2016 SUBARU FORESTER ignition

About EyeSight
15
●Selector indicator/shift position indicator
xDisplays the selector lever position or the selected gear position.
xFor turbo models, when the Adaptive Cruise Control / Conventional Cruise Control is set
while S# (Sports Sharp mode) of SI-DRIVE is selected, the display switches from the gear
position to the D position.
●Lane indicator
xWhen the Lane Departure Warning is activated, both the left and right indicators flash
simultaneously.
xWhen the Lane Sway Warning is activated, the left and right indicators flash alternately.
* Refer to pages 58 and 61.
●Steering wheel indicator
Flashes when the Lane Departure Warning or Lane Sway Warning is active.
* Refer to pages 58 and 61.
●EyeSight temporary stop indicator
xIf a malfunction occurs in the EyeSight system, the Pre-Collision Braking System OFF
indicator light and the Lane Departure Warning OFF indicator light illuminate and a sym-
bol from “E1” to “E3” will be displayed on the meter display. However, when the main
cruise control is in the OFF position, the symbol will not be displayed.
xWhen it is displayed, none of the EyeSight functions can be used except for Conventional
Cruise Control.
* Refer to page 77.
●Customization display
The settings of the alarm volume, the lead vehicle acquisition sound and the lead vehicle
start alert function can be customized when all of the following conditions are met: the
engine is running, the main cruise control is in the OFF position and the selector lever is in
the P position.
* Refer to page 79.
●EyeSight warning light
xThis indicator illuminates or flashes when a malfunction occurs in the EyeSight system.
xIt also illuminates when the ignition switch is turned to the ON position and then it turns off
approximately 5 seconds after the engine starts.
xWhen it is illuminated or flashing, none of the EyeSight functions can be used (including
Adaptive Cruise Control and the Pre-Collision Braking System, etc.).
* Refer to page 76.
●Brake system warning light (red)
If the brake system warning light illuminates during driving while the parking brake is fully
released, turn off the Pre-Collision Braking System. Also, do not use Adaptive Cruise Con-
trol or Conventional Cruise Control.
*Refer to the vehicle Owner’s Manual for details.

About EyeSight
16
●Lane Departure Warning OFF indicator light
xThis indicator illuminates when the Lane Departure Warning and Lane Sway Warning are
off.
xIt also illuminates when the ignition switch is turned to the ON position, and then turns off
approximately 7 seconds after the engine starts.
* Refer to page 60.
●Pre-Collision Braking System OFF indicator light
xIlluminates when the Pre-Collision Braking System and Pre-Collision Throttle
Management are off.
xIt also illuminates when the ignition switch is turned to the ON position, and then turns off
approximately 7 seconds after the engine starts.
* Refer to pages 51 and 57.
■Multi function display
●
Your own vehicle speed indicator
Indicates your own vehicle speed with a red indicator.
●Set vehicle speed indicator
Indicates the set vehicle speed.
* Refer to page 29.
Set vehicle speed display
Your own vehicle
indicator
Your own vehicle
speed indicatorLead vehicle
indicator
Lead vehicle
distance indicator
S00885

Pre-Collision Braking System
51
When pressing and holding the Pre-Collision
Braking System OFF switch for approximately
2 seconds (or longer), a single short beep will
sound and the Pre-Collision Braking System
(including Pre-Collision Brake Assist) will turn
off. When this control is turned off, the Pre-
Collision Braking System OFF indicator light
on the instrument panel illuminates. To turn
the control back on, press and hold the Pre-
Collision Braking System OFF switch for
approximately 2 seconds or longer again.
When this control is turned on, the Pre-
Collision Braking System OFF indicator light
will turn off.
■Pre-Collision Braking System OFF indicator light
This indicator light illuminates when the
ignition switch is turned to the ON position,
and remains illuminated for approximately 7
seconds after the engine starts. It turns on
when the Pre-Collision Braking System is
turned off.
It also illuminates under the following
conditions.
xWhen the VDC OFF switch is pressed and
VDC is canceled
xWhen the EyeSight system has a
malfunction
* Refer to page 76.
xWhen the EyeSight system has stopped
temporarily
* Refer to page 77.
Turning off the Pre-Collision Braking System
NOTE
xWhen the Pre-Collision Braking System is turned off, the Pre-Collision
Throttle Management Control function is also turned off.
xEven when the Pre-Collision Braking System is turned off, if the ignition
switch is turned off and the engine is then restarted, the Pre-Collision
Braking System will be turned on. The system default setting when the
vehicle is restarted in “ON”.
S00813
S00840

Pre-Collision Throttle Management
57
When pressing and holding the Pre-Collision Braking System OFF switch for approximately
2 seconds or longer a single short beep will sound and the Pre-Collision Throttle
Management System will turn off. When this function is turned off, the Pre-Collision Braking
System OFF indicator light on the instrument panel illuminates.
To turn the system back on, press and hold the Pre-Collision Braking System OFF switch
again for approximately 2 seconds or longer. When this function is turned on, the Pre-
Collision Braking System OFF indicator light turns off.
* Refer to page 51.
Turning off Pre-Collision Throttle Management
NOTE
xWhen Pre-Collision Throttle Management is turned off, the Pre-Collision
Braking System also turns off.
xEven when Pre-Collision Throttle Management is turned off, if the ignition
switch is turned off and the engine is restarted, Pre-Collision Throttle
Management will be turned on. The default setting for Pre-Collision
Throttle Management when the vehicle is restarted is “ON”.
S00813S00840

