2016 YAMAHA TT-R50E lock

Instrument and control functions
4-2
4
EAU39865
Spee d limiter
Your motorcycle is equipped with an
adjustable speed limiter. The speed
limiter keeps the throttle from fully
opening, even when the throttle grip is
turned to the maximum.
1. Loosen the locknut.
2. To increase the maximum engine power available and the maximum
speed of the motorcycle, turn the
adjusting screw in direction (a). To
decrease the maximum engine
power available and the maximum
speed of the motorcycle, turn the
adjusting screw in direction (b).
3. Tighten the locknut.
WARNING
EWA14404
Improper a djustment of the spee d
limiter coul d cause improper throttle
operation. You coul d lose control,
have an acci dent or be injure d. Do
not turn the a djustin g screw out
more than 28 mm (1.1 in). Always
make sure the throttle g rip free play
is a djuste d to 3.0–5.0 mm (0.12–0.20
in). (See pag e 7-13.)
1. Locknut
2. Adjusting screw
1. No more than 28 mm (1.1 in)
12
(b)
(a)
1
U2CJ83E0.book Page 2 Friday, June 26, 2015 10:36 AM

Instrument and control functions
4-4
4
EAU12944
Brake ped al
The brake pedal is located on the right
side of the motorcycle. To apply the
rear brake, press down on the brake
pedal.
EAU13183
Fuel tank cap
To remove the fuel tank cap, turn it
counterclockwise, and then pull it off.
To install the fuel tank cap, insert it into
the tank opening, and then turn it
clockwise.
WARNING
EWA11092
Make sure that the fuel tank cap is
properly close d after fillin g fuel.
Leakin g fuel is a fire hazar d.
1. Brake pedal
1
1. Fuel tank cap
1
U2CJ83E0.book Page 4 Friday, June 26, 2015 10:36 AM

Instrument and control functions
4-7
4
recommended by Yamaha because it
can cause damage to the fuel system
or vehicle performance problems.
EAU13414
Fuel tank
breather hose
Before operating the motorcycle:
 Check the fuel tank breather hose
connection.
 Check the fuel tank breather hose
for cracks or damage, and replace
it if necessary.
 Make sure that the fuel tank
breather hose is not blocked, and
clean it if necessary.
1. Fuel tank breather hose
U2CJ83E0.book Page 7 Friday, June 26, 2015 10:36 AM

Periodic maintenance an d a djustment
7-16
7
EAU46252
A djustin g the clutch free play
The clutch free play must be checked
and, if necessary, adjusted as follows
at the intervals specified in the periodic
maintenance and lubrication chart.
1. Remove the clutch adjusting screw cover by removing the
screws.
2. Loosen the locknut.
3. Slowly turn the clutch adjusting screw in direction (a) until resis-
tance is felt, and then turn it 1/8
turn in direction (b).
4. Tighten the locknut to the speci- fied torque.
TIP
When tightening the locknut, hold the
clutch adjusting screw with a screw-
driver so that it does not turn together
with the locknut.
5. Install the clutch adjusting screwcover by installing the screws.
1. Screw
2. Clutch adjusting screw cover
1. Locknut
2. Clutch adjusting screw
Tightenin g torque:
Locknut: 6 Nm (0.6 m·kgf, 4.3 ft·lbf)
U2CJ83E0.book Page 16 Friday, June 26, 2015 10:36 AM

Periodic maintenance an d a djustment
7-20
7
EAU22762
Drive chain slack
The drive chain slack should be
checked before each ride and adjusted
if necessary.
EAU22777To check the drive chain slack
1. Place the motorcycle on the side- stand.
TIP
When checking and adjusting the drive
chain slack, there should be no weight
on the motorcycle.
2. Shift the transmission into theneutral position.
3. Measure the drive chain slack as shown.
4. If the drive chain slack is incorrect, adjust it as follows.
EAU40115To a djust the d rive chain slack
Consult a Yamaha dealer before ad-
justing the drive chain slack. 1. Loosen the brake pedal free play adjusting nut, axle nut, and lock-
nut at each end of the swingarm. 2. To tighten the drive chain, turn the
drive chain slack adjusting nut at
each end of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting nut at each end
of the swingarm in direction (b),
and then push the rear wheel for-
ward. NOTICE: Improper drive
chain slack will overloa d the en-
g ine as well as other vital parts
of the motorcycle an d can lead
to chain slippa ge or breakag e.
To prevent this from occurrin g,
keep the d rive chain slack with-
in the specifie d limits.
[ECA10572]
Drive chain slack:
35.0–45.0 mm (1.38–1.77 in)
1. Drive chain slack
1. Brake pedal free play adjusting nut
2. Drive chain slack adjusting nut
3. Locknut
1. Axle nut
2. Drive chain slack adjusting nut
3. Locknut
1
2
3
231
U2CJ83E0.book Page 20 Friday, June 26, 2015 10:36 AM

