2016 SKODA SUPERB tow

CAUTIONNever fold and stow the through-loading bag when it is wet - risk of damaging
the through-loading bag.
Electrical sockets
 Introduction
This chapter contains information on the following subjects:
12-volt socket in the front centre console
96
12 volt socket in the rear centre console
96
12 volt socket in luggage compartment
97
230-volt socket in the rear centre console
97WARNING■ Do not place anything on the dashboard. These objects might slide or fall
down when driving and may distract you from concentrating on the traffic –
risk of accident!■
Make sure that while driving no objects can enter the driver's footwell -
cause an accident!
■
Safely stow all devices during the journey to prevent them from being
thrown around the interior in the event of a sudden braking manoeuvre or
an accident – risk of death!
■
The devices may warm up during operation – risk of injury or fire!
■
Improper use of the power sockets and the electrical accessories can
cause fires, burns and other serious injuries.
■
The 12-Volt sockets also work if the ignition is switched off. When leaving
the vehicle, never leave persons who are not completely independent, such
as children, unattended in the vehicle.
CAUTION
When using the 12 volt power outlets the following notes are to be observed.■The sockets can only be used for the connection of approved electrical ac-
cessories with a total power consumption of up to 120 watts, otherwise the
electrical system of the vehicle may be damaged.■
Connecting appliances when the engine is not running will drain the battery
of the vehicle!
■
Before switching the ignition on / off or before starting the engine, switch
off the devices which are connected to the sockets - there is a risk of damage
to the equipment due to voltage fluctuations.
12-volt socket in the front centre consoleFig. 108
Cover of the 12 volt power outlet
Read and observe and on page 96 first.
›
To use , open the storage compartment, remove the cover of the socket
» Fig. 108 and plug the electrical appliance plug into the socket.
12 volt socket in the rear centre console
Fig. 109
Open the cover / 12 volt power outlet 
96Using the system

›Press the adapter and remove in the direction of the arrow 5 from the guide
rods of the headrest.WARNINGBe care with the adapter - otherwise there is a risk of finger injury.
Attach to the storage compartment in the rear armrest
Fig. 117
Open storage compartment / stowage compartment for holder /
remove holder
Read and observe
on page 99 first.
›
To insert , hold the lid on the recess
A
and fold open in the direction of ar-
row » Fig. 117 .
›
Insert the holder in the stowage compartment
B
until it stops.
›
To remove , pull the securing tab
C
in direction of arrow and take the holder
in direction of arrow out of the adapter.
›
Fold the cover closed against the direction of the arrow.
Handling the holderFig. 118
Tilting and rotating the holder
Fig. 119
Adjusting the holder size
Read and observe on page 99 first.
The holder may be by 30° in the direction of the arrow
1
tipped and by 360°
in the direction of arrow
2
turned » Fig. 118 .
›
To adjust the holder size , pull out the securing tab
A
in the direction of ar-
row
3
and push the part
B
in the direction of arrow
4
to the desired posi-
tion » Fig. 119 .
Note
If there is no external device in the holder, then we recommend that the partB is moved fully down. Otherwise, irritating noises may occur at certain
speeds.100Using the system

Luggage compartment coverFig. 126
Remove the luggage compartment cover
Fig. 127
Luggage compartment cover
stowed behind the rear seats
Read and observe and on page 101 first.
If the support straps
A
» Fig. 126 are attached to the boot lid, then opening
the lid will raise the boot lid cover (hereafter only referred to as "cover").
The cover can be removed from the vehicle and stowed behind the rear seat
backrests if required » Fig. 127. Before removing the cover, the sunshade at the
back must be rolled up » page 75.
Removing
›
On both sides of the boot lid, unhook the straps
A
in direction of arrow
1
» Fig. 126 .
›
Hold the raised cover and press on the two sides on the underside of the
cover in the area of the recess
C
.
›
Remove the cover in the direction of the arrow
2
.
Fitting›First, insert the front mounting B and then the rear mounting C in the re-
cess D
» Fig. 126 .
›
Press on the two sides on the upper side of the cover in the area of the re-
cess
D
. The mountings
B
and
C
must engage with the recess
D
on both
sides of the luggage compartment.
›
On both sides of the boot lid unhook the straps
A
.
WARNINGDuring the trip there must be no objects on the cover - risk of injury in the
event of sudden braking or a vehicle collision!
CAUTION
■ Observe the following instructions to avoid canting and the subsequent
damage to the cover or the side trim. ■ The cover must be inserted properly and the load must not exceed the
height of the cover.
■ The cover must not be jammed in the surrounding seal of the luggage com-
partment lid when it is in the raised position. ■ There must be no object in the gap between the cover in the raise position
and the rear backrest.■
Never fold the raised cover forwards to the rear seats - there is a risk of dam-
aging the cover and the boot lid.
104Using the system

