2016 YAMAHA VIKING VI fuse

Checking the front and rear brake pads.................................................. 8-36
Checking the parking brake pads ...... 8-37
Checking the brake fluid level ............ 8-37
Brake fluid replacement ..................... 8-39
Checking the brake pedal .................. 8-39
Parking brake lever free play adjustment........................................ 8-39
Brake light switch adjustment ............ 8-41
Cable inspection and lubrication........ 8-41
Brake pedal and accelerator pedal lubrication ......................................... 8-41
Checking the stabilizer bushes .......... 8-42
Rear knuckle upper and lower pivot
lubrication (left and right) .................. 8-42
Steering shaft lubrication ................... 8-43
Wheel removal.................................... 8-43
Tire replacement ................................ 8-44
Wheel installation ............................... 8-45
Battery ................................................ 8-45
Jump-starting ..................................... 8-49
Fuse replacement............................... 8-50
Replacing a headlight bulb................. 8-53 Headlight beam adjustment ...............8-55
Tail/brake light bulb replacement .......8-56
Troubleshooting ..................................8-57
Troubleshooting charts .......................8-59
CLEANING AND STORAGE ....................9-1 Cleaning................................................9-1
Storage .................................................9-2
SPECIFICATIONS..................................10-1
CONSUMER INFORMATION ................11-1 Identification number records.............11-1
INDEX ....................................................12-1
UB857AE0.book Page 3 Monday, August 24, 2015 8:59 AM

3-2
3
EBU31190Right view
11 109
9856 7
44
33
2
1
1. Tail/brake light
2. Engine oil dipstick
3. Passenger seat belt
4. Passenger seat
5. Battery
6. Fuses
7. Headlight
8. Coolant reservoir
9. Storage compartment
10.Fuel tank cap
11.Oil filter cartridgeUB857AE0.book Page 2 Monday, August 24, 2015 8:59 AM

4-26
4
NOTICEECB02110The combined load of the accessories
connected to the front and rear auxiliary
DC jacks must never exceed the stated
maximum capacity. Exceeding the maxi-
mum capacity may overload the circuit
and cause the fuse to blow.
 If accessories are used without the en-
gine running, the battery may discharge.
 Do not use an automotive cigarette light-
er or other accessories with a plug that
gets hot, because the jack can be dam-
aged. To use an auxiliary DC jack1. Set the light switch to “ ”.
2. Turn the accessory off.
3. Start the engine. (See page 6-2.)
4. Open the auxiliary DC jack cap, and then
insert the accessory power plug into the
jack.
1. Auxiliary DC jack cap
2. Front auxiliary DC jack
1. Auxiliary DC jack cap
2. Rear auxiliary DC jack
2
1
21
UB857AE0.book Page 26 Monday, August 24, 2015 8:59 AM

8-50
8
4. Connect the negative lead of the jumpercable to the negative terminal of the
charged battery and the other end of the
negative lead to an unpainted metal sur-
face of the frame of the vehicle to be
started.
5. Start the engine. (Refer to “Starting the engine” on page 6-2.)
6. After the engine starts, disconnect the
negative lead of the jumper cable from
the frame and charged battery, and then disconnect the positive lead of the jump-
er cable from the charged battery and the
battery in the vehicle.
7. Install the hood.
EBU33100Fuse replacementThe main fuse, the fuel injection system fuse,
the EPS fuse, and the fuse box are located
under the hood. (See page 8-10 for hood re-
moval and installation procedures.)
1. Jumper cable negative lead
1
UB857AE0.book Page 50 Monday, August 24, 2015 8:59 AM

8-51
8
If a fuse is blown, replace it as follows.1. Turn the key to “ ” (off) and turn off the
electrical circuit in question.
1. Fuse box
2. Main fuse
3. EPS fuse
4. Fuel injection system fuse
5. Fuel injection system spare fuse
1 3
2
4
5
1. Backup fuse “BACK UP” (for clock)
2. Ignition fuse “IGNITION”
3. Four-wheel-drive motor fuse “DIFF”
4. Auxiliary DC jack fuse “TERMINAL”
5. Signaling system fuse “SIGNAL”
6. Headlight fuse “HEAD”
7. Spare fuse
8. Radiator fan motor fuse “FAN”
1
2
3
4
5
6
8
7
7
UB857AE0.book Page 51 Monday, August 24, 2015 8:59 AM

8-52
8
NOTICEECB00641To prevent accidental short-circuiting,
turn off the main switch when checking or
replacing a fuse. 2. Remove the hood. (See page 8-10 forhood removal and installation proce-
dures.)
3. Remove the blown fuse, and then install a new fuse of the specified amperage.
WARNING! Always use a fuse of the specified amperage. Never use any
material in place of the proper fuse.
Using an improper fuse can cause
damage to the electrical system and
may lead to a fire.
[EWB03440]
Specified fuses: Main fuse:40.0 A
Fuel injection system fuse: 10.0 A
Headlight fuse: 15.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Signaling system fuse: 10.0 A
Four-wheel-drive motor fuse: 10.0 A
Radiator fan motor fuse: 25.0 A
Backup fuse: 10.0 A
EPS fuse: 40.0 A
UB857AE0.book Page 52 Monday, August 24, 2015 8:59 AM

8-53
8
4. Turn the key to “ ” (on) and turn on theelectrical circuit in question to check if
the device operates. If the fuse blows
again immediately, have a Yamaha dealer
check the electrical system.
5. Install the hood.EBU32670Replacing a headlight bulbIf a headlight bulb burns out, replace it as fol-
lows.
1. Remove the cover at the rear of the head- light by pulling it off. 2. Remove the headlight bulb cover by pull-
ing it off.
3. Disconnect the headlight coupler.1. Cover at the rear of the headlight
1
1. Headlight bulb cover
1
UB857AE0.book Page 53 Monday, August 24, 2015 8:59 AM

10-5
10
High-range indicator light:LED
Low-range indicator light: LED
Differential gear lock indicator light:
LED
EPS warning light: LED
Helmet/Seat belt indicator light: 14 V, 0.85 W × 2Fuses:Main fuse:
40.0 A
Fuel injection system fuse: 10.0 A
EPS fuse:
40.0 A
Headlight fuse: 15.0 A
Signaling system fuse: 10.0 A
Ignition fuse:
10.0 A
Auxiliary DC jack fuse: 10.0 A
Backup fuse: 10.0 A
Four-wheel-drive motor fuse:
10.0 A
Radiator fan motor fuse: 25.0 A
EBU33220For Europe only
The figures quoted are emission levels and
are not necessarily safe working levels. Whilst
there is a correlation between the emission
and exposure levels, this cannot be used reli-
ably to determine whether or not further pre-
cautions are required. Factors that influence
the actual level of exposure of work-force in-
clude the characteristics of the work room,
the other sources of noise, etc. i.e. the num-
ber of machines and other adjacent process-
es, and the length of time for which an
operator is exposed to the noise. Also the
permissible exposure level can vary from
country. This information, however, will en-
able the user of the machine to make a better
evaluation of the hazard and risk.
UB857AE0.book Page 5 Monday, August 24, 2015 8:59 AM