Periodic maintenance an d a djustment
7-21
7
TIP
Using the alignment marks on each
side of the swingarm, make sure that
both drive chain pullers are in the same
position for proper wheel alignment.
3. Tighten the axle nut and both
locknuts to the specified torques.
4. Adjust the brake pedal free play. (See page 7-18.)
5. Make sure that the drive chain pullers are in the same position,
the drive chain slack is correct,
and the drive chain moves
smoothly.
EAU23018
Cleanin g an d lu bricatin g the
d rive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.
NOTICE
ECA10584
The drive chain must be lu bricate d
after washin g the motorcycle, ri din g
in the rain or ri din g in wet areas.
1. Remove all dirt and mud from the
drive chain with a brush or cloth.
TIP
For a thorough cleaning, have a
Yamaha dealer remove the drive chain and soak it in solvent.
2. Spray Yamaha chain lubricant or other suitable chain lubricant on
the entire chain, making sure that
all side plates and rollers have
been sufficiently oiled.
1. Alignment marks
2. Drive chain puller
3. Drive chain slack adjusting nut
Tightenin g torques:
Axle nut: 60 Nm (6.0 m·kgf, 43 ft·lbf)
Locknut:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
(b)(a)
321
U2CJ83E0.book Page 21 Friday, June 26, 2015 10:36 AM

Periodic maintenance an d a djustment
7-31
7 5. Connect the brake cable to the
brake camshaft lever, and then in-
stall the brake lever free play ad-
justing nut on the brake cable.
TIP
If the spring was removed, install it
onto the brake cable with its smaller di-
ameter end facing down.
6. Adjust the brake lever free play.(See page 7-17.)
7. While applying the front brake, push down hard on the handlebar
several times to check for proper
fork operation.
8. Install each front fork leg guard by installing the bolts.
EAU25081
Rear wheel
EAU56732
To remove the rear wheel
WARNING
EWA10822
To avoi d injury, securely support the
vehicle so there is no dan ger of it
fallin g over.
1. Loosen the axle nut.
2. Remove the brake pedal free play
adjusting nut, and then discon-
nect the brake rod from the brake
camshaft lever.
Tightenin g torque:
Axle nut: 35 Nm (3.5 m·kgf, 25 ft·lbf)
1. Brake cable
2. Spring
1
2
1. Axle nut
2. Washer
3. Drive chain slack adjusting nut
4. Locknut
5. Drive chain puller
1
5
43
2
U2CJ83E0.book Page 31 Friday, June 26, 2015 10:36 AM

Periodic maintenance an d a djustment
7-32
7
3. Fully loosen the locknut and drive
chain slack adjusting nut on each
end of the swingarm.
4. Lift the rear wheel off the ground according to the procedure on
page 7-29.
5. Remove the axle nut, washer and the drive chain puller at the left
side, then pull the wheel axle out
together with the drive chain puller
from the right side.
6. Push the wheel forward, and then remove the drive chain from the
rear sprocket.
TIP
The drive chain does not need to be
disassembled in order to remove and
install the wheel.
7. Remove the wheel.
To install the rear wheel 1. Install the drive chain onto the rear sprocket, lift the rear wheel off the
ground, and then install the wheel
by inserting the wheel axle togeth-
er with the drive chain puller from
the right side.
TIP
Make sure that the slot in the brake
shoe plate fits over the retainer on the
swingarm.
2. Install the drive chain puller at theleft side, washer and axle nut.
1. Brake pedal free play adjusting nut
2. Brake rod
3. Brake camshaft lever
1. Wheel axle
12
3
1
1. Slot
2. Retainer
U2CJ83E0.book Page 32 Friday, June 26, 2015 10:36 AM