2016 TOYOTA C-HR change time

7088-2. Steps to take in an emergency
C-HR_OM_Europe_OM10528E
■ If the following messages are shown (AWD models only)
The system may be an overheated. Reduce the vehicle speed or stop the
vehicle in a safe place.
• “AWD System Overheated 2WD Mode Engaged”
• “AWD System Overheated Switching to 2WD Mode”
■ If “Oil Maintenance Required Soon” is shown
Indicates that the engine oil is scheduled to be changed. (The indicator will
not work properly unless the message has been reset.)
Check the engine oil, and change if necessary. After changing the engine oil,
the message should be reset. ( P. 621)
■ If “Oil Maintenance Required Visit Your Dealer.” is shown
Indicates that the engine oil should be changed. (After the engine oil is
changed and the message has been reset.)
Check and change the engine oil, and oil filter by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer. After changing
the engine oil, the message should be reset. ( P. 621)
■ If “A New Key has been Registered Contact Your Dealer for Details” is
shown (vehicles with a smart entry & start system)
This message will be displayed each time the driver's door is opened when
the doors are unlocked from the outside for approximately one week after a
new electronic key has been registered.
If this message is displayed but you have not had a new electronic key regis-
tered, ask any authorized Toyota retailer or Toyota authorized repairer, or any
reliable repairer to check if an unknown electronic key (other than those in
your possession) has been registered.

7498-2. Steps to take in an emergency
8
When trouble arises
C-HR_OM_Europe_OM10528E
■Stopping the engine
Set the parking brake, shift the shift leve r to P (Multidrive) or N (manual trans-
mission) and press the engine switch as you normally do when stopping the
engine.
■ Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the
electronic key battery be replaced immediately when the battery is depleted.
( P. 652)
■ Alarm (if equipped)
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set,
the alarm may be triggered.
■ Changing engine switch modes
Release the brake pedal (Multidrive) or clutch pedal (manual transmission)
and press the engine switch in step above.
The engine does not start and modes will be changed each time the switch is
pressed. ( P. 238)
■ When the electronic key does not work properly
● Make sure that the smart entry & start system and push button start has not
been deactivated in the customization setting. If it is off, turn the function on.
(Customizable features P. 776)
● Check if battery-saving mode is set. If it is set, cancel the function.
( P. 173)
WARNING
■When using the mechanical key and operating the power windows
Operate the power window after checking to make sure that there is no pos-
sibility of any passenger having any of their body parts caught in the side
window. Also, do not allow children to operate the mechanical key. It is pos-
sible for children and other passengers to get caught in the power window.
3

7769-2. Customization
C-HR_OM_Europe_OM10528E
Customizable features
■Changing using the multi-information display
Vehicles with monochrome display
Press the “DISP” switch to display the setting screen while the
vehicle is stopped, and then press and hold the “DISP” switch to
display the customize mode screen.
Press the “DISP” switch and select the item, and then press and
hold the “DISP” switch.
Press the “DISP” switch and select the desired setting, and then
press and hold the “DISP” switch.
To exit the customize mode, press the “DISP” switch to select the
“EXIT”, and then press and hold the “DISP” switch.
Your vehicle includes a variety of electronic features that can be
personalized to your preferences. The settings of these features
can be changed using the multi-information display, on the navi-
gation/multimedia system or at any authorized Toyota retailer or
Toyota authorized repairer, or any reliable repairer.
Customizing vehicle features
1
2
3

7779-2. Customization
9
Vehicle specifications
C-HR_OM_Europe_OM10528E
Vehicles with color display
Press “ ” or “” of the meter control switches, select .
Press “ ” or “” of the meter control switches, select “Meter
Settings”, and then press .
Press “ ” or “” of the meter control switches, select the item,
and then press .
Press “ ” or “” of the meter control switches, select the desired
setting, and then press .
To go back to the previous screen or exit the customize mode,
press .
■Changing on the navigation or multimedia system screen
(vehicles with a navigation or multimedia system)
Press .
Select “Vehicle” on the “Setup” screen.
Select the desired item.
Various settings can be changed. Refer to the list of settings that
can be changed for details.
1
2
3
4
1
2

7789-2. Customization
C-HR_OM_Europe_OM10528E
Some function settings are changed simultaneously with other func-
tions when customized. Contact any authorized Toyota retailer or
Toyota authorized repairer, or any reliable repairer for further details.
Settings that can be changed using the multi-information display
Settings that can be changed using the navigation or multimedia
system screen (vehicles with a navigation or multimedia system)
Settings that can be changed by your Toyota dealer
Definition of symbols: O = Av ailable, — = Not available
Customizable features
1
2
3

7839-2. Customization
9
Vehicle specifications
C-HR_OM_Europe_OM10528E
■Power windows ( P. 201)
*1: Vehicles without a smart entry & start system
*2: Vehicles with a smart entry & start system
■Turn signal lever ( P. 255)
FunctionDefault settingCustomized
setting
Key*1 or mechanical
key*2 linked operation
(open)
OffOn––O
Key*1 or mechanical
key*2 linked operation
(close)
OffOn––O
Wireless remote control
linked operation (open)OffOn––O
Wireless remote control
linked operation (close)OffOn––O
Key*1 or mechanical
key*2, wireless remote
control linked operation
signal (buzzer)
OnOff––O
123
FunctionDefault settingCustomized
setting
Times of flashing of the
lane change signal flash-
ers
3
Off
––O5
7
123