2016 TOYOTA CAMRY HYBRID low beam

862. Instrument cluster
CAMRY_HV_U (OM33C35U)
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
Turn signal indicator
( P. 170)
*3
“ECO MODE” indicator
(P. 169)
(U.S.A.)
Headlight indicator
(P. 172)*1, 5 Slip indicator ( P. 219)
(Canada)
Tail light indicator
(P. 172) *1VSC OFF indicator
(P. 220)
Headlight high beam
indicator ( P. 172)
*1, 6“PASS AIR BAG ON/
OFF” indicator ( P. 4 9 )
*2Automatic High Beam
indicator (P. 175)*6Security indicator
(P. 78, 80)
*3Cruise control indicator
(P. 185) “READY” indicator
(
P. 161)
*2, 3Radar cruise control
indicator ( P. 189) EV indicator (
P. 7 1 )
*3Cruise control set indica-
tor (P. 185)*3EV drive mode indicator
(P. 166)
*2, 3LDA (Lane Departure
Alert) indicator
(P. 109)*3, 7
Low outside tempera-
ture indicator ( P. 88)
*1, 2, 4Pre-collision system
warning light ( P. 224)

172
CAMRY_HV_U (OM33C35U)
4-3. Operating the lights and wipers
Turning the end of the lever turns on the lights as follows:The headlights, day-
time running lights
( P.
173) and all the lights
listed below turn on and
off automatically.
(When the power
switch is in ON mode)
The side marker, park-
ing, tail, license plate,
daytime running lights
(  P. 173) and instru-
ment panel lights turn
on.
The headlights and all the lights listed above (except day-
time running lights) turn on.
*1 The daytime running lights turn off.
*2 The daytime running lights turn on. (  P. 173)
*1:For U.S.A.
*2: For Canada
With the headlights on, push
the lever away from you to turn
on the high beams.
Pull the lever toward you to the
center position to turn the high
beams off.
Pull the lever toward you and
release it to flash the high
beams once.
You can flash the high beams with the headlights on or off.
Headlight switch
The headlights can be operated manually or automatically.
Operating instructions
1
2
3
4
Turning on the high beam headlights
1
2

1764-3. Operating the lights and wipers
CAMRY_HV_U (OM33C35U)
When all of the following conditions are fulfilled, high beam will be
automatically turned on:
lVehicle speed is above appr oximately 21 mph (34 km/h).
l The area ahead of the vehicle is dark.
l There are no oncoming or preceding vehicles with headlights or tail
lights turned on.
l There are few streetlights on the road ahead.
If any of the following conditions are fulfilled, high beam will be auto-
matically turned off:
l Vehicle speed drops below approximately 17 mph (27 km/h).
l The area ahead of the vehicle is not dark.
l Oncoming or preceding vehicles have headlights or tail lights
turned on.
l There are many streetlights on the road ahead.
nSwitching to low beam
Pull the lever to the original
position.
nSwitching to high beam
Turn the light switch to .
The Automatic High Beam indi-
cator will turn off and the high
beam indicator will turn on.
High beam automatic turning on or off conditions
Turning the high beam on/off manually

1774-3. Operating the lights and wipers
4
Driving
CAMRY_HV_U (OM33C35U)
nThe Automatic High Beam can be operated when
The power switch is in ON mode.
n Camera sensor detection information
lHigh beam may not be automatically turned off in the following situations:
• When oncoming vehicles suddenly appear from a curve
• When the vehicle is cut in front of by another
• When oncoming or preceding vehicles are hidden from sight due to
repeated curves, road dividers or roadside trees
• When oncoming vehicles appear from the faraway lane on wide road
• When oncoming or preceding vehicles have no lights
l High beam may be turned off if an oncoming vehicle that is using fog lights
without using the headlights is detected.
l House lights, street lights, red traffic signals, and illuminated billboards or
signs may cause the high beam to turn off.
l The following factors may affect the amount of time taken to turn high beam
on or off:
• The brightness of headlights, fog lights, and tail lights of oncoming and
preceding vehicles
• The movement and direction of oncoming and preceding vehicles
• When a oncoming or preceding vehicle only has operational lights on one side
• When a oncoming or preceding vehicle is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road surface
etc.)
• The number of passengers and amount of luggage
l High beam may be turned on or off when unexpected by the driver.

