2017 Acura NSX lights

130 || 131
DRIVINGDRIVING
Starting to Drive
The keyless access system allows simple push-button start.
n
Before Starting the Engine
Check

that the parking brake is applied (pull up on the switch
and look for the indicator light), then depress the brake pedal.
Keep your foot firmly on the brake pedal when starting the
engine.
The engine will be harder to start in cold weather and in
thinner air found at altitudes above 8,000 feet (2,400
m). When starting the engine in cold weather, turn off all
electrical accessories such as the lights, climate control
system, and rear defogger in order to reduce battery drain.
The vehicle will not start if the High Voltage battery
temperature drops below -4F (-20C). Plan your driving and
storage appropriately if you expect this to happen.
Brake pedal
n Changing the Power Mode
Accessory
or On mode: Press the ENGINE START/STOP
button once without pressing the accelerator pedal for
Accessory mode. Press it again for On mode.
Starting the power system: Make sure the parking brake
is applied. Then, press the brake pedal while you press
the ENGINE START/STOP button once. Do not press the
accelerator.
•
When IDS is in QUIET mode: Whether the engine starts
depends on the

engine temperature and the charge in the
High Voltage batteries.
•
When IDS is in SPORT mode: The engine

will start.
Turning the power system off: Select Park (P), then press
the ENGINE START/STOP button.

158 || 159
HANDLING THE UNEXPECTEDHANDLING THE UNEXPECTED
Jump Starting
Turn off the power to electric devices, such as audio and lights. Turn off the power system, then
open the hood.
1.
Remove

the maintenance cover (see page 183), then slide
the terminal cover on your 12-volt battery’s (+) terminal
2.
Connect the first jumper

cable to your vehicle’s 12-volt
battery (+) terminal.
3.
Connect the other end of the first

jumper cable to the
booster battery (+) terminal. Use a 12-volt booster battery
only.
4.
Connect the second jumper cable to

the booster battery (-)
terminal.
5.
Connect the other end of the second

jumper cable to the
front frame (as shown). Do not connect this jumper cable to
any other part.
Booster Battery
Terminal Cover
A battery can explode if you do not follow the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking materials away from the battery.
WARNING
n After the Engine Starts
Once your
vehicle’s engine has started, remove the jumper cables in the following order:
1.
Disconnect the jumper cable from

your vehicle’s ground.
2.
Disconnect the other end of the jumper cable

from the assisting vehicle’s (-) terminal.
3.
Disconnect the jumper cable from

the assisting vehicle’s (+) terminal.
4.
Disconnect the other end of the jumper cable

from your vehicle’s (+) terminal.
Have your vehicle inspected by a nearby service station or an authorized Acura NSX
dealer.
If your vehicle is connected to another vehicle, start the assisting vehicle’s engine and increase
its rpm slightly.
Attempt to start your vehicle’s engine. If it turns over slowly, make sure the jumper cables have
good metal-to-metal contact.
WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash your hands after handling.

160 || 161
HANDLING THE UNEXPECTEDHANDLING THE UNEXPECTED
Overheating
If the temperature gauge needle is at the H mark, the engine suddenly loses power, or steam or
spray comes out from under the hatch, your engine is overheating.
Immediately park the vehicle in a safe place. Turn off all accessories and turn on the hazard
warning lights. Change the gear position to (P).
If no steam or spray is present: Keep the power system on and open the hatch.
If steam or spray is present: Turn off the power system and wait until it subsides. Then, open
the hatch.
Check that the cooling fan is operating and turn the power system off once the temperature
gauge needle comes down. If the cooling fan is not operating, immediately turn the power
system off.
Once the engine has cooled down, inspect the coolant level and
check the cooling system components for leaks. If the coolant
level in the reserve tank is low, or no coolant is in the tank, check
that the radiator is cool. Cover the reserve tank cap with a heavy
cloth and open the cap. Add coolant until it reaches the MAX
mark, and put the cap back on.
Reserve TankMAXMIN
Once the engine has cooled sufficiently, turn the power system on and check the temperature
gauge. If the temperature needle has gone down, resume driving. If it has not gone down,
contact an authorized Acura NSX dealer for repairs.
Steam and spray from an overheated engine can seriously scald you.
Do not open the hatch if steam is coming out.
WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
WARNING
Continuing to drive with the temperature gauge needle at the H mark may damage the engine.
NOTICE