Lane Departure Warning
60
When pressing and holding the Lane
Departure Warning OFF switch for approxi-
mately 2 seconds or longer, a single short
beep will sound and the Lane Departure
Warning will turn off. When this function is
turned off, the Lane Departure Warning OFF
indicator light on the instrument panel will illu-
minate.
To turn the function back on, press and hold
the Lane Departure Warning OFF switch
again. When the function is turned on, the
Lane Departure Warning OFF indicator light
will turn off.
■Lane Departure Warning OFF indicator light
This indicator illuminates when the ignition
switch is turned to the ON position, and then
approximately 7 seconds after the engine
starts, it turns off. It turns on when the Lane
Departure Warning feature is turned off.
It also illuminates under the following
conditions.
xWhen the VDC OFF switch is pressed and
VDC is canceled
xWhen the EyeSight system has a
malfunction
* Refer to page 76.
xWhen the EyeSight system has stopped
temporarily
* Refer to page 77.
Turning off Lane Departure Warning
NOTE
xWhen the Lane Departure Warning is turned off, the Lane Sway Warning is
also turned off.
xEven when the Lane Departure Warning is turned off, if the ignition switch
is turned off and then the engine is restarted, the Lane Departure Warning
will be turned on. The default setting for the Lane Departure Warning when
the vehicle is restarted is “ON”.
S00814
S00847

Lane Sway Warning
63
Press and hold the Lane Departure Warning OFF switch for approximately 2 seconds or
longer to turn off the Lane Sway Warning. When this function is turned off, a single short
beep sounds and the Lane Departure Warning OFF indicator light on the instrument panel
illuminates.
To turn the function back on, press and hold the Lane Departure Warning OFF switch again
for approximately 2 seconds or longer. When the function is turned on, the Lane Departure
Warning OFF indicator light turns off.
* Refer to page 60.
Turning off Lane Sway Warning
NOTE
xWhen the Lane Sway Warning is turned off, the Lane Departure Warning is
also turned off.
xEven when the Lane Sway Warning is turned off, if the ignition switch is
turned off and then the engine is restarted, the Lane Sway Warning will be
turned on. The default setting for the Lane Sway Warning after the vehicle
is restarted is “ON”.
S00814S00847

Customizing functions
79
Customizing functions
■How to customize
The customizing function can be operated when the engine is running, the main cruise
control is off (the or indicator is not displayed on the meter) and the select lever
is in the position.
(1) To turn the customization mode on, press the (following distance setting) switch for
approximately 2 seconds or more.
(2) When the (following distance setting) switch is pressed, the item of customization
and the current setting are displayed on the meter display. Every time the switch is
pressed, the item of customization will be changed.
(3) While pressing the RES/+ or SET/- switch,
the setting is changed. (When the setting
is changed, a beep sounds.)
(4) The setting can be determined when the
RES/+ or SET/- switch is released.
(5) To exit from the customizing mode, perform one of the following operations.
xPlace the ignition switch to the ACC or LOCK (OFF) position.
xTurn the main cruise control on.
xShift the select lever to any other position except for the position.Display Item Setting Default setting
Warning volume Max/Mid/Min Mid
Lead vehicle acquisition alert Activate/Deactivate Activate
Lead Vehicle Start Alert Activate/Deactivate Activate
P
S00829S00867
S00867
Max Mid MinEX.: Warning volume setting
P

Customizing functions
80
●Warning volume setting
The warning volume can be set to
Max/Mid/Min.
When the RES/+ or SET/- switch is pressed,
the setting will change to the next and 3 short
beeps will sound in the volume corresponding
to the setting.
●Lead vehicle acquisition alert setting
The lead vehicle acquisition alert function
setting can be activated or deactivated.
When the RES/+ or SET/- switch is pressed,
the setting will change to the next. When the
setting is changed to be activated, a short
beep will sound. When the setting is changed
to be deactivated, no beeps will sound.
●Lead Vehicle Start Alert setting
The Lead Vehicle Start Alert function setting
can be activated or deactivated.
When the RES/+ or SET/- switch is pressed,
the setting will change to the next. When the
setting is changed to be activated, a two-tone
beep will sound. When the setting is changed
to be deactivated, this function is turned off
and no beeps will sound.
NOTE
Even when the engine is restarted after the ignition switch is placed in the
LOCK (OFF) position, the setting will be restored to the previous status
before the ignition switch is placed in the LOCK (OFF) position.
S00869
Setting
Max
Mid
MinDisplay
S00870
Setting
Activate
Deactivate
Display
S00871
Setting
Activate
Deactivate
Display