1784-3. Operating the lights and wipers
CAMRY_HV_U (OM33C35U)l
In the situations below, the system may not be able to correctly detect the
surrounding brightness levels, and may flash or expose nearby pedestrians
to the high beam. Therefore, you should consider turning the high beams on
or off manually rather than relying on the Automatic High Beam system.
• In bad weather (rain, snow, fog, sandstorms etc.)
• The windshield is obscured by fog, mist, ice, dirt etc.
• The windshield is cracked or damaged.
• The camera sensor is deformed or dirty.
• The camera sensor temperature is extremely high.
• Surrounding brightness levels are equal to those of headlights, tail lights
or fog lights.
• Vehicles ahead have headlights that are either switched off, dirty, are changing color, or are not aimed properly.
• When driving through an area of in termittently changing brightness and
darkness.
• When frequently and repeatedly driving ascending/descending roads, or
roads with rough, bumpy or uneven surfaces (such as stone-paved
roads, gravel tracks etc.).
• When frequently and repeatedly taking curves or driving on a winding
road.
• There is a highly reflective object ahead of the vehicle, such as a sign or a mirror.
• The back of a vehicle ahead is highly reflective, such as a container on a truck.
• The vehicle’s headlights are damaged or dirty.
• The vehicle is listing or tilting, due to a flat tire, a trailer being towed etc.
• The high beam and low beam are repeatedly being switched between in
an abnormal manner.
• The driver believes that the high beam may be causing problems or dis- tress to other drivers or pedestrians nearby.
n Temporarily lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
Turn the power switch off while the following conditions are met.
• The headlight switch is in .
• The headlight switch lever is in high beam position. Turn the power switch to ON mode.
Within 5 seconds after , repeat pulling the headlight switch lever to the
original position then pushing it to the high beam position quickly 9 times,
then leave the lever in high beam position.
Automatic High Beam (headlights) may turn on even the vehicle is stopped.
n If a warning message for the Automatic High Beam is shown on the
multi-information display
It may indicate a malfunction in the system. Contact your Toyota dealer.
n Customization
The Automatic High Beam can be deactivated.
(Customizable features: P. 535)
1
2
32

1794-3. Operating the lights and wipers
4
Driving
CAMRY_HV_U (OM33C35U)
WARNING
nLimitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to
observe your surroundings and turning high beam on or off manually if nec-
essary.
NOTICE
nNotes when using the Au tomatic High Beam system
Observe the following to ensure that the Automatic High Beam functions
correctly.
l Do not place items on the dashboard. There is a possibility that the cam-
era sensor will mistake items reflected in the windshield for streetlights,
the headlights of other vehicles, etc.
l Do not install a parking tag or any other accessories near or around the
camera sensor.
l Do not overload the vehicle.
l Do not modify the vehicle.
l If the windshield needs to be replaced, contact your Toyota dealer.
lDo not touch the camera sensor.
l Do not subject the camera sensor to a
strong impact.
l Do not disassemble the camera sensor.
l Do not spill liquid onto the camera sen-
sor.
l Do not apply window tinting or stickers
to the camera sensor or the area of
windshield near the camera sensor.

3837-1. Maintenance and care
7
Maintenance and care
CAMRY_HV_U (OM33C35U)
NOTICE
nCleaning detergents
lDo not use the following types of detergent, as they may discolor the vehi-
cle interior or cause streaks or damage to painted surfaces:
• Non-seat portions: Organic substances such as benzene or gasoline,
alkaline or acidic solutions, dye, and bleach
• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco- hol
l Do not use polish wax or polish cleaner. The instrument panel’s or other
interior part’s painted surface may be damaged.
n Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of
leather surfaces:
lRemove any dust or dirt from leather surfaces immediately.
l Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
l Do not place items made of vinyl, plastic, or containing wax on the uphol-
stery, as they may stick to the leather surface if the vehicle interior heats
up significantly.
n Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio system may be damaged if water comes
into contact with electrical components such as the audio system above or
under the floor of the vehicle. Water may also cause the body to rust.
n When cleaning the inside of the wi ndshield (vehicles with LDA [Lane
Departure Alert] and Automatic High Beam)
Be careful not to touch the camera sensor ( P. 202).
If the camera is accidentally scratched or hit, LDA and Automatic High
Beam may not operate properly or may cause a malfunction.
n Cleaning the inside of the rear window
l Do not use glass cleaner to clean the rear window, as this may cause
damage to the rear window defogger heater wires or antenna. Use a cloth
dampened with lukewarm water to gently wipe the window clean. Wipe the
window in strokes running parall el to the heater wires or antenna.
l Be careful not to scratch or damage the heater wires or antenna.

4307-3. Do-it-yourself maintenance
CAMRY_HV_U (OM33C35U)
Check the wattage of the light bulb to be replaced. (P. 512)
Light bulbs
You may replace the following bulb s yourself. The difficulty level
of replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perform, contact your Toyota
dealer.
For more information about repl acing other light bulbs, contact
your Toyota dealer.
Preparing for light bulb replacement
Bulb locations
FrontRear
Headlight high beams/daytime
running lights (halogen bulb)
Headlight low beams
Front side marker lights
Front turn signal/parking lights
(bulb type) Back-up lights
Rear turn signal lights
Stop/tail/rear side marker
lights
License plate lights
1
2
3
4
1
2
3
4