2017 AUDI A7 warning light

co
co
,...,
N
" N ,...,
0
00
\.J ' ~ Clamp the charger terminal clamps to the jump
start pins according to the instructions. (pin un­
der the red cover = "positive", pin with hexago ­
nal head = "negative").
~ Insert the power cable for the charging device
into the socket and switch the device on .
~ At the end of the charging process, switch the
charger off and pull the power cab le out of the
socket.
~ Remove the c harge r te rmi nal clamps.
~ Close the red cover on the positive term inal.
~ Close the hood ¢ page 201.
A WARNING
- A highly explosive mixtu re of gases can form
when charging batter ies. On ly charge the
vehicle battery in well-vent ilated areas.
- A drained battery can freeze at tempera­
tures around 32 °F (0 °C). A frozen or
thawed vehicle battery must not be charged
and must not be used anymore . The battery
housing can crack and battery acid can leak
out if ice fo rms, wh ich increases the r is k of
an exp losion and chemical burns , Contact an
au thori zed Aud i dealer o r autho riz ed Aud i
Service Facility fo r more information.
- Do not con nect o r disconne ct the c harg ing
c able while charg ing be cause th is increases
the risk of an exp losion.
(j) Tips
- Only cha rge the vehicle bat tery through t he
con nections in the engine compartmen t.
- Read all of the manufacture r's instructions
fo r the charger befo re c harg ing the ve hicl e
batte ry.
Ch eck ing and Filling
Windshield washer
system
Fi g. 1 89 E ngine compar tmen t: washer f luid reservo ir cap
M N
-N ~
"' m
The windshield washer rese rvoir O contains the
cleaning so lution for the windshield and the
headlight washer system*
q page 202, fig. 184.
The reservoir capacity can be found in
¢page 262.
To reduce the risk of lime scale depos its on the
spray nozzles, use clean water with low amo unts
of calcium. Always add w indow cleaner to the wa­
ter. When the outside temperatures are cold, an
anti-freezing agent shou ld be added to th e water
so that it does not freeze .
(!) Note
-The concentration of ant i-freez ing agent
must be adjusted to the vehicle operat ing
conditions in the respective climate . A con­
centration that is too high can lead to vehi­
cle damage.
- Never add radiator anti-freeze or other addi­
tives to the washer fluid.
- Do not use a glass cleaner that contains
paint so lvents, because th is could damage
the paint.
Service interval display
The service in terval display detects when your ve­
hicle is due for service.
T he serv ice inte rval d isplay wo rks in two stages:
-Inspect ion or oil change rem inder: after a cer-
tain distance driven, a message appears in the ..,.
209

co
co
.... N
" N .... 0
00
\.J - Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
¢page 231.
ffim (T ire Pressure Monitoring System) T ire
pressu re : S ys tem malfunction !. If ffim
appears
after switching the ignition on or whi le driving
and the
[I] indicator light in the instrument clus­
ter blinks for approximate ly one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures¢
page 231. If
the ind icator light does turn off or turns on again
after a short period of time, dr ive to an author­
i zed A udi dealer o r authorized Audi Service Fac ili­
ty immediately to have the malfunc tion correct ­
ed .
& WARNING ,___ -
-If the tire pressure indicator appea rs in the
display, reduce your speed immed iate ly and
avoid any hard steer ing or braking maneu­
vers. Stop as soon as possib le and check the
t ires and their pressure.
- The driver is responsib le for maintaining the
correct tire pressure. You must check the
t ire pressure regu larly.
- Under certa in conditions (such as a sporty
driv ing style, winter cond itions or unpaved
roads), the tire p ressure monitoring system
indicator may be delayed.
{D) Tips
- The t ire pressure monitoring system can al­
so stop work ing when there is an ESC mal­
funct ion.
- Using snow chains may result in a system
malfunction .
- The t ire pressure monitoring system in your
Audi was calibrated with "Audi Orig inal
Tires"
¢ page 218. We recommend that you
use these t ires .
Wh eel s
Storing tire pressures
Applies to: vehicles with Tire Pressure Monitor ing System in­
dicator
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem.
.,. Make sure before storing that the tire pressures
of all four tires meet the specified values and
are adapted to the load
¢ page 221.
.,. Switch the ignit ion on.
.,. Select: the
I CAR ! funct ion button > ( C ar) * Sys­
tem s
contro l button > S ervic e & ch eck s> Tire
pres sure monitor > Store tire pre ssure > Yes,
s tore now .
(D Tips
Do not store the tire pressures if snow chains
a re installed.
Tire pressure monitoring
system
ill General notes
Each tire, including the spare (if provided),
shou ld be checked monthly whe n cold and inflat­
ed to the i nflat io n press ure recommended by the
vehicle manufacturer on the veh icle placard or
t ir e inflation pressure labe l. (If your ve hicle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
bel, you should determ ine the proper tire infla­
t ion pressure for those tires).
As an added safety feature, yo ur vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) that illuminates a low tire pressure tell­
ta le when one or more of your tires is signif icant­
ly under-inflated. According ly, when the low t ire
pressure te lltale illum inates, you sho uld stop and
chec k your tires as soon as possib le, and inflate
t h em to the prope r pressure. Dr iving on a sig nifi­
ca nt ly unde r-inflated t ire causes the t ire to over ­
hea t and can lead to tire fa il ur e. Under-inflat ion
also reduces fue l effic iency and tire tread life,
and may affect the vehicle's handling and stop -
ping ability .
liJJ,-
231

