2017 AUDI A6 wheel

co
co
.... N
" N .... 0 0 <..:l 'SI"
Loosening
• Slide the wh eel wr ench onto the wheel bolt as
far as it will go.
• Take tight hold of the
end of the wrench handle
and turn the wheel bolts
counter-cloc kwise
about one single turn in the direction of arrow
<=>fig. 197.
Tightening
• Slide the wheel wrench onto the wheel bolt as
far as it will go.
• Take tight hold of the
end of the wrench handle
and turn each wheel bolt
cloc kwise until it is
seated.
A WARNING
- Do not use force or hurry when changing a
wheel· you can cause the vehicle to slip off
the jack and cause se rious personal injur ies.
- Do not loosen the wheel bolts more than
one turn
before you raise the vehicle with
the jack. -You risk an injury.
(D Tips
- Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bo lts .
- If a wheel bolt is
very tight, you may find it
easier to loosen by carefully push ing down
on the end of the wheel bo lt wrench with
one
foot only . As you do so, hold on to the
car to keep your balan ce and take care no t
to slip .
Emergen cy a ssis tanc e
Raising the vehicle
The vehicle must be lifted with the jack first be­
fore the wheel can be removed.
Fig . 1 98 Sill panels: markings
0, ...
0
---~~ i~~:--~
F ig . 1 99 Sill: posit ioning the vehicle jack
• Activate the vehicle jack mode* in the MM I:
!CARI function button > (Car )* s ystem s control
button
> Ser vicin g & checks > A ir su sp .: jac k
m ode > On .
• Engage the pa rki ng br ake to prevent your veh i­
cle from rolling unintentionally .
"' Move the
selector l eve r to position P .
"' Find the mark ing (imprint) o n the sill that is
nea rest the wheel that will be changed
<=> fig. 198 . Behind t he marking, there is a lift ­
ing point on the sill fo r th e vehi cle jack.
• Applies to: vehicles with a si ll: Remove the
cov ­
er from the sill before lifting the vehicle with a
vehicle jack<=>
page 240.
"'Turn the vehicle jack located under the lifting
point on the sill to raise the jack until its arm @
<=> fig . 199 is located under the designated plas­
tic mount <=> &. <=>0 .
"' Alig n the jack so that its arm@¢
fig. 199 en­
gages i n the designated lifting point in the door
sill and the movable b ase @ lies flat o n the
gro und. The base @ must be
vertical under the
lifting point@.
Ii"'
239

Emergency assistance
.,. Wind the jack up further until the flat tire
comes off the ground
c:::> A_ .
Position the vehicle jack only under the designat­
ed lifting points on the sill
c:::> fig. 198. There is ex­
actly
one location for each wheel. The jack must
not be positioned at any other location
c:::> ,1. c:::>Q) .
An unstable surface und er the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground. If necessary
place a sturdy board or similar support under the
jack . On
hard, slippery surfaces (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c:::> ,1..
A WARNING
- You or your passengers could be injured
wh ile chang ing a wheel if you do not follow
these safety precautions:
- Position the vehicle jack on ly at the desig­
nated lifting points and align the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack.
- On hard, sl ippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and yo ur
passengers:
- Do not raise the vehicle until you are sure
the jack is securely engaged.
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
- Changes in temperature or load can affect
the height of the vehicle.
240
(D Note
Do not lift the vehicle by the si ll. Position the
vehicle jack only at the des ignated lift ing
points on the sill. Otherw ise, your veh icle will
be damaged.
@ Tips
The vehicle jack mode * switches off automati­
cally at speeds above 6 mph (10 km/h).
Removing and installing the sill extension
cover
App lies to: vehicles with sill extension
Fig. 200 S ill: r em ov ing the cover
.. Pull the cover down to remove it. c:::> fig. 200
.. To install the cover, insert it in the mount and
press it upward until it clicks into place . The
cover must be flush with the surface of the sill
extens ion.
@ Tips
Some models may also have a cover for the
rear vehicle lift point.

