2016 TOYOTA iM light

66
Scion iM_U (12J49U)
1-2. Theft deterrent system
The indicator light flashes after
the key has been removed from
the engine switch to indicate that
the system is operating.
The indicator light stops flashing
after the registered key has been
inserted into the engine switch to
indicate that the system has been
canceled.
Engine immobilizer system
The vehicle’s keys have built-in transponder chips that prevent
the engine from starting if a key has not been previously regis-
tered in the vehicle’s on-board computer.
Never leave the keys inside the vehicle when you leave the vehi-
cle.
This system is designed to help prevent vehicle theft but does
not guarantee absolute security against all vehicle thefts.

69
Instrument cluster2
Scion iM_U (12J49U)2. Instrument cluster
Warning lights and indicators .......................... 70
Gauges and meters ............ 74
Multi-information display ..... 76

70
Scion iM_U (12J49U)
2. Instrument cluster
The units used on the meters and some indicators may differ depending on
the target region.
Warning lights and indicators
The warning lights and indicators on the instrument cluster and
center panel inform the driver of the status of the vehicle’s vari-
ous systems.
For the purpose of explanation, the following illustration dis-
plays all warning lights a nd indicators illuminated.

712. Instrument cluster
2
Instrument cluster
Scion iM_U (12J49U)
Warning lights inform the driver of malfunctions in the indicated vehi-
cle’s systems.
*: These lights turn on when the engine switch is turned to the “ON” position to indicate that a system check is being performed. They will turn off after
the engine is started, or after a few seconds. There may be a malfunction
in a system if a light does not come on, or turn off. Have the vehicle
inspected by your Scion dealer.
Warning lights
*
(U.S.A.)
Brake system warning
light ( P. 262)*Electric power steering
system warning light
(P. 263)
*
(Canada)
Brake system warning
light ( P. 262)*
Slip indicator ( P. 263)
*
(U.S.A.)
Malfunction indicator
lamp (P. 262)Low fuel level warning
light (P. 263)
*
(Canada)
Malfunction indicator
lamp ( P. 262)Seat belt reminder light
(P. 263)
*SRS warning light
(P. 262)*Tire pressure warning
light ( P. 263)
*
(U.S.A.)
ABS warning light
(P. 263)*Master warning light
(P. 264)
*
(Canada)
ABS warning light
(P. 263)

722. Instrument cluster
Scion iM_U (12J49U)
The indicators inform the driver of the operating state of the vehicle’s
various systems.
*1: These lights turn on when the engine switch is turned to the “ON” position to indicate that a system check is being performed. They will turn off after
the engine is started, or after a few seconds. There may be a malfunction
in a system if a light does not come on, or turn off. Have the vehicle
inspected by your Scion dealer.
*2: The light flashes to indicate that the system is operating.
*3: The light does not turn on when the system is disabled.
*4: This light illuminates on the center panel.
*5: When the outside temperature is approximately 37°F (3°C) or lower, theindicator will flash for approximately 10 seconds, then stay on.
Indicators
Turn signal indicator
(P. 137)*1VSC OFF indicator
(P. 158)
(U.S.A.)
Headlight indicator
(P. 139)*1, 3
(if equipped)
Eco Driving Indicator
Light ( P. 80)
(Canada)
Tail light indicator
(P. 139) *4Security indicator
(P. 66)
Headlight high beam
indicator ( P. 139)
(if equipped)
Sport mode indicator
(P. 132)
Cruise control indicator
( P. 151)
*5Low outside tempera-
ture indicator ( P. 74)
Cruise control “SET”
indicator ( P. 151)
*1, 4“AIR BAG ON/OFF” indi-
cator (P. 45)
*1, 2
Slip indicator ( P. 157)

732. Instrument cluster
2
Instrument cluster
Scion iM_U (12J49U)
WARNING
nIf a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning lights not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by your Scion dealer immedi-
ately if this occurs.

762. Instrument cluster
Scion iM_U (12J49U)
The multi-information display presents the driver with a variety of driv-
ing-related data, such as the current outside temperature. The multi-
information display can also be used to change the display settings
and other settings.
l Outside temperature ( P. 74)
l Shift position and gear position
indicator (if equipped)
( P. 131)
l Pop-up display
In some situations a warning
message or the operation sta-
tus of a system will be tempo-
rarily displayed on the multi-
information display.
l Trip information/Meter light control ( P. 7 7 )
Displays the following items: •Odometer
•Trip meter
• Meter light control
l Menu icons ( P. 78)
Select a menu icon to display its content.
Drive information ( P. 7 8 )
Select to display various drive data.
Warning message display ( P. 269)
Select to display warning messages and measures to be taken if a
malfunction is detected.
Settings display ( P. 80)
Select to change the meter display settings and other settings.
Multi-infor mation display
Display content

772. Instrument cluster
2
Instrument cluster
Scion iM_U (12J49U)
uChanging the display
To change the displayed item,
press the “TRIP” switch.
Each time the switch is pressed,
the displayed item will be
changed.
uDisplay items
nOdometer
Displays the total distance the vehicle has been driven.
nTrip meter A/trip meter B
Displays the distance the vehicle has been driven since the meter
was last reset. Trip meters A and B can be used to record and dis-
play different distances independently.
To reset, display the desired trip meter and press and hold the “TRIP”
switch.
n
Meter light control
Displays the meter light control display.
• The brightness of the meters can be adjusted individually for day mode and night mode
*.
• If the brightness of the meters is adjusted when the tail lights are on, the brightness of the clock and other items will also be adjusted.
• To adjust the brightness, display the meter light control display and press and hold the “TRIP” switch.
*: Day mode and night mode: P. 8 1
Trip information/Meter light control