2016 TOYOTA iM light

802. Instrument cluster
Scion iM_U (12J49U)
uSettings display
nEco Driving Indicator Light (if equipped)
Select to activate/deactivate the Eco Driving Indicator Light.
nLanguage
Select to change the language on the display.
nUnits
Select to change the units of meas ure displayed on the multi-infor-
mation display.
nDrive information 1/Drive information 2
Select to select up to 2 items t hat will be displayed on the Drive
information 1 screen and Drive information 2 screen respectively.
(  P. 78)
nScheduled Maintenance (U.S.A. only)
Select to reset the message indicating maintenance is required
after the required maintenance is performed. ( P. 197)
nInitialize Display
Select to reset the me ter display settings. (P. 320)
nEco Driving Indicator (if equipped)
Eco Driving Indicator will not operate under the following conditions:
lThe shift lever is in any position other than D.
l Sport mode is selected.
l The vehicle speed is approximately 80 mph (130 km/h) or higher. Eco Driving Indicator Light
During Eco-friendly acceleration (Eco
driving), the Eco Driving Indicator Light
will turn on. When the acceleration
exceeds the Zone of Eco driving, or
when the vehicle is stopped, the light
turns off.
Eco Driving Indicator Zone Display
Suggests the Zone of Eco driving with current Eco driving ratio based on
acceleration.
Eco driving ratio based on acceleration
If the acceleration exceeds the Zone of Eco driving, the right side of the
Eco Driving Indicator Zone Display illuminate and the Eco Driving Indica-
tor light will turn off.
Zone of Eco driving
1
2
3
4

812. Instrument cluster
2
Instrument cluster
Scion iM_U (12J49U)n
Brightness of the meters (day mode and night mode)
lThe brightness of the meters are changed between day mode and night
mode.
• Day mode: When the tail lights are off or when the tail lights are on but
the surrounding area is bright
• Night mode: When the tail lights are on and the surrounding area is dark
l When in night mode, the brightness will be reduced slightly unless the
meters are set to the maximum brightness level.
n Suspension of the settings display
lWhile driving, the multi-information display cannot be changed to setting
mode. Before changing the settings, stop the vehicle in a safe place.
l In the following situations, operation of some of the settings display may be
temporarily suspended.
• When a warning message appears on the multi-information display
• When the vehicle begins to move
n When disconnecting and reco nnecting battery terminals
The drive information data will be reset.
n Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
WARNING
nCaution for use while driving
lWhen operating the multi-information display while driving, pay extra
attention to the safety of the area around the vehicle.
l Do not look continuously at the multi-information display while driving as
you may fail to see pedestrians, objects on the road, etc. ahead of the
vehicle.
n The information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear
number appearing on the display. This lag could cause the driver to down-
shift again, causing rapid and excessive engine braking and possibly an
accident resulting in death or injury.
n Cautions during setting up the display
As the engine needs to be running during setting up the display, ensure that
the vehicle is parked in a place with adequate ventilation. In a closed area
such as a garage, exhaust gases including harmful carbon monoxide (CO)
may collect and enter the vehicle. This may lead to death or a serious
health hazard.

853-1. Key information
3
Operation of each component
Scion iM_U (12J49U)
nPanic mode
n If you lose your keys
New genuine keys can be made by your Scion dealer using the other key and
the key number stamped on your key number plate. Keep the plate in a safe
place such as your wallet, not in the vehicle.
n When riding in an aircraft
When bringing a key with wireless remote control function onto an aircraft,
make sure you do not press any buttons on the key while inside the aircraft
cabin. If you are carrying the key in your bag, etc., ensure that the buttons are
not likely to be pressed accidentally. Pressing a button may cause the key to
emit radio waves that could interfere with the operation of the aircraft.
n Conditions affecting the operatio n of the wireless remote control
The wireless remote control function may not operate normally in the follow-
ing situations:
l When the wireless key battery is depleted
l Near a TV tower, electric power plant, gas station, radio station, large dis-
play, airport or other facility that generates strong radio waves or electrical
noise
l When carrying a portable radio, cellular phone or other wireless communi-
cation devices
l When multiple wireless keys are in the vicinity
l When the wireless key is in contact with, or is covered by a metallic object
l When a wireless key (that emits radio waves) is being used nearby
l When the wireless key has been left near an electrical appliance such as a
personal computer
l If window tint with a metallic content or metallic objects are attached to the
rear window
When is pressed for longer than
about one second, an alarm will sound
intermittently and the vehicle lights will
flash to deter any person from trying to
break into or damage your vehicle.
To stop the alarm, press any button on the
wireless remote control.

