2016 Seat Leon Sportstourer Owner's manual

Fuses and bulbs
Change the front bulbs Dip ped he
a
dlight bulbFig. 102
Dipped beam headlights. Fig. 103
Dipped beam headlights. –
Raise the bonnet.
– Move the loops ››
›
Fig. 102 1 in the direc-
tion of the arr
o
w and remove the cover. –
Remov
e connector ››› Fig. 103 2 from the
b u
l
b.
– Unclip the retainer spring ›››
Fig. 103 3 pressing inwards to the right.
– Extract the bulb and fit the replacement so
th at
the lug on the b

ase fits into the recess
on the reflector.
Day light bulb Fig. 104
Day light bulb. –
Raise the bonnet.
– Turn the bulb holder ››
›
Fig. 104 1 to the
l ef
t
and pull.
– Remove the bulb by pressing on the bulb
holder and t

urning it anti-clockwise at the
same time.
– Installation involves all of the above steps
in rever

se sequence. Turn signal bulb
Fig. 105
Turn signal bulb. Fig. 106
Turn signal bulb. –
Raise the bonnet.
– Move the loop ››
›
Fig. 105 1 in the direc-
tion of the arr
o
w and remove the cover.
– Turn the bulb holder ›››
Fig. 106 2 anti-
c loc
k
wise and pull. »
95
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
– Remo
v
e the bulb by pressing on the bulb
holder and turning it anti-clockwise at the
same time.
– Installation involves all of the above steps
in rever

se sequence.
Main beam headlight bulb Fig. 107
Main beam headlight bulb. Fig. 108
Main beam headlight bulb. –
Rai
se the bonnet

.
– Move the loop ›››
Fig. 107 1 in the direc-
tion of the arr
o
w and remove the cover.
– Slide connector ›››
Fig. 108 2 to the left or
right and p
u
ll.
– Remove the bulb by disconnecting the con-
nector.
– In

stallation involves all of the above steps
in rever
se sequence. Fog light bulb* 3 Valid only for versions with incandescent bulbs
Fig. 109
Fog light: extracting the grille.96

Fuses and bulbs
Fig. 110
Fog light: remove the bulb holder Follow the steps indicated:
Remo
v
e the screw ››› Fig. 109 1  fr
om
the f og light

grille using a screwdriver
and extract the grille.
Remove the 3 screws ››› Fig. 109 2 .
R emo
v

e the metal clip situated on the
upper part of the fog light by pulling
away from the vehicle 3  and t
ake
the f og light

out.
Remove the connector ››› Fig. 110 1 from the bulb.
T
urn the b
u

lb holder 2 anti-clockwise
and p u
l

l.
Remove the bulb by pressing on the
bulb holder and turning it anticlockwise
at the same time.
Installation involves all of the above
steps in reverse sequence.
Check that the bulb works properly.
1.
2.
3.
4.
5.
6.
7.
8. Note
● Due to the difficulty of accessing fog light
bu l

bs, have them replaced at a Technical
Service or specialised workshop.
● LED fog light bulbs should be replaced by
speci
alised personnel. Changing incandescent rear
light b
u

lbs
Rear lights summary Tail lights on side panel
Turn signalPY21W NA LL
Side light and brake lightP21W LL
Tail lights on the rear lid
Left side
Side lights2x W5W LL
Fog lightsH21 W
Right side
Side lights2x W5W LL
Reverse lightP21W LL The table corresponds to a right-hand traffic
v
ehic
l

e. The position of lights may vary ac-
cording to the country.
97
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
Rear bulbs (in the side panel) Fig. 111
Luggage compartment: location of
the bo lt
sec
uring the tail light unit. Remove
the rear light unit from side panel. Fig. 112
Retaining tabs on reverse side of tail
light. –
Check which of the bulbs is defective.
– Open the rear lid.
– Remove the cover by prying the flat side of
a s c
r

ewdriver into the recess and remove
the cover from the opening ››› Fig. 111 1 .
– Carefully loosen the screw located behind
the c o
v

er with a screwdriver, turning it anti-
clockwise ››› Fig. 111 2 .
– Tilt the light in the direction of the arrows
unti
l

it comes out of its housing (positions
3 and
4 )
››
› Fig. 111
.
– Remove the bulb holder ›››
Fig. 112 unlock-
ing the retaining tabs 1 .
– Change the damaged bulb.
– To refit follow the steps in reverse order,
tak
in

g special care when fitting the bulb
holder. The securing tabs must click into
place. CAUTION
Take care when removing the rear light unit to
mak e s

ure there is no damage to the paint-
work or any of its components. Note
Make sure you have a soft cloth ready to
pl ac

e under the glass on the rear light unit, to
avoid any scratches. 98

Fuses and bulbs
Rear lights bulbs (in the rear lid) Fig. 113
Remove the cover from the rear lid
and det ac
h the b
ulb holder. Fig. 114
Position of the bulbs in the bulb
hol der The rear lid must be open to change the
b
u
l

bs.
– Remove the rear lid cover in the direction
indicated b

y the arrow ››› Fig. 113 .
– Unlock the retaining tabs A of the bulb
ho l
der

, following the direction of arrows 1 and
2
› ›
› Fig. 113
.
– Remove the bulb holder by turning it in the
direction of arr

ow 3
› ›
› Fig. 113 .
– Lightly press the defective bulb into the
bul

b holder 1 , then turn it to the left
2 and remove it
››
›
Fig. 114.
– Fit the new bulb, pressing it into the bulb
holder and t

urn it to the right as far as it
will go.
– Use a cloth to remove any fingerprints from
the glas

s part of the bulb.
– Check that the new bulb works properly. –
Reins
tall the bulb holder making sure that
locking clips A
› ››
Fig. 113
 are properly
clipped.
– Replace the cover of the rear lid lining.
Rear LED light bulb (in the rear lid) Fig. 115
Remove the cover from the rear lid Fig. 116
Remove the bulb holder. » 99
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
The rear lid must be open to change the
b u
l
bs.
– Remove the rear lid cover in the direction
indicated ›

›› Fig. 115.
– Turn the bulb holder anti-clockwise in the
direction of the arr

ow 1
› ››
Fig. 116
.
– R
emove the bulb holder from its housing
2 .
– Replace the defective bulb and return the
bu
l

b holder to its housing, following the
same steps in reverse order.
– Check that the new bulb works properly.
Changing number plate light bulbs Fig. 117
In the rear bumper: number plate
light . Fig. 118
Number plate light: Remove the bulb
hol der
. Follow the steps indicated:
1. Press the number plate light in the direc-
tion of the arr
o

w ››› Fig. 117.
2. Remove the number plate bulb slightly.
3. In the connector lock, turn ›››
Fig. 118 to-
wards the arrow 1 and pull the connec-
t or
.
4.
Rotate the bulb holder in the direction of
arrow 2 and extract it with the bulb.
5. Replace the defective bulb with a new bu
l

b with the same features.
6. Insert the bulb holder in the number plate light and turn in the op
posite direction of
arrow 2 until it stops.
7. Plug the connector into the bulb holder. Note
Depending on how equipped the vehicle is,
the number pl at

e lights may be LEDs. LEDs
have an estimated life that exceeds than that
of the car. If a light with LEDs fails, go to an
authorised workshop for replacement. 100

Operation
Fig. 119
Instruments and controls.102