co
co
.... N
" N .... 0
00
<.,;) 'SI"
.. Se lect: the I CAR I function button > Car syst ems
> Se rvice & checks > Tire pres sure monitor >
Di splay ti re pres sure s.
The cu rrent tire press ures are shown in green and
ye llow numbers in the Infotainment system:
- Green : the cur ren t tire pressure and the speci­
fied tire press ure are app roxima tely the same.
- Yellow : the cu rrent tire pressu re is too low
comp ared to the specified ti re pressure.
The spec ified tire pressure is the last tire pres­
sure that was stored
c> page 233 .
Note that the tire pressure also depends on the
temperature of the t ire . The tire press ure in­
creases as the engine becomes warmer wh ile
d riving.
..&, WARNING
Read and follow the important inform ation
an d no tes
c> page 232.
@ Tips
The tire pressure or temperature a re not dis­
played in adaptation mode. Dashes --.-- are
show n in place of the press ure and tempe ra ­
ture.
CD Tire pressure loss
A pp lies to: ve hicles with tire p ressu re m oni toring sys tem
F ig . 19 5 Display : indicato r lig ht wit h a me ssage
If t he RI) indicato r light turns on, t he p ressure in
at least one t ire is too low o r new sensors were
n o t adapted :
Wheels
II] indicator light s turns on after turning the
ignition on
T he tire press ure is too low compared to the
specified press ure .
.. Check and store the tire pressure(s) the next
time it is possible
<:!> page 233 .
HE indicator light turns on while driving
Wheels with new sensors we re not adapted or
t h e tire p ressure h as reac hed a cr itica l level com­
pared to the specified p ressure.
.,. Avoid unnecessary steer ing and brak ing mane u-
vers.
.. Adapt your dr iving sty le to the sit uation.
.. Stop as soon as poss ible and check the tire(s).
.. If i t is possib le to continue dr iving , see an au-
thorized A udi dealer or authorized Audi Service
Facility immediately and have your tire(s) re­
paired or rep laced.
..&, WARNING
--
Read and follow the important info rmation
and notes
r=> page232 .
Storing new tire pressures
Applies to: vehicles wit h tire pressure monito rin g system
Correctly stored t ire pressure specifications are
necessary for reliable tire pressure monitoring.
.. Check the tire pressures in all whee ls .
.. Correct the t ire pressure if necessary . Refer to
the ti re pressure label for the recommended
tire pressure for your vehicle
c> page 221,
fig . 193.
On ly co rrect the pressure i n tires
whose temperature is app roximately the same
as the a mbient tempe ra tu re.
If the tempe ra­
t ure of t he tire is higher than t he ambien t air
t em pe rature, the t ire press ure must be in­
creased approximately 3 PSI (0, 2 bar) above
the value on the sticker .
.. Switch t he ignit ion on.
.. Select:
!CAR I function button> Car systems >
T ire pressure monitoring > Store tire pressu re.
After stori ng, the t ire pressure monitori ng sys­
tem meas ures t he curre nt t ire pressures and
sto res them as the new specified pressures .
233

Wheels
"'If the changed tire pressures are not displayed
in the Infotainment system, drive the vehicle
for approximately 10 minutes so that the sen­
sor signal from the wheels is received again.
During this adaptation phase, --.--is displayed
for the pressure and temperature and the tire
pressure monitoring system is only partially
available. It only provides a warning if one or
more t ire pressures is below the minimum per­
mitted specified pressure. If this is the case, the
Rt] indicator light appears with a message.
_& WARNING
Read and follow the important information
and notes
r::!;>page 232.
Malfunctions
Appl ies to : vehicles wi th tire pressure mo nito rin g system
If the Tire Pressure Monitoring System is not
avai lable, the
mm indicator light appears in the
driver information system. The
Rt] indicator light
also blinks for approximately one minutes each
time the ignition is switched on. The tire pressure
monitoring system cannot be selected in the In­
fotainment system. The following are examples
of situations that could cause a malfunction:
- If the message appears at the end of the adap­
tation phase, the system cannot detect the
wheels installed on the vehicle. This may result
from one or more wheels being installed with­ out wheel sensors or with incompatible wheel
sensors.
- A wheel sensor or another component has
failed.
- Using snow chains can affect the function of
the system because of the shield ing effect of
the cha ins.
- The tire pressure monitoring system is not
available due to a malfunction .
- Transmitters with the same frequency, such as
headphones or remote-controlled devices, may
cause a temporary system malfunction due to
the strong electromagnetic field.
The
mm indicator light turns off once the Tire
Pressure Monitoring System is available again.
If
you cannot correct the malfunction and the mm
234
indicator light stays on, drive immediately to an
authorized Audi dealer or authorized Audi Service Facility to have the malfunction repaired.

