ac ility check if the coolant additive in you r
vehicle matc hes the percentage appropriate
fo r the clim ate. This is espe cially important
when driving in colder climates .
-If the appropriate coolant addi tive is not
available in an emergency, do not add any
other additive for risk of damaging the en ­
gine. If this happens, only use water and re­
store the correct mixture ratio with the
specified coolant additive as soon as possi­
ble.
- Only refill with new coo lant.
- Radiator sealant must not be mixed with
the coo lant.
278
Adding coolant
Fig. 261 E n g in e compartment: coolant expansion tank
cover
Observe the safety precautions ¢ .&. in Working
in the engine compartment on page 2 71.
Check ing the engine coolant level
.,. Park the vehicle on a level surface.
.,. Switch the ignit ion off.
.,. Read the coolant level on the coolan t expansion
tank
¢page 274. The coolant leve l must be be­
tween the M IN and MAX markings when the en­
gine in cold . When the engine is warm it can be
slightly above the MAX marking .
Adding coolant
Requirement: there m ust be a residua l amount of
coolant in the expansion t ank
~ CD.
.,. Let the engine cool down .
.,. Place a cloth
over the coolant expansion tank
cap and unsc rew the cap cou nte rclockw ise
~ .&. -
.. Add coolant mixed in the correc t ratio
~ page 277 up to the MAX marking.
.,. Make sure that the fluid level remains stable.
Add more coolant if necessary .
.,. Close the cap securely .
Coo lant loss usually indicates there is a leak . Im­
med iate ly drive your vehicle to an authorized
Audi dealer or authorized Audi Service Facility
and have the cooling system inspected.
If the
cooling system is not leak ing, a loss can come
from the coolant boiling through overheat ing
and being pushed ou t of the cooling system .

Emergency assistance
Emergency assistance
General information
... Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tir e, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
... Set up the warning triangle
r=;, page 312 .
... Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
Applies to: vehicles with warning triangle
Fig. 271 L uggage compa rtm ent lid : w arnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
... To remove the warning triangle, press the fas-
tener in the direction of the arrow and fold the
holder down.
The luggage compartment lid is only designed to
hold the warning triangle offered by th e Audi
Genuine Accessories program.
312
Vehicle tool kit
Applies to: vehicles with vehicle toot kit
Fig. 272 L u gg age compartmen t: cargo floor cove r fo lded
upward
Fig. 273 Luggage co m partment: exa mple of veh icle toot
kit and vehicle j ack
The vehicle tools and vehicle jack* are stored in
the luggage compartment under the floor cover .
... Lift the cargo floor by the plastic handle .
... Hook the handle into the luggage compartment
seal
r::> fig. 272 .
.,. Turn the handwheel counter-clockwise and re ­
move it .
.,. Remove the spare tire* to access the vehicle
tool kit
r::;, fig. 2 72 .
Depend ing on the equipment , the veh icle tool kit
may be located under the spare tire, under an­
other cover or in the tool box.
T he position of the vehicle jack* may vary .
A WARNING
Improper use of the veh icle jack can cause se ­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you .,..