166 || 167
HANDLING THE UNEXPECTEDHANDLING THE UNEXPECTED
Tire Repair Kit
If a tire has a small puncture, you can use the tire repair kit to temporarily repair it. The puncture
must be smaller than 3/16-inch (4 mm) and not in the tire sidewall. Go to a authorized Acura
NSX dealer to have the full-size tire permanently repaired or replaced.
n
Before Repairing

the Tire
•
Park the v

ehicle on a firm, level, and non-slippery surface.
•
Make sure the

vehicle is in Park (P), and apply the parking brake.
•
Turn on the hazard warning

lights, and turn the power system off. n
Getting Ready to R

epair the Tire
1. Open the hatch.
2.
Loosen the tool box tie-downs and

remove the tool box
lid.
3.
Take the kit out of the tool

box.
4.
Place the kit face up on

flat ground near the punctured
tire and away from traffic. Do not place the kit on its side.
Follow the instructions in the kit to repair the tire.Lid Tie Down
Tire Repair Kit
Do not use an unapproved puncture-repairing agent other than the one provided in the kit
that came with your vehicle. If a different agent is used, you may permanently damage the
tire pressure sensor.
NOTICE

168 || 169
HANDLING THE UNEXPECTEDHANDLING THE UNEXPECTED
Fuse Locations
If any electrical devices are not working, set the power mode to VEHICLE OFF (LOCK) and check
to see if any applicable fuse is blown. Fuse locations are shown on the fuse box cover. Locate the
fuse by the fuse number and box cover number.
n
Hood Fuse Box A
Located near the

radiator. Push the tabs to open the box.
Fuses shown on next page.
Circuit Protected Amps
1
70A50A40A20A30A200A
2(50 A) 60 A
(6 0A )
(5 0A )
30 A
30 A
(4 0A )
30 A
30 A
3
(40A )30A(30 A)30A
4 (30 A)10
A
57.5A
610 A
77.5ALeft Headlight High Beam VFP2EPS
Cooling Fan
ABS/VSA Motor ABS/VSA FS R
AS F/B Main Main Fuse
F/B Main 1


Left Electric Parking Brake Motor
Right Electric Parking Brake Motor

Heater Motor 2
Heater Motor 1
E-OP
ADS
AMP
*
Parking Light IGPS PCS 8
Left Headlight Low Beam 10 A
9Right Headlight High Beam
10 10
A
Right Headlight Low Beam10 A
11IGPS Fan 7.5 A
12 FI Main15A
13FI Sub14 20
A
Back Up7.5A
15SBW ECU16 7.5 A
DBW 115A
17IG Coil15 A
18 DBW215A
19Parking Light & Headlight Main 20
A
20 Rear Defroste r
20A
21Front Washer 20A
22 ISC15A
23
24 ACC/IG2 Main 10 A
2510 A
26 Daytime Running Lights
Horn10A
27Interior Lights 7.5 A
28 IGP215A
29Audio10 A
AmpsCircuit Protecte dCircuit Protected Amps
1
70A50A40A20A30A200A
2(50 A) 60 A
(6 0A )
(5 0A )
30 A
30 A
(4 0A )
30 A
30 A
3
(40A )30A(30 A)30A
4 (30 A)10
A
57.5A
610 A
77.5ALeft Headlight High Beam VFP2EPS
Cooling Fan
ABS/VSA Motor ABS/VSA FS R
AS F/B Main Main Fuse
F/B Main 1


Left Electric Parking Brake Motor
Right Electric Parking Brake Motor

Heater Motor 2
Heater Motor 1
E-OP
ADS
AMP
*
Parking Light IGPS PCS 8
Left Headlight Low Beam 10 A
9Right Headlight High Beam
10 10
A
Right Headlight Low Beam10 A
11IGPS Fan 7.5 A
12 FI Main15A
13FI Sub14 20
A
Back Up7.5A
15SBW ECU16 7.5 A
DBW 115A
17IG Coil15 A
18 DBW215A
19Parking Light & Headlight Main 20
A
20 Rear Defroste r
20A
21Front Washer 20A
22 ISC15A
23
24 ACC/IG2 Main 10 A
2510 A
26 Daytime Running Lights
Horn10A
27Interior Lights 7.5 A
28 IGP215A
29Audio10 A
AmpsCircuit Protecte d

