2016 TOYOTA LAND CRUISER engine

10
FEATURES/OPERATIONS
Automatic Transmission
* The “ENGINE START STOP” switch must be in “IGNITION ON” mo\
de and the brake pedal depressed to shift from Park.
Shift the shift lever to “S” position from “D” position.
+: Upshift (push and release)

-: Downshift (pull and release)
Downshifting increases power going uphill, or provides engine braking do\
wnhill.
For best fuel economy during normal driving conditions, always drive wit\
h the shift
lever in the “D” position.
“S” (Sequential) mode
Park*
Reverse
Neutral
Drive
P
R
N
D
S“S” mode
Auto lock/unlock
Automatic door locks can be programmed to operate in two different modes\
, or
turned OFF.
-Doors lock when shifting from Park.
-Doors lock when the vehicle speed is approximately 12 mph or higher.
-Doors unlock when shifting into Park.
-Doors unlock when the driver’s door is opened within 45 seconds afte\
r turning the
“ENGINE START STOP” switch OFF.
Refer to the Owner’s Manual for more details.
Power modeSecond start mode
For powerful acceleration and driving in
mountainous regions.For starting on slippery surfaces, such
as snowy roads. Press “2nd” to return to
normal mode.

22
Crawl Control
Multi-terrain Monitor
Speed selection switch
LoHi(1)
(2)
Med
Lo-MedMed-Hi
Speed modes
FEATURES/OPERATIONS
Press “” switch while the engine switch is in IGNITION ON mode to check
vehicle surroundings.
Note: The amount of time that the screen is displayed changes according\
to
the vehicle speed at the time the VIEW switch was pressed. Speeds exceed\
ing
approximately 7 mph (12 km/h) will cancel monitor viewing.
For more details, please refer to the Owner’s Manual.
Crawl Control allows travel on extremely rough off-road surfaces at a fi\
xed low
speed without pressing the accelerator or brake pedal. Operating status \
displays
on the MID.
Lo to Lo-Med - Rock, mogul (downhill) and gravel (downhill)
Lo-Med to Med - Mogul (uphill)
Med-Hi - Snow, mud, gravel (uphill), sand, dirt, mogul (uphill) and grass

26
FEATURES/OPERATIONS
COOLBOX
PWR
Cooler box
Push “PWR” button to turn cooler box ON; indicator will illuminate\
.
Indicator
Power outlets-12V DC
The “ENGINE START STOP” switch must be in “ACCESSORY” or “\
IGNITION ON”
mode to be used.
FrontRear
Parking brake
(2) Push
SetRelease
(1) Pull slightly
(3) Lower
Pull
Cup holders
FrontRear

OVERVIEWFEATURES/OPERATIONS TOYOTA SAFETY SENSESAFETY AND EMERGENCY FEATURES
27
Power outlet-120V AC
The “ENGINE START STOP” switch must be in “IGNITION ON” mode\
to be used.
Qi wireless charger
A portable device can be charged by just placing Qi standard wireless ch\
arge
compatible portable devices according to the Wireless Power Consortium, \
such as
smart phones and mobile batteries, etc., on the charge area.
This function cannot be used with portable devices that are larger than \
the
charging area. Also, depending on the portable device, it may not operat\
e as
normal. Please read the Owner’s Manual for portable devices to be use\
d. The power switch must be in ACCESSORY or ON mode.
(1)
Push to open door.Push power supply charging button.
Note: While device is charging, the light is orange.
The light turns green when it is finished.
Place charging side of device on
the charge area.
(2)
(3)

29
OVERVIEWFEATURES/OPERATIONS TOYOTA SAFETY SENSESAFETY AND EMERGENCY FEATURES

Pre-Collision System (PCS)
The Pre-Collision System uses a radar sensor and camera sensor to help d\
etect
vehicles and pedestrians in front of your vehicle. If the system determi\
nes that
the possibility of a frontal collision with a vehicle or pedestrian is h\
igh, the system
warns the driver to take evasive action while the potential brake pressu\
re is
increased to help the driver avoid collision or reduce the impact to the\
vehicle and
it’s occupants.
Note: PCS is enabled each time the engine switch is turned to Ignition On. Th\
e
system can be disabled/enabled and the warning timing of the system can \
be
changed.
Pre-collision warning
When the system determines that the possibility of a frontal collision i\
s high,
a buzzer will sound and a warning message will be displayed on the Multi\
-
Information Display (MID) to urge the driver to take evasive action.
Pre-collision brake assist
When the system determines that the possibility of a frontal collision i\
s high, the
system applies greater braking force in relation to how strongly the bra\
ke pedal is
depressed.
Pre-collision braking
When the system determines that the possibility of a frontal collision i\
s high, the
system warns the driver. If the system determines that the possibility o\
f a collision
is extremely high, the brakes are automatically applied to help avoid th\
e collision
or reduce the collision speed.

30

Changing the pre-collision warning timing

Disabling the Pre-Collision System (PCS)
Each time the Pre-Collision System switch is pressed, the response to th\
e warning
distance changes as follows:
Far
Middle
Near
To disable the system
Press the PCS switch for 3 seconds or more.
The PCS warning light will turn on and a message will be displayed on th\
e Multi-
Information Display (MID).
To enable the system
Press the PCS switch again.
The system is enabled each time the engine switch is turned to IGNITION \
ON mode.
TOYOTA SAFETY SENSE

31
OVERVIEWFEATURES/OPERATIONS TOYOTA SAFETY SENSESAFETY AND EMERGENCY FEATURES
Monocular camera sensor
Millimeter
wave radar
As part of the Pre-Collision System, this function is also designed to f\
irst provide
an alert and then automatic braking if needed.
Pedestrian Detection Function
The Pre-Collision System also features a pedestrian detection function. \
Using
a millimeter wave radar and monocular camera sensor, this advanced senso\
r
system can recognize pedestrians in some circumstances. It may provide d\
etection
capability while driving at low as well as higher speeds.
Press the LDA switch to turn the LDA system on. Depress again to turn it\
off.
Note: The system will continue in the last state it was in (ON or OFF) when\
the
engine is started again.
Turning on the LDA system
The Lane Departure Alert system recognizes visible white or yellow lane \
markers
via a camera sensor. The system alerts the driver with a warning buzzer \
sound
and message in the Multi-Information Display (MID) when it detects the\
vehicle
deviating from or swaying multiple times within its lane.
Lane Departure Alert (LDA)

36
The AHB uses an in-vehicle camera sensor to assess the brightness of str\
eetlights,
the lights of oncoming and preceding vehicles, etc., and automatically t\
urns high
beam on or off as necessary.
Auto High Beams (AHB)
(1)
(2)
Switching to constant speed control mode
(3) Acceleration when there are no longer any preceding vehicles driving
slower than the set speed The system accelerates until the set speed is reached. The system then
returns to constant speed cruising.
Note: When your vehicle is too close to a vehicle ahead, and
sufficient automatic deceleration via the cruise control is not
possible, the display will flash and the buzzer will sound to alert the \
driver. An example of this would be if another driver cuts in front of
you while you are following a vehicle. Depress the brake pedal to
ensure an appropriate vehicle-to-vehicle distance.
Note: When the engine is turned off, it will automatically default to DRCC.
TOYOTA SAFETY SENSE
If you are already using DRCC “”, push ON-OFF button to turn the system off
first, then push and hold ON-OFF button for at least 1.5 seconds to swit\
ch.