2016 SMART FORTWO light

Useful information
i
This Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's Man- ual. Country-specific differences are pos-
sible. Bear in mind that your vehicle may
not feature all functions described here.
This also applies to safety-relevant sys-
tems and functions.
iRead the information on qualified spe-
cialist workshops: (Ypage 20).
Exterior lighting
General notes
For reasons of safety, smart recommends that
you drive with the lights switched on even
during the daytime. In some countries, oper-
ation of the headlamps varies due to legal
requirements and self-imposed obligations.
Exterior lighting settings
Operation
0043Combination switch control
0044Marking
0049003FLights off
004A 0060standing lamp, parking lamp,
license plate lighting
004B0057High-beam headlamps
004C0058Automatic headlamp mode, control-
led by the light sensor
004D0058Low-beam headlamps
006CMarking
006DCombination switch middle ring
00BE005AFront fog lamps
00BF005ERear fog lamp
If you hear a warning tone when you leave the
vehicle, the lights may still be switched on.
XTurn combination switch control 0043until
0058 or003F is at marking 0044.
When in the 0058position the exterior light-
ing switches off automatically if you:
Rswitch off the engine
Ropen the driver's door
Rlock the vehicle
Rdo not switch on the high-beam headlamps
Automatic headlamp mode
0058 is the favored light switch setting. The
light setting is automatically selected
according to the brightness of the ambient
light (exception: poor visibility due to
weather conditions such as fog, snow or
spray):
RWith the engine running: depending on the ambient light conditions, the daytime
driving lights or the parking and low-beam
headlamps are switched on or off automat-
ically
XTo switch on automatic headlamp mode: turn
combination switch control 0043until 0058
is at marking 0044.
GWARNING
When the light switch is set to 0058, the
low-beam headlamps may not be switched on
automatically if there is fog, snow or other causes of poor visibility due to the weather
Exterior lighting67
>> Lights and windshield wipers.
Z

conditions such as spray. There is a risk ofan accident.
In such situations, turn the light switch to
0058.
The automatic headlamp feature is only an
aid. The driver is responsible for the vehi-
cle's lighting at all times.
Low-beam headlamps
XTo switch on: turn combination switch con-
trol 0043until 0058is at marking 0044.
The 0058 indicator lamp in the instrument
cluster lights up.
Parking lamps
XTo switch on: turn combination switch con-
trol 0043until 0060is at marking 0044.
Canada only: the standing lamps are only
switched on when the engine is switched off.
When the engine is running, the low-beam
headlamps are switched on.
Front fog lamps
Only vehicles with front foglamps have the
"Foglamps" function.
XTo switch on: make sure that the standing
lamps or low-beam headlamps are switched on.
XTurn combination switch middle ring 006D
until marking 006Cis at 005A.
The 005A indicator lamp in the instrument
cluster lights up.
After releasing, the middle ring returns
automatically back to the neutral position.
XTo switch off: turn combination switch
middle ring 006Duntil marking 006Cis at
005A.
The 005A indicator lamp in the instrument
cluster goes out.
After releasing, the middle ring returns
automatically back to the neutral position.
iIf you switch off the engine (only in the
0058 position) or turn off the lights, the
foglamps are also switched off.
Rear fog lamp
XTo switch on: make sure that the fog lamps
or low-beam headlamps are switched on.
XTurn combination switch middle ring 006D
until marking 006Cis at 005E.
The 005E indicator lamp in the instrument
cluster lights up.
After releasing, the middle ring returns
automatically back to the neutral position.
XTo switch off: turn combination switch
middle ring 006Duntil marking 006Cis at
005E.
The 005E indicator lamp in the instrument
cluster goes out.
After releasing, the middle ring returns
automatically back to the neutral position.
iIf you switch off the engine (only in the
0058 position) or turn off the lights, the
rear foglamps are also switched off.
Switching on the turn signals
XStart the engine.
XTo indicate briefly: press the combination
switch briefly to the pressure point in the direction of arrow 0043(right turn signal)
or 0044 (left turn signal).
The corresponding turn signal flashes
three times.
XTo indicate: press the combination switch
beyond the pressure point in the direction
of arrow 0043(right turn signal) or 0044(left
turn signal).
68Exterior lighting
>> Lights and windshield wipers.