170 || 171
HANDLING THE UNEXPECTEDHANDLING THE UNEXPECTED
n Hood Fuse Box B
Located near the 12-volt battery
. Remove the maintenance cover, then push the tabs to
open the box.
AmpsCircuit Protected
160 A60A30A30A30A30A40A
230 A
320 A
47. 5A
5
6 7.
5A20 A
7
8 7.
5A10 A
9
107. 5A
11
12 7.
5A
13
14
15
16
1710A
SBW

F/B Main 2
Wiper
Passenger Power Window IG Main1
Driver Power Window ESB
IG Main2
IMA Moto r
BM S
Stop
Turbo W/ G
Hazard WA/
C/ P

AEV
FI-ECU Backup




IMA Motor
n Driver’s Side Fuse Box
Located under the dashboard.
Circuit Protected Amps110A
215 A
37.5 A
4
520 A
6
20 A
715 A
87.5 A
97.5 A
1010 A
1110 A
121310 A
147.5 A
15
(20A )
16
(7.5 A)
17(20A )
1810 A
19
207.5 A
21
7.5 A
227.5 A
237.5 A
Passenger’s Door Handle Door LockSMART
Front Accessory Power Socket
Fuel Pum p
MISS SO L
ENG
VSA/ABS SRS
Power System 2

Power System 1
Fuel Lid
Driver’s Power Seat Reclining *

Seat Heater *
Driver’s Door Handle
Passenger’s Side Door Unlock
Daytime Running Lights
Key Lock
Air Conditionin g
24Feed Back IG1a 7.5A
25Instrument Panel Lights7.5A
26Power Lumbar Support *(7.5
A)
27Parking Lights7.5A
28Sub Main15 A29Meter10 A30DR27.5A
31Sub Fuel Pump15 A
32SR S10 A
33Passenger’s Side Door Lock 7.5A34Driver’s Door Lock7.5A
35Driver’s Door Unlock7.5A
36Driver’s Power Seat Sliding *(2
0A )
37
7.5A
Right Daytime Running
Light
38
7.5A39 Left Daytime Running LightFeed Back IG1b7.5A
40ACC7.5A
4142
AmpsCircuit Protecte d
Fuse Label
Circuit Protected Amps110A
215 A
37.5 A
4
520 A
6
20 A
715 A
87.5 A
97.5 A
1010 A
1110 A
121310 A
147.5 A
15
(20A )
16
(7.5 A)
17(20A )
1810 A
19
207.5 A
21
7.5 A
227.5 A
237.5 A
Passenger’s Door Handle Door LockSMART
Front Accessory Power Socket
Fuel Pum p
MISS SO L
ENG
VSA/ABS SRS
Power System 2

Power System 1
Fuel Lid
Driver’s Power Seat Reclining *

Seat Heater *
Driver’s Door Handle
Passenger’s Side Door Unlock
Daytime Running Lights
Key Lock
Air Conditionin g
24Feed Back IG1a 7.5A
25Instrument Panel Lights7.5A
26Power Lumbar Support *(7.5
A)
27Parking Lights7.5A
28Sub Main15 A29Meter10 A30DR27.5A
31Sub Fuel Pump15 A
32SR S10 A
33Passenger’s Side Door Lock 7.5A34Driver’s Door Lock7.5A
35Driver’s Door Unlock7.5A
36Driver’s Power Seat Sliding *(2
0A )
37
7.5A
Right Daytime Running
Light
38
7.5A39 Left Daytime Running LightFeed Back IG1b7.5A
40ACC7.5A
4142
AmpsCircuit Protecte d
*if equipped