co
co
.... N
" N .... 0 0 <.,;) 'SI"
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel.
Fig. 201 Changing a wheel: us ing the screwdriver hahd le
(with the blade removed} to turn the bolts
F ig. 202 C hangin g a whee l: alignment pin ins ide the top
hole
After you have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and re­
p lace the whee l as follows:
Removing th e wheel
.. Use the hexagon al so cket in the screwdri ver
handle
to completely remove the topmost
wheel bolt and set it aside on a
clean surface
¢ fig. 201 .
.. Screw the threaded end of the alignment pi n
from the tool kit hand-tight into the empty bolt
hole ¢
fig. 202 .
.. Then remove the other wheel bolts as described
above .
.. Take
off the wheel leaving the a lignment pin in
the bolt ho le ¢ 0 .
Puttin g on the spa re wh eel
.. Lift the spare wheel and carefully slide it over
the alignment pin to guide it in place ¢0 .
Em ergen cy a ssis tanc e
.. Use the hexagonal socket in the screwdr iver
handle to screw in and tighten all wheel bolts
slightly.
.. Remove the alignment pin and insert and tight­
en the remaining wheel bo lt slight ly like the
rest .
.. Tu rn the jack handle counter-clockw ise to lower
the vehicle unt il the jack is fully released .
.. Use the wheel bo lt wrench to t ighten a ll wheel
bol ts fi rmly¢
page 238. Tighten them cross­
wise,
from one bo lt to the (approx imately) op­
posite one, to keep the wheel centered.
(D Note
When removing o r insta lling the wheel, the
rim could h it the brake rotor and damage t he
rotor . Work carefully and have a second per­
son help you .
@ Tips
Never use the hexagonal socket in the hand le
of the screwdrive r to loosen or t ighten the
whee l bolts.
- Pull the reversible blade from the screwdriv ­
er before you use the hexagonal socket in
the handle to turn the whee l bolts.
- When mount ing tires with
unidirectional
tread de sign
make sure the tread pattern is
pointed the right way¢
page 241 .
-The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Usi ng a sp are t ire w ith a tread patte rn
intended f or u se in a sp ecific direction
When using a spare tire with a tread pattern in­
tended for use in a specific direction, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire. "'
241

Emergency assistance
-If the spare tire has to be installed in the incor ­
rect direction, use the spare tire only tempora­
rily since the tire w ill not be able to achieve its
optimum performance characteristics with re­
gard to aquaplaning, noise and wear.
- We recommend that you pay particular atten­
tion to this fact during wet weather and that
you adjust your speed to match road condi­
tions.
- Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unidirec­
tional tire .
Notes on wheel changing
Please read the informat ion ~ page 217, New
tires or wheels
if you are going to use a spare tire
which is different from the tires on your vehicle.
After you change a tire:
-Check the tire pressure on the spare tire im­
mediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station .
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb
(120 Nm) .
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
_& WARNING
- If you are going to equ ip your vehicle with
tires or rims which differ from those which
were factory installed, then be sure to read
the information
~ page 217, New tires or
wheels .
242
-Always make sure the damaged wheel or
even a flat tire and the jack and tool kit are
proper ly secured in the luggage compart­
ment and are not loose in the passenger
compartment.
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the
ve­
hicle.
- Always store damaged w heel, jack and tools
securely in the luggage compartment. Oth­
erwise, in an accident or sudden maneuver
they could fly forward, causing in jury to pas­
sengers in the vehicle.
Spare tire
Space-saving spare tire
App lies to : vehicles wit h spare tire
Fig. 203 Luggage com partment: space-sav ing spare t ire
The spare tire is intended for short -term use on­
l y . Have the damaged tire checked and, if neces­
sary, replaced by an authorized Audi dealer or au­
thorized Audi
Serv ice Facility as soon as possible .
There are some restr ictions on the use of the
spare tire. The spare tire has been designed spe­
cifica lly for your type of vehicle . Do not replace it
with the spare tire from another type of vehicle .
Space-saving spare tire*
The tire pressure must be 61 PSI (4.2 bar).
Removing the spare tire
"' Lift the cargo floor using the plastic handle and
hook the hand le onto the luggage compa rt­
ment seal
~fig . 203.
"'Tur n the handwheel counter-clockwise and re­
move it.

-Before you check anything in the engine
compartment, always read and heed all
WARNINGS
o page 198.
(D Note
Improper hook-up of jumper cables can ruin
the generator.
-Always connect POSITIVE( +) to POSITIVE
(+), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw plugs on the battery
cells are screwed in firmly. If not, t ighten
plugs prior to connecting clamp on negative
battery terminal.
- Please note that the procedure for connect­
ing a jumper cable as described above ap­
plies specifically to the case of your vehicle
being jump started. When you are giv ing a
ju mp start to another vehicle, do
not con­
ne ct the negative( -) cab le to the negative
(-) terminal on the discharged ba ttery @
o fig. 209. Instead, securely connec t the
negative (-) cable to either a solid metal
component that is firm ly bolted to the en­
gine block or to the engine block itself. If
the battery that is be ing charged does not
vent to the outs ide, escaping battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing .
The following information is to be used by com­
mercial tow truck operators who know how to op­
erate the ir equipment safely.
-Never tow your Audi. Towing will cause dam­
age to the engine and transmission .
- Never wrap the safety chains or winch cables
around the brake lines.
- To prevent unnecessary damage, your Audi
must be transported with a flat bed truck .
co
co -To load the vehicle on to the flat bed, use the ....
~ towing loop found in the vehicle tools and at-N .... 0 0 <.,;) 'SI"
Emergency situations
tach to the front or rear anchorage
opage251 and opage252.
.&_ WARNING
-
A vehicle being towed is not safe for passen-
gers. Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Fig. 210 Front bumper: cover
Fig. 211 Front bu mper: insta lling t he towing loop
The threaded open ing for the towing loop is lo­
cated behind a cover on the right side of the front
bumper .
.,. Remove the towing loop from the vehicle too l
kit
c:::, page 236.
.,. Press the cap inward with brief, forceful pres ­
sure
o fig. 210 . The cap will loosen from the
bumper.
., Tighten the towing loop in the threaded open­
ing until it stops
r:';> fig. 211 and then tighten it
w ith a wheel wrench .
.,. After usi ng, p lace the towing loop back in the
veh icle tool kit . "'
251