co
co
.... N
" N .... 0
00
\.J ' Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can a lso be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dealer or authorized
Audi Service Facility . Read and follow the instruc­
tions for use on the packaging.
A WARNING
- Us ing clean ing and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i­
soning .
@ For the sake of the environment
- Preferably purchase env ironmenta lly-friend­
l y cleaning products.
- Do not d ispose of leftover cleaning and care
products with household trash.
Car washes
T he longer that deposits remain on the vehicle,
the more the surface may be damaged. High
temperatures such as those caused by sunlight
increase the damag ing effect.
Befor e washing, rinse
off heavy depos its with
p lenty of water.
S tubborn depos its such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth.
A lso, wash t he un derside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your ve hicles w ith a pressure
washer, always follow t he ope rating inst ructions
p rovided w ith the pressure washe r. This is espe ­
cially important in regard to the pressu re and
sp raying distance. Do not a im the spray directly
at the sea ls on the side w indows, doors, lids or
Ca re and cleaning
the sun roof * or at tires, rubber hoses, ins ulating
material, sensors* or camera lenses* . Keep a dis­
tance of at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone noz zles o r high pressu re noz zles .
The water temperature must not be above 140 °F
(60 °C).
Automat ic car washe s
Spray off the vehicle befo re washing .
Make s ure that the wi ndows and roo f* are closed
and the windsh ie ld wipers are
off . Follow instruc ­
tions from the car wash operator, especially if
there are accessories attached to your vehicle .
If possible, use car washes that do not have
brushes .
Applies to: RS models: only use car washes where
t h e vehi cle rema ins s ta ti onary and the washi ng
equipmen t moves around the veh icle when wash ­
ing and drying. Car washes that move the ve hicle
th rough the car wash using a chain are not rec­
ommended.
Washing by hand
Clean the ve hicl e s tarting from the top and wor k­
ing down using a soft sponge or cleaning br ush .
Use solvent -free cleaning products.
Washing vehicles with matte finish paint by
hand
T o avo id damag ing the pa int when washing, firs t
remove dust and large pa rticles from your vehi­
cle . Insects, grease spots and fingerprints are
best removed w ith a special cleaner for matte
finish paint.
Apply the product using a microfiber cloth . To
avo id damaging the pa int surface, do not use too
much pressure .
Rinse the ve hicl e thorough ly w ith wate r. Then
clean using a neutra l shampoo and a so ft micro ­
fiber cloth .
Rinse the ve hicl e thoroug hly aga in and let it air
dry . Remove any water residue using a chamois. ..,.
235

Care and cleaning
A WARNING
- Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the braking effect
may be delayed due to mo isture on the
brake rotors or ice in the winter . This in­
creases the risk of an acc ident. The brakes
must be d ried first w ith a few careful b rake
applications.
(D Note
- If yo u wash the ve hicle in an automatic car
wash, yo u m ust retract the rear spoiler if
necessary, and fold the exte rior mi rrors in
to reduce the risk of da mage. Power fo ld ing
ex ter ior mirro rs* m ust only be folded in and
out using the power folding func tion.
-
- To red uce the risk of pa int damage, do not
wash the vehicle in direct sun light .
- T o reduce the risk of damage to the s urface,
do not use insect removing sponges, kitchen
sponges o r similar items .
- Matte finish painted vehicle components:
-To reduce the risk of damage to the sur-
face, do not use polis hing agents or hard
wax .
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint. The paint could be damaged
when the stickers or magnets are re­
moved.
@ For the sake of the environment
Only wash the veh icle in facili ties spec ially de­
s igned for that pu rpose . This will reduce the
r isk of dirty wate r contam inated with o il from
ente ring the sewe r system.
Cleaning and care information
W hen clean ing and ca ring for ind ividua l vehicle
components, refer to the fo llow ing tables. The
i n formation conta ined there is s imply recom­
mendations. For quest ions or for components t
h at are not listed, cons ult an autho rize d Aud i
dealer or au thor ized Aud i Servi ce Fac ility. Also
fo llow the informa tion found in <=> & .
Ext erior cleaning
Component Situation Solution
Windshield wiper
Deposits ¢ page 47, Cleaning windshield wiper blades
blades
Headlights /
Deposits Soft sponge wi th a m ild soap solution3>
Tail light s
Sensors /
Deposits Sensors: soft cloth with solvent-free cleaning solution
camera lens es Camera lenses: soft cloth w ith alcohol -free cleaning solu -
tion
Snow/ice Hand br ush/solvent-free de-icing spray
Wheels Road salt Water
Bra ke dust Acid-free special cleaning solution
Exhaust tail pipes Road salt Water, clea ning solution su itab le for s tainl ess stee l, if nee-
essa ry
236