Switching on the high-beam headlamps
and headlamp flasher
High-beam headlamps
XTo switch on: start the engine.
XTurn the combination switch control until
0057or0058 (if available) is at the mark-
ing.
XPress the combination switch beyond the
pressure point in the direction of
arrow 0043.
The 0057 indicator lamp in the instrument
cluster lights up.
XTo deactivate: move combination switch 0043
back to its normal position.
The 0057 indicator lamp in the instrument
cluster goes out.
High-beam flasher
XTo switch on: pull the combination switch
in the direction of arrow 0044.
Hazard warning lamps
The hazard warning lamps automatically
switch on if:
Ran air bag is deployed
Rthe vehicle decelerates rapidly from a
speed of above 45 mph (70 km/h) and comes to
a standstill
XTo switch on the hazard warning lamps:
press button0043.
All turn signals flash. If you now switch on
a turn signal using the combination switch,
only the turn signal lamp on the corre-
sponding side of the vehicle will flash.
XTo switch off the hazard warning lamps:
press button 0043.
The hazard warning lamps switch off automat- ically if the vehicle reaches a speed of above
6 mph (10 km/h) again after a full brake appli-
cation.
iThe hazard warning lamps still operate if
the ignition is switched off.
Headlamps fogged up on the inside
Certain climatic and physical conditions
may cause moisture to form in the headlamp.
This moisture does not affect the function-
ality of the headlamp.
Interior lighting
Overview
0043Interior lighting
0044Switches the left-hand reading lamp
on/off
0087Depending on the position of the switch:
Interior lighting switched on
Automatic interior lighting control on
Interior lighting69
>> Lights and windshield wipers.
Z

Interior lighting switched off
0085Switches the right-hand reading lamp on/
off
The interior lighting is switched on when a
door is open: if the corresponding door is
closed correctly the interior lighting goes
out.
Interior lighting control
If the doors are unlocked with the remote con-
trol, the interval timer for the interior
lighting is triggered. The interval timer
restarts when a door is opened.
The front interior lighting and the luggage
compartment light go out gradually.
The interior lighting interval timer is
switched off:
Rif a door remains open, the interior light-
ing switches off after 15 minutes without
dimming
Rif all doors (with additional locking mech-
anism) are closed, the interior lighting
switches off after 15 seconds
Rif all doors (without locking mechanism)
are closed, the interior lighting switches
off after 3 to 4 minutes
Ras soon as the engine is started and for as
long as the engine is running
Replacing bulbs
Important safety notes
GWARNING
Bulbs, lamps and connectors can get very
hot when operating. If you change a bulb,
you could burn yourself on these compo-
nents. There is a risk of injury.
Allow these components to cool down before changing a bulb.
Do not use a bulb that has been dropped or if
its glass tube has been scratched.
The bulb may explode if:
Ryou touch it
Rit is hot
Ryou drop it
Ryou scratch it
Only operate bulbs in enclosed lamps
designed for that purpose. Only fit spare
bulbs of the same type and the specified volt-
age.
Marks on the glass tube reduce the service
life of the bulbs. Do not touch the glass tube
with your bare hands. If necessary, clean the
glass tube when cold with alcohol or spirit
and rub it off with a lint-free cloth.
Protect bulbs from moisture during opera-
tion. Do not allow bulbs to come into contact
with liquids.
Replace only the bulbs listed (
Ypage 70).
If you require assistance replacing bulbs,
consult a qualified specialist workshop.
If the new bulb still does not light up, consult
a qualified specialist workshop.
The daytime driving lights and part of the
rear light clusters of your vehicle are equip-
ped with LED light bulbs. Do not replace these
bulbs yourself. Contact a qualified special-
ist workshop which has the necessary spe-
cialist knowledge and tools to carry out the
work required.
Headlamps and lamps are an important aspect
of vehicle safety. You must therefore make
sure that these function correctly at all
times. Have the headlamp setting checked
regularly.
Overview: changing bulbs/bulb types
You can replace the following bulbs. The bulb
type can be found in the legend.
0043Low-beam/high-beam headlamps: HB2
0044Turn signal lamp: PY 21 W
0087Foglamps: H16
70Replacing bulbs
>> Lights and windshield wipers.

Tail lamp
0043
Tail lamp/brake lamp/side marker lamp:
P 21 5 W
0044Rear fog lamp: P 21 W
0087Backup lamp: W 16 W
0085Turn signal lamp: PY 21 W
Tail lamps (vehicles with partial LEDs)
0043
Turn signal lamp: PY 21 W
0044Backup lamp: W 16 W
0043License plate lighting: W 5 W
0043Side turn signal lamps: WY 5 W
0043Interior lighting: W 5 W
Changing the front bulbs
Important safety notes
GWARNING
The radiator fan may continue to run after
the engine has been switched off or start
without warning. There is a risk of injury.
If you need to operate in the front area:
Rswitch off the ignition
Rtake off jewelry and watches
Rnever reach into the fan rotation area
Rkeep clothing and hair, for example, away
from the fan.
Replacing bulbs71
>> Lights and windshield wipers.
Z

