2017 Acura MDX belt

18 |
S
AFETY
Installing a LATCH-Compatible Child Seat
A LATCH-compatible child seat can be installed in either of the two outer-rear
seats. A child seat is attached to the lower anchors with either the rigid or flexible
type of connectors.
1.
Locate the lower anchors under the marks.
2.
Place the child seat on the

vehicle seat, then
attach the child seat to the lower anchors
according to the instructions that came with
the child seat. Make sure that the lower anchors
are not obstructed by the seat belt or any other
object.
Marks
Lower anchors Rigid type
Flexible type
Marks
With second-row bench seat
With second-row captain seats

| 19
S
AFETY
Outer seats: Raise the head r
estraint to its

highest position, then route
the tether strap


between the head restraint legs, and secur

e the


tether strap hook onto the anchor

.
Center seat:

Lower the center head restraint to


its lowest position, then route

the tether strap


over the top of the

head restraint and secure the


tether strap hook onto the anchor

.
3.
Make sure

the strap is not twisted. Tighten
the tether strap as instructed by the child seat
manufacturer.
4.
Make sure

the child seat is firmly secured by
rocking it forward and back and side to side;
little movement should be felt.
5.
Make sure an

y unused seat belt that a child
can reach is buckled, the lockable retractor is
activated, and the belt is fully retracted and
locked.
Anchor
Tether Strap Hook
With second-row captain seats
With second-row bench seat
Anchor
Tether strap hook

20 |
S
AFETY
Installing a Child Seat with a Lap/Shoulder Seat Belt
1.
Place the child seat on the
vehicle seat.
2.
Route the seat

belt through the child
seat according to the seat manufacturer’s
instructions, and insert the latch plate into the
buckle. Insert the latch plate fully until it clicks.
3.
Slowly pull the shoulder part

of the belt all the
way out until it stops. This activates the lockable
retractor.
4.
Let the seat belt completely

wind up into the
retractor, then try to pull it out to make sure
the retractor is locked. If you are able to pull the
shoulder belt out, the lockable retractor is not
activated. Pull the seat belt all the way out, and
repeat steps 3 – 4.
5.
Grab the shoulder part of

the seat belt near the
buckle, and pull up to remove any slack from the
lap part of the belt. When doing this, place your
weight on the child seat and push it into the
vehicle seat.
6.
Make sure

the child seat is firmly secured by
rocking it forward and back and side to side;
little movement should be felt.
7.
Make sure an

y unused seat belt that a child
can reach is buckled, the lockable retractor is
activated, and the belt is fully retracted and
locked.
To deactivate a lockable retractor, release the buckle and allow the seat belt to
wind up all the way.

| 21
S
AFETY

Adding Security with a Tether
A tether anchorage point is provided behind each second- and third-row seating
position. A child seat that is installed with a seat belt and comes with a tether
can use the tether for additional security.
Second-row seats
1.
Outer seats: Raise the head r

estraint to its
highest position, then route the tether strap
through the head restraint legs.
1.
Center seat:

Lower the head restraint to its
lowest position, then route the tether strap over
the top of the head restraint.
2.
Make sure

the strap is not twisted, and secure
the tether strap hook onto the anchor.
3.
Tighten the tether strap as instructed b

y the
child seat manufacturer.
Second row seatTether anchorage points
Second row seat
Anchor Tether strap hook
Tether Anchorage Points
With second-row bench seat
With second-row captain seats
Anchor
Tether Strap Hook
With second-row bench seat
With second-row captain seats

| 23
S
AFETY
Allowing a child age 12 or under to sit in the front can result in injury or
death if the passenger’s front airbag inflates.
If a larger child must ride in front, move the vehicle seat as far to the rear as
possible, have the child sit up properly and wear the seat belt properly, using
a booster seat if needed.
WARNING
Protecting Larger Children
When a child is too big for a child seat, secure the child in a rear seat using the
lap/shoulder seat belt.
Have the child sit upright and all the way back, then ensure the following:
•
The child’s knees bend comfortably

over the edge
of the seat.
•
The shoulder belt crosses between the child’

s
neck and arm.
•
The lap part of the seat belt is as low as possible,
touching the

child’s thighs.
•
The child can stay seated for the

whole trip.
If a lap/shoulder belt cannot be used properly, position the child in a booster seat
in a rear seating position. For the child’s safety, check that the child meets the
booster seat manufacturer’s recommendations.
Some U.S. states and Canadian provinces/territories require children to use a
booster seat until they reach a given age or weight (e.g., 6 years or 60 lbs). Be
sure to check current laws in the state or province/territory where you intend to
drive.