923-2. Opening, closing and locking the doors
Scion iM_U (12J49U)n
When closing the back door
n Luggage compartment light
The luggage compartment light turns on when the back door is opened.
n If the back door open er is inoperative
The back door can be operated from the inside. Lower the back door using the back door
handle, and make sure to push the back
door down from the outside to close it.
Be careful not to pull the back door
sideways when closing the back door
with the handle.
Using a screwdriver, remove the cover.
To protect the cover, place a rag
between the flathead screwdriver and
the cover as shown in the illustration.
Move the lever.
WARNING
n Caution while driving
lKeep the back door closed while driving.
If the back door is left open, it may hit near-by objects while driving or lug-
gage may be unexpectedly thrown out, causing an accident.
In addition, exhaust gases may enter the vehicle, causing death or a seri-
ous health hazard. Make sure to close the back door before driving.
l Before driving the vehicle, make sure that the back door is fully closed. If
the back door is not fully closed, it may open unexpectedly while driving,
causing an accident.
l Never let anyone sit in the luggage compartment. In the event of sudden
braking or a collision, they are susceptible to death or serious injury.
1
2

943-2. Opening, closing and locking the doors
Scion iM_U (12J49U)
WARNING
lDo not pull on the back door damper stay to close the back door, and do
not hang on the back door damper stay.
Doing so may cause hands to be caught or the back door damper stay to
break, causing an accident.
l If a bicycle carrier or similar heavy object is attached to the back door, it
may suddenly shut again after being opened, causing someone’s hands,
head or neck to be caught and injured. When installing an accessory part
to the back door, using a genuine Scion part is recommended.
NOTICE
nBack door damper stays
The back door is equipped with damper stays that hold the back door in
place.
Observe the following precautions.
Failure to do so may cause damage to the back door damper stay, resulting
in malfunction.
lDo not place your hand on the damper stay or apply lateral forces to it.
lWhen closing the back door, take extra
care to prevent your fingers etc. from
being caught.
l When closing the back door, make sure
to press it lightly on its outer surface. If
the back door handle is used to fully
close the back door, it may result in
hands or arms being caught.
lDo not attach any foreign objects, such
as stickers, plastic sheets, or adhesives
to the damper stay rod.
l Do not touch the damper stay rod with
gloves or other fabric items.
l Do not attach any accessories other
than genuine Scion parts to the back
door.
l Do not place your hand on the damper
stay or apply lateral forces to it.

973-3. Adjusting the seats
3
Operation of each component
Scion iM_U (12J49U)
WARNING
Observe the following precautions. Failure to do so may result in death or
serious injury.
nWhen folding the rear seatbacks down
lDo not fold the seatbacks down while driving.
l Stop the vehicle on level ground, set the parking brake and shift the shift
lever to P (continuously variable transmission) or N (manual transmission).
l Do not allow anyone to sit on a folded seatback or in the luggage compart-
ment while driving.
l Do not allow children to enter the luggage compartment.
l Do not allow anyone to sit on the rear center seat if the rear right seat is
folded down, as the seat belt buckle for the rear center seat belt is th\
en
concealed under the folded seat and cannot be used.
l Be careful not to get your hand caught when folding the rear seatbacks.
l Adjust the position of the front seats before folding down the rear seat-
backs so that the front seats do not interfere with the rear seatbacks when
folding down the rear seatbacks.
n After returning the rear seatback to the upright position
lMake sure that the seatback is securely
locked in position by lightly rocking it
back and forth.
If the seatback is not securely locked,
the red marking will be visible on the
seatback lock release knob. Make sure
that the red marking is not visible.
l Check that the seat belts are not twisted
or caught in the seatback.
If the seat belt gets caught between the
seatback’s securing hook and latch, it
may damage the seat belt.

1033-4. Adjusting the steering wheel and mirrors
3
Operation of each component
Scion iM_U (12J49U)
The height of the rear view mirror can be adjusted to suit your driving
posture.
Adjust the height of the rear view
mirror by moving it up and down.
Reflected light from the headlights of vehicles behind can be reduced
by operating the lever.
Normal position
Anti-glare position
Inside rear view mirror
The rear view mirror’s position can be adjusted to enable suffi-
cient confirmation of the rear view.
Adjusting the height of rear view mirror
Anti-glare function
1
2
WARNING
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident,
resulting in death or serious injury.

106
Scion iM_U (12J49U)
3-5. Opening and closing the windows
The power windows can be opened and closed using the switches.
Operating the switch moves the windows as follows:
Closing
One-touch closing (driver’s win-
dow only)
*
Opening
One-touch opening (driver’s
window only)
*
*
: To stop the window partway, oper- ate the switch in the opposite direc-
tion.
Press the switch to lock the pas-
senger window switches.
Use this switch to prevent children
from accidentally opening or clos-
ing a passenger window.
n The power windows can be operated when
The engine switch is in the “ON” position.
n Operating the power windows after turning the engine off
The power windows can be operated for approximately 45 seconds after the
engine switch is turned to the “ACC” or “LOCK” position. They cannot, how-
ever, be operated once either front door is opened.
n Jam protection function (driver’s window only)
If an object becomes caught between the window and the window frame, win-
dow travel is stopped and the window is opened slightly.
n Pinch protection function (driver’s window only)
While the window is opening, if an object is caught between the door and win-
dow, window travel is stopped.
Power windows
Opening and closing procedures
1
2
3
4
Window lock switch