2016 YAMAHA XENTER 125 stop start

Instrument and control functions
3-6
1
234
5
6
7
8
9
10
11
12
TIP
If the ambient temperature falls be-
low –10 C, a lower temperature
than –10 C will not be displayed.

If the ambient temperature climbs
above 40  C, a higher temperature
than 40 C will not be displayed.

The accuracy of the temperature
reading may be affected when rid-
ing slowly (approximately under 20
km/h (12 mi/h)) or when stopped at
traffic signals, railroad crossings,etc.
Clock
To set the clock:
1. Push the “SELECT” button and “RESET” button together for at
least two seconds.
2. When the hour digits start flashing, push the “RESET” button to set the
hours.
3. Push the “SELECT” button, and the minute digits will start flashing.
4. Push the “RESET” button to set the minute digits.
5. Push the “SELECT” button and then release it to start the clock.
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear to-
wards “E” (Empty) as the fuel level
decreases. When the bottom segment
of the fuel meter and fuel level warning
indicator “*” starts flashing, refuel as
soon as possible. When the key is
turned to “ON”, all of the display seg-
ments of the fuel meter will appear for a
few seconds, and then shows the actu-
al fuel level.
Brightness control mode
This function allows you to adjust the
brightness of the speedometer panel to
suit the outside lighting conditions.
To set the brightness
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” but- ton.
3. Turn the key to “ON”, and then re- lease the “SELECT” button after
five seconds. The display will
change to brightness control mode.
4. Push the “RESET” button to select the desired brightness level in the
following order: BL-01  BL-02 
BL-03  BL-04  BL-05 
BL-01.
5. Turn the key to “OFF”.
U53BE1E0 6 ページ ２０１５年９月１５日　火曜日　午後１時４８分

5-1
1
2
3
45
6
7
8
9
10
11
12
Operation and important riding points
EAU15952
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10272
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accidentor injury.
EAU45311
TIPThis model is equipped with a lean an-
gle sensor to stop the engine in case of
a turnover. To start the engine after a
turnover, be sure to turn the main
switch to “OFF” and then to “ON”. Fail-
ing to do so will prevent the engine from
starting even though the engine willcrank when pushing the start switch.
EAUT3682
Starting the engineNOTICE
ECA10251
See page 5-3 for engine break-in in-
structions prior to operating the ve-hicle for the first time. 1. Turn the key to “ON”. The engine trouble warning light
and coolant temperature warning
light should come on for a few sec-
onds, then go off. NOTICE: If a
warning light does not go off,
have a Yamaha dealer check its
electrical circuit.
[ECAT1171]
2. Close the throttle completely.
3. Start the engine by pushing the start switch while applying the front
or rear brake. NOTICE: For maxi-
mum engine life, never acceler-
ate hard when the engine is
cold!
[ECAT1310]
If the engine does not start, re-
lease the start switch, wait a few
seconds, and then try again. Each
starting attempt should be as short
as possible to preserve the bat-
tery. Do not crank the engine more
U53BE1E0 1 ページ ２０１５年９月１５日　火曜日　午後１時４８分

Periodic maintenance and adjustment
6-13
1
2
3
4
56
7
8
9
10
11
12 spring, O-ring and engine oil drain
bolt B.
TIPMake sure that the O-ring is properlyseated.
7. Install engine oil drain bolt A, and then tighten both drain bolts to
their specified torques.
8. Refill with the specified amount of the recommended engine oil, and
then install and tighten the oil filler
cap.NOTICE
ECA11671

Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

Be sure no foreign material en-ters the crankcase.
9. Start the engine, and then let it idle for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
10. Turn the engine off, and then check the oil level and correct it if
necessary.
To reset the oil change indicator
and oil change tripmeter
TIPThe oil change indicator and oil change
tripmeter can be reset when "OIL
CHANGE" and "OIL TRIP" appear in
the multi-function display. (Seepage 3-3.)
EAU20067
Final transmission oilThe final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart. 1. Start the engine, warm up the final transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the center- stand.
3. Place an oil pan under the final transmission case to collect the
used oil.
4. Remove the final transmission oil filler cap and its O-ring from the fi-
nal transmission case.
Tightening torque:Engine oil drain bolt A: 20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Engine oil drain bolt B:
32 Nm (3.2 m·kgf, 23.1 ft·lbf)
Recommended engine oil: See page 8-1.
Oil change quantity:
1.10 L (1.16 US qt, 0.97 Imp.qt)
U53BE1E0 13 ページ ２０１５年９月１５日　火曜日　午後１時４８分

Periodic maintenance and adjustment6-34
1
2
3
4
567
8
9
10
11
12
Engine overheating
WARNING
EWAT1041

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-
tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the capwhile turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily
used instead, provided that it is changed to the recommended coolantas soon as possible.Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U53BE1E0 34 ページ ２０１５年９月１５日　火曜日　午後１時４８分