Roll-up coverFig. 128
Roll-up cover: Pull out / roll up / intermediate position / remove
Fig. 129
Remove the left side cover / store roll-up cover
Read and observe
and on page 101 first.
Extending
›
Grasp the cover on the handle
A
and pull it out in the direction of the arrow
1
until it audibly clicks » Fig. 128.
Retracting›Push the cover in the handle area A in the direction of arrow 2. The cover
rolls up automatically to the intermediate position B
» Fig. 128 .
The cover rolls up fully by pressing the cover in the handle area
A
in direction
of arrow
3
. The rolled-up cover can now be removed.
Removing/inserting
›
Press on the side of the cross bar in the direction of arrow
4
and remove
the cover in the arrow direction
5
» Fig. 128 .
Insertion takes place in reverse order.
Stowage
If the vehicle is equipped with the variable loading floor, then the removable
roll-up luggage compartment cover can be stowed in the recesses of the lug-
gage compartment side trim.
›
Fold the variable loading floor into the upper position » page 110.
›
Open the side trays on both sides of the luggage compartment and remove
» Fig. 130 on page 106 -
 .
›
Remove the left side cover in the arrow direction
1

» Fig. 129 .
›
Insert the roll-up cover in the recesses of the side trim in the direction of ar-
row
2
and stow in the direction of arrow
3
.
›
Reinsert the left side cover in the opposite direction to the arrow
1
.
›
Close the side compartments on both sides of the luggage compartment.
›
Fold out the variable loading floor to the upper position.
WARNINGNo objects should be placed on the roll-up cover - there is a risk of damage
to the cover and a risk of injury in the event of a sudden stop or a vehicle
collision!
Note
If you want to stow the roll-up luggage compartment cover and the multifunc-
tion pocket at the same time , then it is necessary that the rear part of the roll-
up luggage compartment covers the multifunction pocket.
Roll-up cover - automatic rolling-up
Read and observe
and on page 101 first.
The automatic rolling up of the roll-up cover (hereafter as function) eases ac-cess to the luggage compartment. 
105Transport of cargo

When opening the boot lid with the function activated, the roll-up cover auto-
matic rolls-up of the intermediate position B » Fig. 128 on page 105 .
Activation/deactivation can be carried out in Infotainment in the menu 

→
 →
Opening and closing
.
Note
The setting (activation/deactivation) of the automatic rolling up is stored (de-
pending on the Infotainment type) in the active user account personalisation
» page 49 .
Side storage compartment and trays
Fig. 130
Side shelf removal / open side pocket
Read and observe
and on page 101 first.
Located at the two sides of the luggage compartment, depending on vehicle equipment are side trays » Fig. 130 - 
or lockable side compartments
» Fig. 130 - 
.
The space behind the tray and in the tray is provided for storing small objects
up to a total weight of 2.5 kg.
Side compartment
›
Remove the storage compartment cover in the direction of the ar-
row » Fig. 130 - 
.
To insert , proceed in reverse order.
Side compartment
›
To open , pull the handle in direction of arrow
1
and open the compartment
in the direction of arrow
2
» Fig. 130 
. The tray can be removed.
›
To close , swivel the compartment against the direction of arrow
2
.
Cargo elementFig. 131
Pull out Cargo elements: Variant 1 / Variant 2
Fig. 132
Pull out Cargo elements: Variant 3 / Load fastening example
Read and observe
and on page 101 first.
The cargo elements are designed for mounting and securing loads with a max- imum gross weight of 8 kg.
›
Before use, remove the Cargo elements in the direction of the arrows
» Fig. 131 and» Fig. 132 - 
.
›
Use the cargo elements to secure the load as close as possible to the rear
seats » Fig. 132 
.
›
After use, stow the Cargoelements in their original position.
106Using the system