Care and cleaning
Component Situation Solution
Te xtil es
Deposits adhering to Vacuum cleaner
a rt ifici al le ather , the surface
Alcant ara Water-based deposits Absorben
t cloth and mild soap solutiona>
such as coffee, tea,
blood, etc.
O il-based deposits Apply a m ild soap solution a), blot away the dissolved oil or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain remover, b lot with absorbent material, treat
as ink, na il polish, la- afterward with mild soap solution, if necessary a)
tex paint, shoe pol-
ish, etc.
Natural leather Fresh stains Cotton cloth with a mi
ld soap solutiona>
Water-based deposits Fresh sta ins : absorbent cloth
such as coffee, tea, Dried sta ins: stain remover suitable fo r leather
blood, etc.
Oil-based deposits Fresh stains: absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc. Dried sta ins : grease dissolv ing spray
Special deposits such Spot remover suitab le for leather
as ink, nai l polish, la -
tex paint, shoe pol-
ish, etc.
Ca re Regularly apply cond ition ing cream that protects from
light and penet rates into the materia l. Use specia lly-co l-
ored conditioning cream, if necessary.
Carbon parts Deposits clean the same way as plastic parts
a) Mild soap solution: maximum two tablesp oons of neutral soap in 1 quart (l liter) of water
_& WARNING
The windshie ld may not be trea ted with wa­
ter-repelling windshield coating agents. Un­
favorable conditions s uch as wetness, dark­
ness, or low sun can result in increased glare .
Wiper blade chatter is also possible.
(D Note
- Headlights /tail light s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form.
- Wheels
238
-
- Never use any paint polish or other abra­
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Sensors /camera l enses
- Neve r use wa rm or ho t water to remove
snow or ice from the camera lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning materials or
a lcohol to clea n the camera lens . This
could cause scratches and cracks .
-Doo r window s
-Remove snow and ice on windows and ex-
terior mirrors with a plast ic scraper. To

co
co
.... N
" N .... 0
00
\.J ' -If the tire is too severely damaged, see an
authorized Aud i dealer or authorized Audi
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized A udi
Service Facility for disposal.
@ Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.. After you experience a tire failure, pull the car
well away from moving traffic and try to reach
level ground before you stop c::> &.,.
.. All passengers should leave the car and move
to a safe location (for instance, beh ind the
guardrai l) ¢ ,&. .
.. Engage the
parking brake to prevent your vehi­
cle from rolling unintentionally ¢,&. .
.. Move
selector lever to position P ¢ ,&. .
.. If you are towing a trailer, unhitch the trailer
from your vehicle .
.. Take the
jack and the spare tire* out of the lug­
gage compartment ¢
page 240.
.8, WARNING
You or your passengers could be injured while
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance
off the road. Turn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
Emergency assistance
- To help prevent the vehicle from moving
suddenly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be­
ing changed . When one front wheel is lifted
off the ground, placing the Automatic
Transmission in P (Park) wi ll
not prevent the
veh icle from moving.
- Before you change a wheel, be sure the
ground is leve l and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
pa rtment
¢page 135.
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con­
trols for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the jack ¢
page 245 .
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order.
1. Activate the vehicle jack mode*¢ page 245.
2. Remove the decorative wheel cover* or the
wheel bolt caps*. For more details see also
¢ page 244, Decorative wheel covers or
¢ page 244, Wheels with wheel bolt caps .
3. Loosen the wheel bolts ¢page 245.
4. Locate the proper mounting point for the
jack and align the jack below that point
¢page 245.
5. Raise the car with the jack¢ page 245 .
6. Remove the wheel with the flat tire and then
install
the spare ¢ page 247.
7. Tighten all whee l bolts lightly.
8.
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and
firmly tighten
all wheel bolts
c::>page 245.
10. Replace the decorative wheel cover* or the
wheel bolt caps*.
11. Deactivate the vehicle jack mode* in the
MMI:
I CARI funct ion button> (C ar )* systems .,.
243