Emergency situations
_& WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be
pulled out when towing the vehicle and that
could cause an accident.
Rear towing loop
0 0
Fig. 212 Re ar bumper : cover
0 0
F
ig. 213 Re ar bumpe r: in stalli ng the towing loop
The threaded open ing is loca ted in the bumper
on the right rear side .
.,. Remove the towing loop from the vehicle tool
kit
c> page 236 .
.,. Press the cap inward with brief, forceful pres­
sure
c> fig . 212 . The cap will loosen from the
bumper .
.,. Tighten the towing loop in the threaded open­
ing until it stops
c>fig. 213 and then tighten it
with a wheel wrench .
.,. After using, place the towing loop back in the
vehicle tool kit.
8_ WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be
252
-
pulled out when towing the vehicle and that
could cause an accident .
Loading the vehicle onto a flat bed truck
Fig. 214 Vehicle on f lat bed tru ck
Front hook up
:;i N 0 t!, .., m
.,. Align the vehicle with the centerl ine of the car
car rier ramp .
.,. Attach the winch hook to the front towline eye
previously installed.
Rear hook up
.,. Align the vehicle wi th the centerl ine of the car
car rier ramp .
.,. Attach the w inch hook to the rear towline eye
previously installed.
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp .

Consumer information
scope of maintenance and repairs which can be
carried out by vehicle owners.
Also, safety and
environmental
concerns place very strict limits
on the nature of repairs and adjustments to en­
gine and transmission parts which an owner can
perform .
Maintenance, adjustments and repairs usually re­
quire special tools, testing devices and other
equipment available to specially trained work­
shop personnel in order to assure proper per­
formance, reliability and safety of the vehicle and
its many systems .
Improper maintenance, adjustments and repairs
can impair the operation and reliability of your
vehicle and even void your vehicle warranty.
Therefore, proof of servicing in accordance with
the maintenance schedule may be a condition for
upholding a possible warranty claim made within
the warranty period.
Above all, operational safety can be adversely af­
fected, creating unnecessary risks for you and
your passengers.
If in doubt about any servicing, have it done by
your authorized Audi dealer or any other properly
equ ipped and qualified workshop. We strongly
urge you to give your authorized Audi dealer the
opportunity to perform all scheduled mainte­
nance and necessary repairs. Your dealer has the
facilities, original parts and trained specialists to keep your vehicle running properly.
Performing limited maintenance yourself
The following pages describe a limited number of procedures which can be performed on your vehi­
cle with ordinary tools, should the need arise and
trained personnel be unavailable. Before per­
forming any of these procedures, always thor­
oughly read all of the applicable text and careful­
ly follow the instructions given. Always rigorously
observe the
WARNINGS provided.
Before you check anything in the engine com­
partment, always read and heed all WARNINGS
c> & and c> & in Working in the engine compart­
ment on page 198.
260
A WARNING
-
-Serious personal injury may occur as a result
of improperly performed maintenance, ad­
justments or repairs .
- Always be extremely careful when working
on the vehicle. Always follow commonly ac­
cepted safety practices and general com­
mon sense. Never risk personal injury.
- Do not attempt any of the maintenance,
checks or repairs described on the following pages if you are not fully familiar with these
or other procedures with respect to the ve­ hicle, or are uncertain how to proceed.
- Do not do any work without the proper tools
and equipment. Have the necessary work
done by your authorized Audi dealer or an­
other properly equipped and qualified work­
shop.
- The engine compartment of any motor vehi­
cle is a potentially hazardous area. Never
reach into the area around or touch the radi­
ator fan. It is temperature controlled and
can switch on suddenly - even when the en­
gine is off. The radiator fan switches on au­
tomatically when the coolant reaches a cer­
tain temperature and will continue to run
until the coolant temperature drops.
- Always switch off the ignition before anyone
gets under the vehicle.
- Always support your vehicle with safety
stands if it is necessary to work underneath
the vehicle. The jack supplied with the vehi­
cle is not adequate for this purpose and
could collapse causing serious personal in­
Jury.
- If you must work underneath the vehicle
with the wheels on the ground, always make
sure the vehicle is on level ground, that the
wheels are always securely blocked and that
the engine cannot be started.
- Always make sure the transmission selector
lever (automatic transmission) is in P (Park
position) and the park brake is applied. ..,