| 27
I
NSTRUMENT PANEL
Supplemental Restraint System (SRS)
There is a problem with one of the airbag systems or seat belt tensioners.
Speed-Sensitive Electric Power Steering (EPS)
There is a problem with the electric power steering system. Stop in a safe
place and restart the engine.
Tire Pressure Monitoring System (TPMS)
(Blinks and stays on) There is a problem with the tire pressure monitoring
system, or a spare tire* is installed.
Keyless Access system
There is a problem with the keyless access system.
Vehicle Stability Assist (VSA®) system
There is a problem with the VSA system or the hill start assist system.
Brake system
There is a problem with one of the braking systems. Avoid high speeds and
sudden braking. Your vehicle still has normal braking ability.
Super-Handling All-Wheel Drive™ (SH-AWD®)*
•
There is a problem

with the SH-AWD system.
•
(Blinks) Stop in a safe place, change the gear

to Park, and idle until the
indicator goes off.
Blind Spot Information (BSI)*
There is a problem with the BSI system or the sensor is blocked.
Electric Parking Brake system
There is a problem with the system. Have your vehicle checked by a dealer.
Collision Mitigation Braking System
TM (CMBSTM)
There is a problem with the system, the temperature is too high, or the
camera is blocked.
Lane Departure Warning (LDW)
Road Departure Mitigation (RDM)
There is a problem with the system, the temperature is too high, or the
camera is blocked.
Auto idle stop*
There is a problem with the auto idle stop system.
Immobilizer/security system
Your key or remote transmitter cannot be recognized by the vehicle. If the indicator
blinks, you may not be able to start the engine. Turn the vehicle off, press and
hold the brake pedal, and restart the vehicle. If it continues to blink, there may
be a problem with the system. See your dealer. Canadian models: To reset the
immobilizer system, follow the steps above after the battery has been disconnected.
Ca nada
U.S.SYSTEM
U.S.
Canada
*if equipped

28 |
I
NSTRUMENT PANEL
Condition Indicators
These indicators may require you to perform an action.
Parking brake
Release the parking brake before driving.
Seat belt reminder
Make sure seat belts are fastened for you and all passengers. The indicator
blinks and beeps sound continuously if you or your front passenger has not
fastened your seat belts when you begin driving. If the indicator remains on
after seat belts are fastened, see your dealer.
Low fuel
Refuel as soon as possible. If the indicator blinks, there is a problem with
the fuel gauge. See your dealer.
Low tire pressure
Stop in a safe place, check tire pressures, and inflate tire(s) if necessary.
Blinks for a minute then remains lit: the spare tire is fitted. Otherwise, there
is a problem with the TPMS system. See your dealer.
System message
When a condition or malfunction indicator comes on, a message also
appears on the multi-information display. Check the display for more
information.
Immobilizer
Your remote transmitter cannot be recognized by the vehicle. If the
indicator blinks, you may not be able to start the engine. Turn the vehicle
off, and then on again. If it continues to blink, there may be a problem with
the system. See your dealer.
U.S.
Canada

| 49
V
EHICLE CONTROLS
Folding Down the
Second-Row Seats
Separately fold down the left and right halves of the second-row seat to make
room for cargo.
Models with second-row bench seat
1.
Store the center seat belt b

y inserting the latch
plate into the slot on the side of the anchor
buckle.
2.
Retract the seat

belt into the holder on the
ceiling.
3.
Lower the center head restraint

to its lowest
position. Put the armrest back into the seat-
back.
All models
4.
Pull up the seat-back angle adjustment lev

er.
To return the seat to its original position, pull up the seat-back to an upright
position until it is securely latched into place. Reposition the seat belts as
necessary.
Folding Down the Third-Row Seats
Separately fold down the left and right halves of
the third-row seat to make room for cargo.
1.
Pull the handle on the seat

-back. The head
restraint folds down.
2.
Push the seat-back

forward while pulling the
handle.
To return the seat to its original position, pull up
the seat-back while pulling up the handle. Push the
head restraint up to its original position.
Lever
Handle
Accessing the Third-Row Seats
Press the button on the second-row seat back
or outer seat side. The second-row seat slides
forward to allow easy access to the third row.
The button is inoperable when the vehicle is
moving.