Storage compartments under the floor coveringFig. 133
Variant 1: Lift flooring / storage compartments
Fig. 134
Variant 2: Lift flooring / storage compartments
Read and observe
and on page 101 first.
For vehicles that are not equipped with an emergency spare wheel located un- der the flooring of the luggage compartment
B
» Fig. 133 or » Fig. 134 .
Every storage compartment
B
is designed for storing small objects of up to 15
kg. in weight in total.
Using the storage compartments - variant 1
›
Lift the flooring via loop
A
in the direction of arrow » Fig. 133 and completely
fold back or fasten using the loop on the hook on the luggage compartment
cover.
›
Stow the cargo in the storage compartments.
›
Fold back the flooring against the direction of the arrow or remove it from
the hook.
When transporting tall objects in the compartments, the flooring must be fol- ded forward.
Using the storage compartments - variant 2›
Dividing the luggage compartment with variable loading floor » page 111.
›
Lift the floor covering in the direction of arrow » Fig. 134 and hook into hook
C
on the upper edge of the variable loading floor.
›
Stow the cargo in the storage compartments.
›
Unhook hook
C
and fold back the flooring against the direction of the arrow
(fold back the variable loading floor to the initial position if necessary).
When transporting tall objects in the compartments, the hook
C
must be
hooked onto the upper edge of the variable loading floor.
CAUTION
■ Before closing the boot lid check that the flooring is not attached to the
hook with the loop A » Fig. 133 - there is a risk of damaging the hook.■
Before closing the boot lid, check that the cargo transported in the storage
compartments does not strike against the luggage compartment cover - there
is a risk of damage to the lid.
107Transport of cargo

Multi-function pocketFig. 135
Multi-function pocket: Pull out / insert / push in / remove
Fig. 136
Remove the left side cover / store multifunction tray
Read and observe
and on page 101 first.
The multifunction pocket (following as pocket) is provided for the storage of
clothing and light objects with no sharp edges.
The maximum permissible load of the multifunction box is 3 kg.
Removal and fitting›Fold down the front hooks on both sides of the luggage compartment in the
direction of arrow 1
» Fig. 135 .
›
Grasp the rear bar
A
with both hands and withdraw the pocket in arrow di-
rection
2
.
›
Place the rear bar onto the two hooks that are folded forward in the direc-
tion of the arrow
3
all the way to the stop.
Pushing in
›
Remove the rear bar of the hook in direction of arrow
4
push in the pocket
in the direction of arrow
5
» Fig. 135 .
›
Place the rear bar against the front bar and press them together at both
ends
B
.
›
The front hooks on both sides of the luggage compartment fold back oppo-
site to the direction of arrow
1
.
Removing/inserting
›
Remove the roll-up luggage compartment cover » page 105.
›
Remove the pocket from the fittings in the direction of the arrow
6
» Fig. 135.
Insertion takes place in reverse order.
›
Insert the end of the bar marked 
 in the right-hand mounting, and the end
marked 
 in the left-hand mounting. The arrows should be pointing forward.
Stowage
If the vehicle is equipped with the variable loading floor, then the removable
pocket cover can be stowed in the recesses of the luggage compartment side
trim.
›
Fold the variable loading floor into the upper position » page 110.
›
Open the side trays on both sides of the luggage compartment » Fig. 130 on
page 106 -
 .
›
Remove the left side cover in the arrow direction
1

» Fig. 136 .
›
Insert the pocket in the recesses of the side trim in the arrow direction
2
and stow in the direction of arrow
3
.
›
Reinsert the left side cover in the opposite direction to the arrow
1
.
›
Close the side compartments on both sides of the luggage compartment.
›
Fold out the variable loading floor to the upper position.
Note
If you want to stow the roll-up luggage compartment cover and the multifunc-
tion pocket at the same time , then it is necessary that the rear part of the roll-
up luggage compartment covers the multifunction pocket.108Using the system

Positions of the variable loading floorFig. 139
Set variable loading floor to the upper position / variable loading
floor in the upper position
Fig. 140
Set variable loading floor to the lower position / variable loading
floor in the lower position
The variable loading floor can be set to the upper or lower position.
Set to the upper position
›
Lift the variable loading floor by the handle
A
» Fig. 139 about 20 cm high and
pull towards you.
›
Lift the loading floor to the height of the roll-up luggage compartment cover
in the direction of arrow
1
until you hear the clicking sound and press for-
ward.
The space below the variable loading floor can be used for stowing objects
such as the removed roll-up luggage compartment cover » page 105, the multi-
function pocket » page 108 etc.
The maximum permissible load of the variable loading floor is 75 kg. For the
transport of heavy loads, adjust the variable loading floor in the lower position
» Fig. 140 .
Set into the lower position›
Check that the area below the variable loading floor is empty.
›
Lift the variable loading floor by the handle
A
» Fig. 140 over the loading
edge in the direction of arrow
2
.
›
Pull the loading floor towards you in the direction of arrow
3
until it sinks to
the bottom position, and push forward.
Fold together / fold out the variable loading floor
Fig. 141
Fold up variable loading floor / folded variable cargo floor in the
upper position
›
To fold together , hold the variable loading floor on the handle
A
and lift in
the direction of arrow
1
» Fig. 141 .
›
Fold up the variable loading floor by moving it in the direction of the arrow
2
.
Folding out takes place in reverse order.
The variable loading floor is folded together / out in the same way in the upper
and lower position.
110Using the system