174 || 175
MAINTENANCEHANDLING THE UNEXPECTED
n Inspecting and Changing Fuses
Set the power mode to
VEHICLE OFF (LOCK). Turn off the
headlights and all accessories.
Remove the fuse box cover.
Check the large fuse in the hood.
If the fuse is blown, use a Phillips-head screwdriver to remove
the screws and replace the fuse with a new one. Reinstall the
screws.
Inspect the small fuses in the hood and the vehicle interior.
If there is a burned out fuse, remove it with the fuse puller and
replace it with a new one.
Blown fuse
Combined fuse
Fuse puller
Replacing a fuse with one that has a higher rating greatly increases the chances of damaging
the electrical system.
NOTICE
MAINTENANCE
Learn about basic maintenance that you can perform on the vehicle yourself, as well as
information about how to best maintain the vehicle.
Safety Precautions
Some of the most important safety precautions are listed below; however, we cannot warn you
of every conceivable hazard that can arise in performing maintenance. Only you can decide
whether or not you should perform a given task.
n
Maintenance Safety
To reduce the possibility
of fire or explosion, keep cigarettes, sparks, and flames away from
the battery and all fuel-related parts.
Never leave rags, towels, or other flammable objects in the engine compartment.
To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.
Wear eye protection and protective clothing when working with the battery or compressed
air.
Do not run the engine in confined spaces where carbon monoxide gas can accumulate.
n
Vehicle Safety
The vehicle must be stationary

, and parked on level ground with the parking brake set and
the engine off.
Be aware that hot parts can burn you.
Be aware that moving parts can injure you.

208 || 209
SPECIFICATIONSMAINTENANCE
• If possible, remove the vehicle from the garage or enclosed area, remove covering, and
periodically run the engine until it reaches full operating temperature (the cooling fan cycles
on and off twice). Preferably, do this once a month.
•
To maintain the High V

oltage battery, drive your vehicle for more than 30 minutes at least
once every three months.
If road conditions are not suitable or desirable for driving, the following alternate procedure can
be used to maintain the vehicle’s High Voltage battery if local laws permit idling:
1.
Remove

the vehicle from the garage or enclosed area to prevent carbon monoxide
accumulation.
2.
Depress the brake pedal and pr

ess the ENGINE START/STOP button as you normally would
to start the vehicle.
3.
Allow the vehicle

to run for 30 minutes. Time spent at idle stop still counts as part of this
30-minute run.
Paint Care
Your vehicle’s paint requires up to 60 days from the production date to fully cure. During this
time, avoid applying any wax or paint sealant-type products, as they could hinder the curing
process and affect the paint’s durability.
You may polish the paint during these 60 days if the polishes do not contain any wax or paint
sealant ingredients. Use only clean, high-quality microfiber towels or pads, as they are softer
material and have less chance of scratching the finish. It is absolutely necessary to keep the
microfiber towels or pads properly cleaned and maintained before using on your vehicle.
For more information, contact an authorized Acura NSX dealer. n
Vehicle
ModelAcura NSX
No. of Passengers :
Front 2
Weights:Gross Vehicle
Weight RatingU.S. :4,497 lbs (2,040 kg)Canada :2,040 kgGross Axle Weight
Rating (Front)U.S.:1 ,885 lbs (855 kg)Canada :855 kgGross Axle Weight
Rating (Rear)U.S.:2,646 lbs (1,200 kg)Canada :1,200kg
Air Conditioning:
Refrigerant Type
Charge Quantit y
Lubricant Type
HFC-134a (R-134a) 16.0 - 17.8 oz (455 - 505 g)
ND-OIL 11
Quantity3.72 - 4.23 oz (110 - 125 mL)
n Engine
Fuel
Engine Specification sDisplacement 213 cu-in (3,493 cm3)
NG K
Spark PlugsSILZKAR8F7S
Unleaded premium gasoline,
Type
pump octane number of 91 or higher
Fuel Tank Capacity 15.6 US gal (59 ℓ)
n Light Bulbs
LE DLEDLEDLED
LED
LEDLEDLEDLEDLEDLEDLEDLED
LEDLEDLEDLEDLED
Map Lights
Ambient Lights
Door Courtesy Lights
Glove Box Ligh t
Trunk Light
Headlights (Low Beam )Headlights (High Beam )
Front Turn Signal/Parking Lights
Front Side Marker Lights
Side Turn Signal Lights
(on Door Mirrors)
Daytime Running Lights
Rear Turn Signal Lights
Brake/Taillights
Rear Side Marker Lights
Taillights
Back-Up Lights
Rear License Plate Lights
High-M ount Brake Ligh t
In terior Lights
SPECIFICATIONS