Turn signal
XTo remove the cover in the front wheel
arch:switch off the lighting system.
XTurn the front wheels inwards.
XPress spring clip 0043down.
XSlide cover 0044back and remove it.
XTurn bulb holder 0043anti-clockwise and
remove.
XTake the bulb out of bulb holder 0043.
XInsert the new bulb into bulb holder 0043.
XInsert bulb holder0043and turn it clockwise
until it engages.
XTo fit the cover in the front wheel arch:
insert cover 0044again and lock in place.
Low-beam/high-beam headlamps
XSwitch off the lights.
XOpen the service cover (Ypage 151).
XRemove cover 0043.
XPull out the connector.
XSimultaneously press retainer 0044forward
and to the right and then remove the lamp.
XInsert the new bulb and engage it in place.
XInsert the connector.
XPosition cover 0043and press into place.
Front fog lamps
Due to their location, have the bulbs in the
front fog lamps changed at a qualified spe-
cialist workshop.
XSwitch off the lights.
XRemove the two screws 0043at the bottom of
the front wheel arch using a suitable tool.
XBend back the cover using your hand.
XTurn the bulb holder anti-clockwise and
remove it.
XTake the bulb out of the bulb holder.
XInsert the new bulb into the bulb holder.
XInsert the bulb holder and turn it clockwise until it engages.
72Replacing bulbs
>> Lights and windshield wipers.

XBend the cover back into position.
XTighten the two screws0043again.
Side turn signal lamps
XInsert a flat tool into recess 0043and lever
side turn signal lamp 0044forwards and out.
XRemove the bulb holder from side turn sig-
nal lamp 0044by turning it a quarter turn
anti-clockwise.
XPull the bulb out of the bulb holder.
XInsert the new bulb into the bulb holder.
XInsert the bulb holder into side turn signal
lamp 0044and turn it a quarter turn clock-
wise.
XInsert side turn signal lamp 0044.
Changing the rear bulbs
Tail lamp
XSwitch off the lights.
XTo remove: open the upper and lower tail-
gate (Ypage 57).
XRemove two screws 0043on the tail lamp using
a suitable slotted screwdriver.
XCarefully take out the lamp.
XTo release the connector: insert a suitable
slotted screwdriver under the plastic
hanger, lift a small plastic piece upwards
and remove the connector.
Bulb holder
0043
Tail lamp/brake lamp/side marker lamps
(only vehicles without partial LEDs)
0044Turn signal
0087Backup lamp
0085Rear foglamp (vehicles without partial
LEDs)
XUnclip four bulb holder tabs 0083and care-
fully remove the bulb holder.
XPull out the corresponding bulb.
XInsert the new bulb.
XRe-install bulb holder.
Four bulb holder tabs 0083must audibly
engage.
XInsert the connector.
XInsert the lamp again.
XTighten the two screws 0043on the tail lamp
again.
Replacing bulbs73
>> Lights and windshield wipers.
Z

License plate lamp
XTo remove:release catch 0043of the lamp lens
using a suitable tool.
XRemove the lamp lens.
XTake bulb 0043out of the bulb holder.
XInsert the new bulb into the bulb holder.
XRe-insert the lamp lens into the license
plate lamp.
Replacing the interior lighting
XRemove lamp lens 0043with a flat tool, e.g. a
screwdriver.
XTake the bulb to be replaced out of the bulb
holder.
XInsert the new bulb into the bulb holder.
XInsert lamp lens 0043.
Windshield wipers
Switching the windshield wipers
on/off
!
Do not operate the windshield wipers
when the windshield is dry, as this could
damage the wiper blades. Moreover, dust
that has collected on the windshield can
scratch the glass if wiping takes place
when the windshield is dry.
If it is necessary to switch on the wind-
shield wipers in dry weather conditions,
always use washer fluid when operating the
windshield wipers.
!Make sure that the front windshield wip-
ers are free of ice. The wiper motor could
otherwise overheat.
!If the windshield wipers leave smears on
the windshield after the vehicle has been
washed in an automatic car wash, wax or
other residues may be the reason for this.
Clean the windshield using washer fluid
after washing the vehicle in an automatic
car wash.
!Vehicles with a rain sensor: if the wind-
shield becomes dirty in dry weather con-
ditions, the windshield wipers may be
activated inadvertently. This could then
damage the windshield wiper blades or
scratch the windshield.
For this reason, you should always switch
off the windshield wipers in dry weather.
74Windshield wipers
>> Lights and windshield wipers.