co
co
.... N ,..._
N .... 0 0 <..:l - Numbers and
Symbols
4-zone deluxe automatic climate control 60
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Key recognition . . . . . . . . . . . . . . . . . . . . . . 60
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Res idual heat . . . . . . . . . . . . . . . . . . . . . . . . 64
Synchronizing . . . . . . . . . . . . . . . . . . . . . . . . 64
A
A/C (4-zone deluxe automatic climate
control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A/C (deluxe automatic climate control) 61
ABS
refer to Anti-Lock Braking System . . . . . . 120
Accessories . . . . . . . . . . . . . . . . . . . . . . . 55, 261
Active lane assist . . . . . . . . . . . . . . . . . . . . . . 96
Adjusting the vibration warning . . . . . . . . . 98
Cleaning the camera area . . . . . . . . . . . . . 232
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 97
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Switching on/off . . . . . . . . . . . . . . . . . . . . . 97
Adaptive air suspension . . . . . . . . . . . . . . . . 104
Adaptive cruise control . . . . . . . . . . . . . . . . . . 88
braking guard . . . . . . . . . . . . . . . . . . . . . . . . 93
Cleaning the sensor . . . . . . . . . . . . . . . . . . 232
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Request for driver intervention . . . . . . . . . . 93
Stop -and -go traffic . . . . . . . . . . . . . . . . . . . 91
AdBlue. ... .. .. ................ ..... . 194
Me ssages . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Opening the tank door . . . . . . . . . . . . . . . . 195
Refilling . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Adjusting air distribution (4-zone deluxe auto­
matic climate control) . . . . . . . . . . . . . . . . . . 63
Adjusting a ir distribution (deluxe automatic
climate control) . . . . . . . . . . . . . . . . . . . . . . . 61
Adjusting the temperature (4-zone deluxe au ­
tomatic climate control) . . . . . . . . . . . . . . . . 63
Adjusting the temperature (deluxe automatic
climate control) . . . . . . . . . . . . . . . . . . . . . . . 61
advanced key
refer to Convenience key . . . . . . . . . . . . . . . 70
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Index
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . 167
Advanced Airbag-System . . . . . . . . . . . . . . 151
Advanced Airbag System components . . . 154
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Children . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Child restraints . . . . . . . . . . . . . . . . . . . . . 173
Components (front airbags) . . . . . . . . . . . 154
Danger of fitting a child seat on the front
passenger seat . . . . . . . . . . . . . . . . . . . . . . 148
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Front airbags .... .. ............. 151, 152
How do the front airbags work? . . . . . . . . 157
How many airbags does my vehicle have? 154
How the Advanced Airbag System compo-
nents work together . . . . . . . . . . . . . . . . . 156
Important information . . . . . . . . . . . . . . . 147
Impo rtant safety instructions on the knee
airbag system . . . . . . . . . . . . . . . . . . . . . . . 165
Knee airbags. . . . . . . . . . . . . . . . . . . . . . . . 163
Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . 159
PASSENGER A IR BAG OFF light . . . . . . . . . 159
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Safety instructions . . . . . . . . . . . . . . . . . . . 161
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . 165
S ide curta in airbags . . . . . . . . . . . . . . . . . . 168
Warning/Indicator lights . . . . . . . . . . . . . 159
When must the system be inspected? 159
Air pressure (tire pressure monitoring
system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Air suspension . . . . . . . . . . . . . . . . . . . . . . . 104
Alignment pin (tire changing) . . . . . . . . . . . 236
All season tires . . . . . . . . . . . . . . . . . . . . . . . 225
All weather lights . . . . . . . . . . . . . . . . . . . . . . 41
All wheel drive . . . . . . . . . . . . . . . . . . . . . . . 124
Alternator
refer to A lternator (indicator light) . . . . . . 14
Alternator (indicator light) . . . . . . . . . . . . . . 14
Amb ient lighting . . . . . . . . . . . . . . . . . . . . . . 44
Anti-freeze Windsh ield washer system . . . . . . . . . . . . 208
Anti -lock braking system
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 16
Anti-Lock Braking System . . . . . . . . . . . . . . 120
Anti-s lip regulat ion
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 16
Anti-Slip Regulation . . . . . . . . . . . . . . . . . . . 120
Armrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
263